2016 Peugeot Traveller Row 3

51
Traveller-VP_en_Chap02_ouvertures_ed01-2016
Changing the battery
Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
Take them to an approved collection
point.If the battery is flat, you are
informed by lighting of this warning
lamp in the instrument panel, an audible signal
and a message in the screen.
Reinitialisation
Locking the side-hinged doors
F If fitted to your vehicle, check that the
electric child lock is not on.
F
o
p
en the left-hand door. Battery ref.: CR1620 / 3 volts.
F
L
ock the driver's door using the
key.
F

P
ress one of the remote control
buttons.
F

T
urn the key to position 2 (Ignition on).
F

S
witch off the ignition and remove the key
from the ignition switch.
The remote control is fully operational again.
Unlocking
F use the interior door handle.
Remote control problem
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F

F
irst of all, use the key in the lock to unlock
or lock your vehicle.
F

T
hen reinitialise the remote control.
If the problem persists, contact a P
e

ugeo
T
d

ealer as soon as possible.
F

I

nsert the key into the latch aperture on the
edge of the door (without forcing) and slide
the assembly upward.
F

R

emove the key.
F

C

lose the door and check from the outside
that it has locked correctly. F
u
n
clip the cover using a screwdriver in the
cut-out.
F

R
emove the cover.
F
e
x
tract the flat battery from its location.
F

P
lace the new battery into its location
observing the original direction.
F

C
lip the cover in place.
2
Access

62
Traveller-VP_en_Chap02_ouvertures_ed01-2016
Changing the cell battery
Battery ref.: CR2032 / 3 volts.
This replacement battery is available from a
P
e
ugeo
T d
ealer or a qualified workshop.
A message appears in the instrument panel
screen when replacement of the battery is needed.
Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
Take them to an approved collection
point.
F

P

lace the remote control against the
reader.
F

K

eeping it in place, switch on the ignition
by pressing "START/ST
oP

".
The remote control is fully operational again.
Reinitialisation
Remote control problem
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F

F
irst, use the integral key in the door lock
to unlock or lock your vehicle.
F

T
hen, reinitialise the remote control.
If the problem persists, contact a
P
e

ugeo
T d
ealer or a qualified
workshop as soon as possible.
F
u
n
lock the driver's door using the integral
key.
F

P
ress one of the remote control
buttons.
F

P
lace the integral key in the lock to unlock
your vehicle. F
u
n
clip the cover using a small screwdriver
at the cutout.
F

L
ift off the cover.
F

R
emove the flat battery from its location.
F

F
it the new battery into its location
observing the original direction of fitment.
F

C
lip the cover onto the casing.
Access

96
Traveller-VP_en_Chap03_ergonomie-et-confort_ed01-2016
F If your vehicle has the facility, place the seat backrest in the table position.
Tipping, access to row 3 Removing a seat
F If your vehicle has the facility, place the backrest in the table position.
F

T
ip the seat for ward.
F
u
s

ing the handle, release the rear feet then
tip the seat for ward.
F

T

o return the seat, tip the bench towards
the rear until the feet lock into place.
It is not necessary to fold the backrest
(table position) to tip the bench seat for
access to row 3. F

R
elease the front feet using these handles.
F

D
isengage the seat from its anchorages.
F

R
emove the seat. If removing and storing a bench seat
out of the vehicle, ensure that it is
placed in a clean area, so as to avoid
introducing any foreign bodies into the
mechanisms.
The bench seats are not designed for
any use other than in the vehicle. They
have mechanisms and functions that
could be damaged if used incorrectly or
are dropped.
ease of use and comfort

99
Traveller-VP_en_Chap03_ergonomie-et-confort_ed01-2016
F If your vehicle has the facility, place the backrest in the table position.
Fully folding a seat, access to row 3
(example of an individual seat)
It is not necessary to fold the backrest
(table position) to tip the bench seat for
access to row 3.
F
u
s
ing the handle, release the rear feet then
tip the seat for ward.
F

T
o return the seat to the normal position,
unfold the seat backwards until the rear
feet engage in their anchorages.
F

F

old the backrest onto the cushion.
F

T

o return the backrest to the normal
position, raise the lever and pull the
backrest up (from the rear, lower the lever).
Removing a seat
(example of an individual seat)
F

I
f your vehicle has the facility, place the
backrest in the table position.
F

T
ip the seat for ward.
F

R
elease the front feet using the handles.
F

D
isengage the seat from its anchorages.
F

R
emove the seat by the sliding door in
row
2 or from the rear in row 3.
3
ease of use and comfort

103
Traveller-VP_en_Chap03_ergonomie-et-confort_ed01-2016
Removing a seat
(example of an individual seat)
F M ove the seat for ward for access to the strap.
F

F
old the backrest to the table position.
Return the backrest to the normal
position (between the markings)
To return the backrest to the normal position,
the seat must be positioned between the
markings.
The arrow must not be outside the markings.
Do not use the strap to lift the seat or
bench seat.
F
u
s
e the front control to move the seat so
that it is between the markings. F

F
rom the rear, pull the strap fully, to release
the anchorages and tip the seat for ward to
the vertical position.
F

T
ake the seat out through the sliding door
in row 2 or from the rear in row 3. If removing and storing a seat (or bench
seat) out of the vehicle, ensure that it is
placed in a clean area, so as to avoid
introducing any foreign bodies into the
mechanisms.
The seats (or bench seats) are not
designed for any use other than in the
vehicle. They have mechanisms and
functions that could be damaged if used
incorrectly or if the seat is dropped.
3
ease of use and comfort

107
Traveller-VP_en_Chap03_ergonomie-et-confort_ed01-2016
Removing a seat
F Move the seat for ward for access to the strap.
F F old the backrest to the table position.
Do not use the strap to lift seat. Do not use the strap to lift the seat. Before refitting a seat to the vehicle,
pull the strap fully to ensure that the
latching mechanism has engaged.
F

F
rom the rear, pull the strap, going
beyond the point of resistance, to free the
anchorages and tip the seat for ward to the
vertical position.
F

T
ake the seat out through the sliding door
in row 2 or from the rear in row 3.
Refitting a seatIf removing and storing a seat out of
the vehicle, ensure that it is placed
in a clean area, so as to avoid
introducing any foreign bodies into the
mechanisms.
The seats are not designed for any use
other than in the vehicle. They have
mechanisms and functions that could
be damaged if used incorrectly or are
dropped.
3
ease of use and comfort

109
Traveller-VP_en_Chap03_ergonomie-et-confort_ed01-2016
Precautions for the
seats and bench
seats
Following the various handling operations:
- d o not remove a head restraint without
storing it and fixing it to a support,
-

c
heck that the seat belts are always
accessible to the passenger and easy to
fasten,
-

a p
assenger must not take their seat
without adjusting the seat's head restraint
correctly and adjusting and fastening the
seat belt.
Loading luggage or objects
behind the row 3 seat and
bench seat
If you want to load luggage onto the backrests
in row 3 while in the table position, the
backrests in row 2 must also be in the table
position.
Labels
When driving, carrying a passenger is
prohibited:
-

i
n row 3 if the backrest in front (row 2) is in
the table position.
-

i
n row 3 if the seat /bench in front (row 2) is
in the fully folded position.
-

i
n rows 2 and 3, in the outer right seat, if
the bench is in the fully folded position,
-

o
n the centre seat if the outer right seat is
in the fully folded position.
3
ease of use and comfort

110
Traveller-VP_en_Chap03_ergonomie-et-confort_ed01-2016
Mats
When fitting the mats for the first time, on the
driver's side use only the fixings provided in the
wallet attached.
FittingRemoval
To avoid any risk of jamming of the
pedals:
-

o
nly use mats which are suited to
the fixings already present in the
vehicle; these fixings must be used,
-

n
ever fit one mat on top of another.
The use of mats not approved by
P
e

ugeo
T m
ay inter fere with access to
the pedals and hinder the operation of
the cruise control / speed limiter.
The mats approved by P
e

ugeo
T h
ave
two fixings located below the seat.
To remove the mat on the driver's side:
F

m

ove the seat as far back as possible,
F

un
clip the fixings,
F

r

emove the mat.
Interior fittings
In rows 2 and 3
Refitting
To refit the mat on the driver's side:
F p osition the mat correctly,
F

r
efit the fixings by pressing,
F

c
heck that the mat is secured correctly.
us

e the Velcros to fit the transverse mats in
row
2 with the longitudinal mats in rows 2 and 3.
ease of use and comfort