2016 Peugeot 308 wheel bolts

220
308_en_Chap07_info-pratiques_ed02-2015
"Multimedia"
Multimedia support, hands-free kit, DVD player,
driving aids, vehicle tracking system, ...
Accessories
A wide range of accessories and genuine parts is available from the PeugeOt d ealer network.the
se accessories and parts are all suitable for your vehicle and benefit from Peu geOt's r ecommendation and warranty.
"Transport solutions"
Boot liners, roof bars, bicycle carrier on roof
bars, ski carrier, roof box, towbar harness, ...
tow b

ar, which mst be fitted by P
eu
ge
Ot
d

ealer or a qualified workshop.
Conversion kits
You can obtain an "ent erprise" kit to convert a
trade vehicle to a private car and vice-versa.
"Styling"
alloy wheels from 15 inch to 18 inch, finishers
for wheels, door sills, gear lever knobs, ...
"Ligne S": 16 and 17 inch alloy wheels, body
kit, stickers, interior and exterior mirror shells,
gear lever knob, door sills, mats*, …
"Comfort"
Door deflectors, side blinds and rear blind,
cigarette lighter, boot dividers, coat hanger
fixed to head restraint, front centre armrest,
under shelf storage, front and rear parking
sensors, styling mudflaps, window film, boot
management system, ...
*


t
o av
oid any risk of jamming of the pedals:
-
en

sure that the mat is positioned and
secured correctly,
-
ne

ver fit one mat on top of another.
"Security and safety"
Anti-theft alarm, window engraving, wheel
security bolts, child seats and booster
cushions, breathalyzer, first aid kit, warning
triangle, high visibility jacket, stolen vehicle
tracking system, temporary puncture repair kit,
snow chains, non-slip covers, front foglamps
kit, dog guard, ...
"Protection"
Mats*, seat covers compatible with lateral
airbags, mud flaps, side protection rubbing
strips, bumper protection rubbing strips,
bumper protectors, boot sill finishers, boot
mat,
...
Practical information

250
308_en_Chap08_en-cas-de-panne_ed02-2015
Changing a wheel
the tools are installed in the boot under the
f l o o r.
Access to the tooling
List of tools
these tools are specific to your vehicle and can
v ary according to the level of equipment. Do
not use them for other purposes.
1.
W

heelbrace.
Fo

r removing the wheel trim and removing
the wheel bolts.
2.
Ja

ck with integral handle.
Fo

r raising the vehicle. 3.
"B

olt cover" tool.
Fo

r removing the bolt protectors (covers)
on alloy wheels.
4.
So
cket for the security bolts (located in the
glove box).
Fo
r adapting the wheelbrace to the special
"security" bolts.
5.
tow
ing eye.
Procedure for changing a wheel with a damaged or punctured tyre for the spare wheel using the tools provided with the vehicle.
For more information on towing, refer to
the corresponding section.
Wheel with trim
When refitting the wheel, refit the trim
starting by placing its notch facing the
valve and press around its edge with
the palm of your hand.
In the event of a breakdown

252
308_en_Chap08_en-cas-de-panne_ed02-2015
F Remove the bolt cover from each of
t
he bolts using the tool 3 (according to
equipment).
F
Fi

t the security socket 4 on the
wheelbrace
1

to slacken the security bolt
(if
f

itted).
F
Sl

acken the other bolts using the
wheelbrace 1 o n l y. F Po
sition the foot of the jack on the ground,
ensuring that it is directly below the
vehicle's jacking point A or B , the one
closest to the wheel to be changed.
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not
block traffic: the ground must be level,
stable and not slippery.
Apply the parking brake unless it has
been programmed to automatic mode,
switch off the ignition and engage first
gear to block the wheels.
Check that the braking warning lamp
and the P warning lamp in the parking
brake control lever come on.
the o

ccupants must get out of the
vehicle and wait where they are safe.
Never go underneath a vehicle raised
using a jack; use an axle stand.
Do not use:
-
th

e jack for any other purpose than
lifting the vehicle,
-
a ja

ck other than the one supplied
by the manufacturer.
In the event of a breakdown

253
308_en_Chap08_en-cas-de-panne_ed02-2015
ensure that the jack is stable. If the ground is slippery or loose, the jack may slip or drop -
R isk of injury!
ens

ure that the jack is positioned only at one of the jacking points A or B under the vehicle,
making sure that the vehicle's contact sur face is centred on the head of the jack. Other wise
there is a risk of damage to the vehicle and/or of the jack dropping - Risk of injury! F
Re

move the bolts and store them in a clean
place.
F
Re
move the wheel.
F


e
xt
end the jack 2
until its head comes into contact with the jacking point A or B used, with the
contact sur face A or B on the vehicle correctly engaged with the central part of the head of the jack.
F
Rai
se the vehicle until there is sufficient space between the wheel and the ground to admit the
spare (not punctured) wheel easily.
8
In the event of a breakdown

254
308_en_Chap08_en-cas-de-panne_ed02-2015
Fitting a wheel
Fitting the "space-saver"
spare wheel
If your vehicle is fitted with alloy wheels,
when tightening the bolts on fitting, it
is normal to notice that the washers
do not come into contact with the
"space-saver" spare wheel.
the w

heel
is secured by the conical sur face of
each bolt. F
Pu

t the wheel in place on the hub.
F
Sc
rew in the bolts fully by hand.
F Pr e-tighten the security bolt using the
wheelbrace 1 fitted with the security
socket 4 (according to equipment).
F
Pr

e-tighten the other bolts using the
wheelbrace 1 o n l y. F
Lo

wer the vehicle fully.
F
Fo
ld the jack 2 and detach it.
In the event of a breakdown

255
308_en_Chap08_en-cas-de-panne_ed02-2015
F tighten the security bolt using the
w heelbrace 1 fitted with the security
socket
4

(according to equipment).
F


t
ig
hten the other bolts using the
wheelbrace 1 o n l y.
F
Re

fit the bolt covers on each of the bolts
(according to equipment).
F
St

ore the tools in the box.
the t
yre inflation pressures are given on
this
lab

el.
After changing a wheel
to store the punctured wheel in the boot
c orrectly, first remove the central cover.
When using the "space-saver" type
spare wheel, do not exceed 50 mph
(80
k

m/h).
Have the tightening of the bolts and the
pressure of the spare wheel checked
by a P
eu

ge
Ot d
ealer or a qualified
workshop without delay.
Have the punctured wheel repaired
and refitted to the vehicle as soon as
possible.
If your vehicle has tyre under-inflation
detection, check the tyre pressures then
refer to the corresponding section.
8
In the event of a breakdown