2016 Peugeot Boxer remote control

20
boxer_en_Chap02_Pret-a-Partir_ed01-2015
Front doorSc hild lock
this prevents opening of the sliding side
door from the inside.
Press the control located on the edge of the

side door.u
se the corresponding button on the remote
control or use the key in the driver's door
lock barrel to unlock.
Pull the handle towards you.
SLIdInG SIdE door
take care not to obstruct the guide space
on the floor in order for the door to slide
correctly.
From outside
Pull the handle towards you then towards
the rear.
From inside
to unlock and open, push the handle
towards the rear.
e

nsure that the door opens fully in order
for the latch at the bottom of the door to
engage.
to release and close, pull the handle while


sliding the door.
Do not drive with the sliding side door
open.
Access

22
boxer_en_Chap02_Pret-a-Partir_ed01-2015
LocKInG / unLocKInG FroM InSIdEd oor open warning lamp
If this warning lamp comes on,
check that all of the doors and
the bonnet are closed correctly.
reversing camera
With the vehicle stationary, opening the rear
doors activates the camera and sends the
image to the screen fitted in the cab.
cab and load space
Pressing permits electric central
locking and unlocking, when the
doors are closed.
t

he doors can still be opened from the
inside.
If one of the doors is open or is not
closed correctly, the central locking
does not work.
t
he indicator lamp in the control:
Load space
Press to lock or unlock the side
door and rear doors from the cab.
t

he indicator lamp remains on
when locked
Anti-intrusion security
When the vehicle is started, the system
locks the cab and load space doors
automatically when you reach approximately
12 mph (20 km/h).
If none of the doors is opened during the
journey, the locking remains active.
Activation/deactivation of the system
t

he system setting is made with the M od E
button: in the "Autoclose" menu, select "ON"
or "OFF".
-

comes on when the doors


are locked and the ignition is
switched on,
-

then flashes when the doors


are locked when stationary
with the engine off.
t

he control is not active when the vehicle
has been locked using the remote control or
the key from the outside.
Good practice
If you decide to drive with the doors locked,
be aware that this could make access to the
vehicle by the emergency services more
difficult in an emergency. Refer to the "
t
echnology on board -

Vehicle configuration" section.
Access

38
boxer_en_Chap02_Pret-a-Partir_ed01-2015
IGnItIon SWItcH
StoP position: steering lock.
t
he ignition is off.
MA
r position: ignition on.
Certain accessories can be used.
AV V position: starter.
t

he starter is operated.
Starting the engine
Engine immobiliser warning lamp
If this warning lamp comes

on, use another key and have
the faulty key checked by a
P
euge O t
dealer
.
d

iesel pre-heating warning lamp
With the parking brake applied
and the gearbox in neutral, turn
the key to the MA
r position.
Wait for this warning lamp to go off then
operate the starter (AV V position) until the
engine starts.
t

he period of illumination of the warning
lamp depends on the climatic conditions.
d
oor or bonnet open warning
lamp
If this warning lamp comes on,

check that the doors and bonnet
are closed correctly.
Switching off the engine
Stop the vehicle and apply the parking
brake, then, with the engine at idle, return
the key to the S
to P position.
In low temperatures
In mountainous and/or cold areas, it is
advisable to use a "winter" type fuel suited
to low or minus temperatures.
Avoid attaching heavy objects to the
key or the remote control, which would
weigh down on its blade in the ignition
switch and could cause a malfunction.
It could adversely affect the deployment of
the front airbag. With the engine hot, the warning lamp comes
on for a few moments, you can start the engine
without waiting.
As soon as the engine is running, release the key.
Starting and switching off

258
boxer_en_Chap11_Particularites_ed01-2015
PrESEntAtI on
the tipper body is raised by a electro-hydraulic unit powered by the
vehicle's battery .
Raising and lowering the the tipper body done is by pressing and
holding the corresponding buttons on the magnetic and portable
remote control mounted on on a carrier in the cab.Power to raise the tipper body is generated by the motor in the electro-\
hydraulic unit.
The tipper body is lowered by an electrovalve that opens a fluid return from
the
ram.
A safety device prevents the tipper body from dropping when static or bei\
ng raised.
tipper body

3
2
READY TO GO
boxer-post-it_en_Chap02_Pret-a-Partir_ed01-2015
Starting and switching off
boxer-post-it_en_Chap02_Pret-a-Partir_ed01-2015
BATTERY STANDBY SYSTEM
If the vehicle is not to be used for a
prolonged period, such as for winter storage,
for example, it is strongly recommended that
the battery be placed on standby in order to
protect it and optimise its service life.
To place the battery on standby:
- Switch off the engine ( STOP position).
- Press the red button, then turn the key
to the BATT position.
The battery goes into standby about
7 minutes later.
This time is necessary to:
- Allow the user to get out of the vehicle
and lock the doors with the remote
control.
- Ensure that all of the vehicle's electrical
systems are deactivated.
When the battery is on standby,
access to the vehicle is only possible
by unlocking the vehicle using the key in the
lock barrel in the driver's door.
After placing the battery on standby,
settings (time, date, radio station
presets...) are memorised.
To take the battery out of standby:
- Turn the key to the MAR position.
- Start the engine normally ( AV V position).