2016 RENAULT TWINGO Owners Manual

3.17
Centre console storage
compartment 5
PASSENGER COMPARTMENT STORAGE, FITTINGS (2/4)
When turning corners,
accelerating or braking,
ensure that the recepta-
cle being held by the cup
holder is not dislodged.
There is a risk of injury if hot liquid
escapes.
Centre console storage
compartment 7
Depending on the vehicle, it is closed
with a cover 8.
6
Cup holder 6
This can be used for storing a mobile
ashtray, drinks cans, etc.
78
5

3.18
PASSENGER COMPARTMENT STORAGE, FITTINGS (3/4)
9
Rear door storage
compartment 9
Storage compartments can hold a
1.5 litre bottle.
10
Cup holder 10
This can be used for storing a mobile
ashtray, cup holder, etc.
When turning corners,
accelerating or braking,
ensure that the recepta-
cle being held by the cup
holder is not dislodged.
There is a risk of injury if hot liquid
escapes.
11
Rear centre console storage
compartment 11
Ensure that no hard, heavy
or pointed objects are
placed in the “open” storage
compartments in such a
way that they may fall onto passen-
gers during sudden turning, braking
or in the event of an accident.

3.19
PASSENGER COMPARTMENT STORAGE, FITTINGS (4/4)
12
Storage compartment under
the rear bench seat 12
14
Sun visor storage 13
This can be used for storing motorway
tickets, cards, etc.
14
15
Front sun visor
Lower sun visor 14.
Courtesy mirrors
Lift the cover 15.
When driving, ensure the
courtesy mirror cover is
closed. Risk of injury.
13

3.20
Accessories socket 2
It is provided for connecting accessories
approved by our Technical Department.
Ashtray A
It can be housed in either position 1
or 3.
Cigarette lighter 2
With the ignition on, push in the ciga-
rette lighter 2. It will spring back with a click when it is ready. Pull it out to use.
After use, replace it without pushing it
all the way in.
ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET
1
If your vehicle is not fitted with a
cigar lighter and an ashtray, these
can be obtained from an approved
Dealer.
3
2A
Connect accessories with
a maximum power of
120 watts (12 V) only.
When several accessory
sockets are used at the same time,
the total power of the connected
accessories must not exceed
180 watts.
Fire hazard.

3.21
The headrest is a safety
component; check that it is
fitted and in the correct po-
sition. The top of the head-
rest should be as close as possible
to the top of the head.
To raise the headrest
Raise the headrest as far as it will go,
then press button A and remove the
headrest.
If necessary, fold the seatback down to
take out the headrest (see the informa-
tion on the “Rear bench seat” in
Section 3).
To refit the headrest
Enter the rods in their housing and
push down the headrest until it locks to
use it in the high position. Check that it
is correctly locked.
Position for use
Raise the headrest as far as possible to
use it in the high position. Check that it
is correctly locked.
Storage position
Press button A and lower the headrest
completely.
When the headrest is set at the
lowest position, this is for storage
only. It should not be in this position
when a seat is occupied.
REAR HEAD RESTS
A

3.22
REAR BENCH SEAT
B
To fold down the seatback:
– Ensure that the front seats are far enough forward;
– Lower the headrest as far as it will go;
– Place the seat belts in their guides A;
– Pull the tab 1 upwards and lower the seatback B.
To raise the seatback again, proceed
in the reverse order. Ensure that it is
properly secured in place.
Refit the seatback and click it back into
place. Increasing the boot volume (depend-
ing on the vehicle)

The seatback can be made vertical in
order to increase the boot volume:
– pull the tab 1 and lower the seat-
back B;
– lift the rod 2 until it locks in place;
– lift the seatback B and click it onto
the rod 2, ensuring that it is properly
locked in place.
To return to the initial position:
– pull the tab 1 and lower the seat-
back B;
– lower the rod 2 as far as it will go;
– raise the seatback B and make sure it properly locks in place.
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
When moving the rear
seats, ensure that nothing
obstructs the anchorage
points (passenger’s arm or
leg, a pet, gravel, cloth, toys, etc.).
When refitting the seat-
back, make sure it is cor-
rectly locked in place.
If seat covers are fitted ,
make sure these do not prevent the
seatback latch from locking in.
Make sure that the seat belts are
positioned correctly.
Reposition the headrests.
1
A
2
12
B

3.23
Opening the doors manually
from the inside
If it is impossible to unlock the tailgate,
it can be done manually from inside:
– access the luggage compartment by tilting the rear bench seatback(s),
– insert a pencil or similar object in recess 5 and slide the unit as shown
in the illustration;
– push the boot lid to open it.
BOOT
To open
Without remote control
With the doors unlocked, press the
button 2 and lift the boot lid 1.
With remote control
With the doors unlocked or not, press
the button 3 on the remote control A
or B for 2 seconds and lift the boot lid 1.
In this case, upon closing, the boot will
still be unlocked: remember to lock the
vehicle before leaving.
1
5
4
To close
Lower the boot lid using the handle
inside the boot 4 to assist you.
2
As the engine is located under the
boot carpet, do not slide or store an-
ything under the boot carpet.
3
A
B
3

3.24
LUGGAGE COVER
1
Removal
– Unhook the two straps 1;
– depending on the vehicle, detach the flexible section attached to the rear
bench seatback;
– lift the boot cover and unclip it by pulling it towards you.
Refitting
To refit, proceed in the reverse order to
removal.Do not place any heavy or
solid objects on the luggage
cover. These may pose a
risk to the vehicle occu-
pants if the driver has to brake sud-
denly or if the vehicle is involved in
an accident.