2016 Seat Ibiza ST remove seats

The essentials
Operation of the panoramic sunroof Fig. 10
Emergency operation of the panoram-
ic/ti ltin
g su
nroof. In case of a breakdown, the sunroof may be
c
lo
sed m anual

ly.
● Remove the plastic cover by inserting a
screwdriv
er into the rear section.
● Insert an Allen key (4 mm) into the opening
as far a
s possible and close the sunroof. Before driving
Manually
adjusting the front seats Fig. 11
Front seats: manual seat adjustment. Forward/back: pull the lever and move
the se
at
for

wards or backwards.
Raising/lowering: pull/push the lever.
Tilting the backrest: turn the hand wheel.
Folding down the backrest (only 3-door
vehicles): pull the lever and push the
backrest forward.

››› in Adjusting the front seats on
page 128 1
2
3
4 Adjusting the head restraints
Fig. 12
Front seat: adjustment of the head re-
s tr
aint . ●
Grab the sides of the head restraints with
both h and
s and p

ush upwards to the desired
position. To lower it, repeat the same action,
pressing the 1 button on the side.

››› in Adjusting or disassembling the
head restraints on page 129
››› page 60, ››› page 129 12

The essentials
Ways to secure a child seat Fig. 25
On the rear seats: Possible installations
for the chi l
d seat. Figure
›››
Fig. 25
A shows the basic child re-
s tr
aint sy

stem mounting using lower retain-
ing rings and the upper retaining strap. Fig-
ure ››› Fig. 25 B shows the child restraint
sy s
tem mou

nting using the vehicle seat belt.
You can secure a child seat to the rear seat or
front passenger seat in the following ways:
● Child seats in groups 0 to 3 can be sec
ured
with a seat belt.
● Child seats for groups 0, 0+ and 1 can be
fas
tened without seatbelts, using the “ISO-
FIX” system, using the “ISOFIX” ››› page 18
securing rings.
● During installation of some models of
group I, II and III chil
d seats in the rear seat,
difficulty may arise in mounting given that
the seat comes into contact with the head re- straint. In this case, adjust the height of the
head re

straint or remove it from the seat fol-
lowing the instructions in the corresponding
chapter ›››
 page 129. Once you remove
the child seat, replace the head restraint in
its original position. » 17

Safety
WARNING
● Any inc orr
ect sitting position increases the
risk of severe injuries.
● Sitting in an incorrect position exposes the
vehicle oc
cupants to severe injuries if airbags
are triggered, by striking a vehicle occupant
who has assumed an incorrect sitting posi-
tion.
● Before the vehicle moves, assume the prop-
er sitting pos
ition and maintain it throughout
the trip. Before every trip, instruct your pas-
sengers to sit properly and to stay in this po-
sition during the trip ››› page 57, Correct posi-
tion for passengers. Correct adjustment of front head re-
s
tr
aint s Fig. 77
Correctly adjusted head restraint as
v iew
ed fr om the fr

ont and the side. Properly adjusted head restraints are an im-
por
t
ant p

art of passenger protection and can
reduce the risk of injuries in most accident
situations.
– Adjust the head restraint so that its upper
edge is, as

far as possible, at the same lev-
el as the top of your head, or at the very
least, at eye level ››› Fig. 77. WARNING
● Trav el

ling with the head restraints removed
or improperly adjusted increases the risk of
severe injuries. An improper adjustment of
the head restraints may cause death in an ac-
cident and increase the risk of suffering inju-
ries during abrupt braking actions or unex-
pected manoeuvres.
● The head restraints must always be adjus-
ted accor
ding to the height of the passenger. Correct adjustment of rear head re-
s
tr
aint s Fig. 78
Rear head restraint adjustment. The rear head restraints have 2 positions:
● Raised position or position for use A ›››
Fig. 78. In this po s ition, the head restraint
is used normally, protecting the occupant of
the rear seats, along with the rear seat belts.
● Rest position, not in use B
› ›
› Fig. 78 .
This
position improves the driver's rear visibility.
To fit the head restraint in position for use A , pull on the edges with both hands in the
dir ection of
the arro

w. To place it in rest posi-
tion B , lower the head restraint.
WARNING
● Whenever a pa s

senger is seated on the rear
seats, the head restraint should be placed in
the position for use A .
60

Safety
only if the seat belt is being worn. This re-
tr acts
and tight en
s the seat belts, reducing
the forward motion of the occupants.
The belt tensioners will not be triggered in
the event of minor collisions, if the vehicle
overturns, or in accidents where no major
forces act on the vehicle. Note
● If the seat belt

tensioners are triggered, a
fine dust is produced. This is normal and it is
not an indication of fire in the vehicle.
● The relevant safety requirements must be
observ
ed when the vehicle or components of
the system are scrapped. Specialised work-
shops are familiar with these regulations,
which are also available to you. Service and disposal of belt tension-
er
s The belt tensioners are components of the
se
at
belts th

at are installed in the seats of
your vehicle. If you work on the belt tension-
ers or remove and install parts of the system
when performing other repair work, the seat
belt may be damaged. The consequence may
be that, in the event of an accident, the belt
tensioners function incorrectly or may not
function at all.
So that the effectiveness of the seat belt ten-
sioner is not reduced and that removed parts do not cause any injuries or environmental
pollution, re

gulations, which are known to
the specialised workshops, must be ob-
served. WARNING
● Improper use or r ep

airs not carried out by
qualified mechanics increase the risk of se-
vere or fatal injuries. The belt tensioners may
fail to trigger or may trigger in the wrong cir-
cumstances.
● Never attempt to repair, adjust, remove or
insta
ll parts of the belt tensioners or seat
belts.
● The seat belt tensioner, seat belt and auto-
matic retr
actor cannot be repaired.
● Any work on the belt tensioners and seat
belts, including the r
emoval and refitting of
system parts in conjunction with other repair
work, must be performed by a specialised
workshop only.
● The belt tensioners will only provide pro-
tection for one acc
ident and must be changed
if they have been activated. Airbag system
Brief intr
oduction
Wh y

is it so important to wear a seat
belt and to sit correctly? For the inflating airbags to achieve the best
protection, the se
at

belt must always be worn
properly and the correct sitting position must
be assumed.
The airbag system is not a substitute for seat
belts, but it is an integral part of the vehicle's
overall passive safety system. Please bear in
mind that the airbag system can only work ef-
fectively when the vehicle occupants are
wearing their seat belts correctly and have
adjusted the head restraints properly. There-
fore, it is most important to properly wear the
seat belts at all times, not only because this
is required by law in most countries, but also
for your safety ›››
page 61, Why wear a seat
belt?.
The airbag inflates in a matter of seconds, so
if you are not properly seated when the air-
bag is triggered, you may sustain fatal inju-
ries. Therefore, it is essential that all vehicle
occupants assume a correct sitting position
while travelling.
Sharp braking before an accident may cause
a passenger not wearing a seat belt to be
thrown forward into the area of the deploying
66

Safety
●
The side and hea d airb
ags are managed
through sensors located in the interior of the
front doors. To ensure the correct operation of
the side and curtain (head) airbags neither
the doors nor the door panels should be
modified in any way (e.g. fitting loudspeak-
ers). If the front door is damaged, the airbag
system may not work correctly. All work car-
ried out on the front door must be done in a
specialised workshop.
● In a side-on collision the side airbags will
not work if
the sensors do not correctly meas-
ure the pressure increase on the interior of
the doors, due to air escaping through the
areas with holes or openings in the door pan-
el.
● Never drive if the interior door panels have
been removed or if
the panels have not been
correctly fitted.
● Never drive the vehicle if the loudspeakers
in the door panels h
ave been removed, un-
less the holes left by the loudspeakers have
been closed properly.
● Always check that the openings are closed
or cover
ed if additional loudspeakers or other
equipment are fitted inside the door panels.
● Any work carried out to the doors should be
made in an authorised s
pecialised workshop.Curtain airbags*
Read the additional information carefully
› ›
›
 p

age 16. WARNING
The airbag is deployed at high speed in frac-
tions of a sec

ond.
● Do not obstruct the head-protection airbag
deployment ar
eas.
● Never secure objects over the curtain air-
bag cov
er or in its deployment area.
● Occupants of the front seats and rear side
seats mu
st never carry any other people, ani-
mals or objects in the deployment space be-
tween them and the airbags. Make sure that
all the vehicle occupants, including children,
observe this.
● The clothes hangers are intended only for
light articl
es of clothing. Do not leave any
heavy or sharp-edged objects in the pockets.
● Do not mount accessories on the doors.
● Use only sun blinds which have been ex-
press
ly approved for use in your vehicle.
● Do not turn the sun blinds towards the win-
dows if
there are objects, e.g. pens or garage
remote controls, secured to them. Deactivating airbags
D e
activ ation of

front passenger front
airbag* Fig. 85
In the glove compartment: Switch for
activ atin
g and de activ

ating the front passen-
ger airbag Fig. 86
Centre side of dash panel: control
l amp f
or deactiv

ated front passenger airbag
in centre console 70

Seats and head restraints
Vehicles without the Easy-Entry function
– To f old the backrest, pull the lever 1 up-
w ar
ds
and push the backrest forwards.
– To unfold the backrest, push it back.
Vehicl
es with the Easy-Entry function
– To fold the backrest, pull the lever 1 up-
w ar
ds

and push the backrest forwards. You
can push the seat forwards at the same
time to make entry to the rear seats easier.
– To unfold the backrest, first move the seat
compl
etely back.
The Easy-Entry function facilitates the access
to the vehicle rear seats. Before lifting the
backrest, return the seat to the original posi-
tion. The seat inserts when the backrest is lif-
ted. Adjusting or disassembling the head
restr

aints Fig. 141
Adjusting and removing the head re-
s tr
aints. Read the additional information carefully
› ›
›
 p

age 12
Adjusting height (front seats)
– Press the button on the side and pull up-
wards

to the desired position.
– To lower the head restraint, press the but-
ton and push he

ad restraint downwards.
– Make sure that it engages securely into one
of its pos

itions.
Adjusting height (rear seats)
– Press the button on the side and pull up-
wards

to the desired position.
– To lower the head restraint, press the but-
ton and push he

ad restraint downwards. –
Make sur
e that the head restraint engages
securely in one of its positions ››› page 60.
Removing the head restraint – Push the head restraint up as far as it will
go.
– Pre

ss the button ››› Fig. 141
(arrow).
– Pull head restraint out of fitting without re-
leas

ing the button.
Fitting the head restraint
– Insert the head restraint into the guides on
the corres

ponding backrest.
– Push head restraint down.
– Adjust the head restraint to suit body size
››› p

age 60. WARNING
● Never drive if the he

ad restraints have been
removed. Risk of injury.
● Never drive if the head restraints are in an
unsuit
able position (the lowest position) as
there is a risk of serious injury.
● After refitting the head restraint, you must
alway
s adjust it properly for height to achieve
optimal protection.
● Please observe the safety warnings in ››› in Correct adjustment of front head restraints
on page 60
. » 129
Technical data
Advice
Operation
Emergencies
Safety

Operation
Note
● To fit and r emo
ve the rear head restraints,
gently tilt the seat backrest forwards.
● When fitting the head restraints again, in-
sert the tube
s as far as possible into the
guides without pressing the button. Seat functions
Heated se at

s* Fig. 142
Front seat heating switch. The front seat cushions and backrests can be
he
at
ed el ectric

ally.
– Press the corresponding switch ››› Fig. 142
t
o switch on the seat heating.
– Press once to connect the heating at maxi-
mum force.

The two LEDs illuminate
››› Fig. 142. After 15 minutes of high inten- sity, the upper LED goes out, the system is
deactivated f

or 2 minutes and is then reac-
tivated at low intensity (the lower LED re-
mains on permanently).
– Press the switch again to set the heating to
minimum force. (The lo

wer LED lights up).
– To disconnect the heating, press the switch
again. CAUTION
To avoid damaging the heating elements,
ple a

se do not kneel on the seat or apply
sharp pressure at a single point to the seat
cushion and backrest. Note
The seats are only heated electrically when
the engine is ru

nning. Folding down the back seat
Fig. 143
Folding up the rear seat cushion. Fig. 144
Button for unlocking the rear back-
r e
st

. Folding seat down
– Remove the head restraint ››
›
p
age 129.
– Pull the front edge of the seat cushion
››› Fig. 143

1 upwards in the direction of
the arr o
w .
130

Transport and practical equipment
– Lif t
the c u
shion 2 forwards in the direc-
tion of the arr
ow
.
– Pull the release button ››› Fig. 144 in the di-
r
ection of the arrow and fold the backrest
forwards.
– Insert the head restraints in the spaces on
the rear of the se

at cushion which are visi-
ble when the seat cushion is lowered.
Folding seat forward
– Remove the head restraints from the
space

s in the seat cushion.
– Lift the backrest, and before securing it, re-
place the he

ad restraints in the seat cush-
ion, and then click the seat correctly onto
the locking rails.
– Once the backrest is locked, pull on the
central se

at belt or directly on the backrest
to check that the backrest has properly en-
gaged in position.
– Check that the position lever is in neutral
position.
– Lo

wer the cushion and push it backwards
below the seat belt
buckles.
– Press the front part of the cushion down-
wards.
On s

plit rear seats*, the backrest and cush-
ion can be lowered and raised respectively in
two sections. WARNING
● Plea se be c

areful when folding back the
backrest! Injuries can be caused if the seat
height is adjusted without due care and at-
tention.
● Do no trap or damage seat belts when rais-
ing the back
rest.
● After raising the backrest, check it has en-
gaged properly
in position. Do this by pulling
on the central seat belt or directly on the
backrest and check that the position lever is
in the neutral position.
● The three point automatic seat belt only
works c
orrectly when the backrest of the cen-
tral seat is correctly engaged. Transport and practical
equipment
Pr actic
al

equipment
Glove compartment Fig. 145
Passenger side: glove compartment. Fig. 146
Glove compartment: storage com-
p ar tment
f

or instruction manual. » 131
Technical data
Advice
Operation
Emergencies
Safety