2016 Peugeot 308 engine

60
308_en_Chap02_ouvertures_ed02-2015
When unlocking of the boot only is activated:
F With the electronic key in the recognition
zone A , press the boot unlocking control
to unlock just the tailgate, then raise the
tailgate.
unl

ocking is signalled by rapid flashing of the
direction indicators for a few seconds.
use t

his button for access to
additional information.
Closing
F Lower the tailgate using one of the interior
g rab handles.
If the boot is not closed correctly (the lock has
two positions): with the engine running or
when moving (speed above 6 mph (10 km/h)),
a message appears for a few seconds.
Tailgate release
Unlocking
F Fold back the rear seats to gain access to
t he lock from inside the boot.
F
In

sert a small screwdriver into hole A of the
lock to unlock the tailgate.
F
Mov

e the latch to the right.
Locking after closing
If the fault persists after closing again, the boot
will remain locked.System allowing the mechanical unlocking
of the boot in the event of a battery or central
locking system malfunction.
F
Wi

th the electronic key in the recognition
zone A , press the boot locking control to
lock the vehicle.
Locking is signalled by rapid flashing of the
direction indicators for a few seconds.
Locking with Keyless Entry
and Starting
Access

63
308_en_Chap02_ouvertures_ed02-2015
Lost keys, remote control, electronic key
Visit a PeugeOt dealer with the vehicle's registration certificate, your personal identification documents and if possible, the label bearing the
key code.
the Peu

ge
Ot d
ealer will be able to retrieve the key code and the transponder code required to order a new key
Remote control
the high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a possibility that it may unlock the
v ehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and out of sight of your vehicle. You run the risk of stopping it from
working and the remote control would have to be reinitialised.
the r

emote control does not operate when the key is in the ignition, even when the ignition is switched off.
Locking the vehicle
Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult in an emergency.
As a safety precaution (with children on board), remove the key from the ignition or take the electronic key when you leave the vehicle, even for
a short time.
Electrical interference
the Keyless ent ry and Starting electronic key may not operate if close to certain electronic devices: telephone, laptop computer, strong
magnetic fields, ...
Anti-theft protection
Do not make any modifications to the electronic engine immobiliser system; this could cause malfunctions.
Don't forget to turn the steering to engage the steering lock.
When purchasing a second-hand vehicle
Have the key codes memorised by a Peu geOt d ealer, to ensure that the keys in your possession are the only ones which can start the vehicle.
2
Access

73
308_en_Chap03_ergonomie-et-confort_ed02-2015
electric driver's seat
Forwards-backwardsSeat backrest angleSeat cushion height and
angle
to avoid discharging the battery, carry out
t hese adjustments with the engine running.
F Push the control for wards or rear wards to
sl ide the seat. F
til t the control for wards or rear wards to
adjust the angle of the seat backrest. F
tip t he rear of the control upwards or
downwards to obtain the desired height.
F


t
ip t
he front of the control upwards or
downwards to obtain the desired angle.
Before moving the seat backwards, ensure that there is nothing that might prevent the full
travel of the seat, so as to avoid the risk of of jamming the seat caused by the presence of
objects on the floor behind the seat or rear passengers. If the seat jams, stop the movement
immediately.
3
ease of use and comfort

74
308_en_Chap03_ergonomie-et-confort_ed02-2015
System which registers the electrical settings
of the driver's seat and the door mirrors.
You can store and recall two positions using
the buttons on the side of the driver's seat.
Storing driving positions
Storing a position
Using buttons M / 1 / 2
F Switch on the ignition.
F Ad just your seat and the door mirrors.
F
Pr

ess button M , then press button 1 or 2
within four seconds.
An audible signal indicates that the position has
been stored.
Storing a new position cancels the previous
position.
Recalling a stored position
Ignition on or engine running
F Press button 1 or 2 to recall the
c orresponding position.
An audible signal confirms that adjustment is
complete.
You can interrupt the current movement by
pressing button M , 1 or 2 or by using one of the
seat controls.
A stored position cannot be recalled while
driving.
Recalling stored positions is deactivated
45
s

econds after switching off the ignition.
ease of use and comfort

75
308_en_Chap03_ergonomie-et-confort_ed02-2015
Heated seats control
0: Of f.
1 : Low.
2 : Medium.
3 : High.
F


u
se t
he adjustment wheel to switch on and
select the level of heating required:
With the engine running, the front seats can be
heated separately.
F
to ra
ise the head restraint, pull it upwards.
F


t
o re

move the head restraint, press the
lug
A

and pull the head restraint upwards.
F
to put the head restraint back in place, engage
t he head restraint stems in the openings
keeping them in line with the seat back.
F to lower the head restraint, press the lug A
a nd the head restraint at the same time.
the h
ead restraint is fitted with a frame
with notches which prevents it from
lowering; this is a safety device in case
of impact.
The adjustment is correct when the
upper edge of the head restraint is
level with the top of the head.
Never drive with the head restraints
removed; they must be in place and
adjusted correctly.
Head restraint height
Additional adjustments
3
ease of use and comfort

76
308_en_Chap03_ergonomie-et-confort_ed02-2015
Electric lumbar adjustment
You can deactivate the massage
function at any time by pressing this
switch, its indicator lamp goes off.
Deactivation
Activation
Massage function
this system provides the occupants of the front
s eats with a lumbar massage. It only operates
when the engine is running or in S
tOP m

ode of
the Stop & Start system.
F
Pr

ess this switch.
Its indicator lamp comes on and the massage
function is activated for a period of 1 hour.
During this time, massage is per formed in
6 cycles of 10 minutes (6 minutes of massage
followed by 4 minutes break).
After one hour, the function is deactivated, the
indicator lamp goes off.
Adjustment of intensity
Press this button to adjust the
intensity of the massage.
two l
evels of massage are available.
F
Pr

ess the control to obtain the desired
lumbar support.
ease of use and comfort

80
308_en_Chap03_ergonomie-et-confort_ed02-2015
Interior fittings
1. Cooled glove box through a ventilation nozzle, if open,
engine running and air conditioning on.
2.
12 V a

ccessory socket (120 W)

Ob

serve the maximum power rating to
avoid damaging your accessory
3.
uSB p

ort
4.
Ja

ck auxiliary socket
5.
Cu

p holder (depending on version)
6.
Sto

rage (depending on version)
7.
Sto

rage - Retractable cup holder
tur

n the carrier for access to the cup
h o l d e r.
8.
Fro

nt armrest
9.
23

0 V (120 W) accessory socket
Ob

serve the power rating to avoid
damaging your accessory.
ease of use and comfort

84
308_en_Chap03_ergonomie-et-confort_ed02-2015
230 V / 50 Hz power socket
A 230 V / 50 Hz socket (maximum power:
120 W) is fitted in the rear storage box.
thi

s socket works with the engine running, as
well as in S
tOP m

ode with Stop & Start.
F
Op

en the central storage box,
F
Ch

eck that the warning lamp is on green,
F
Co

nnect your multimedia or other electrical
device (telephone charger, laptop
computer, CD-DVD player, baby food
warmer...).
In the event of a fault with the socket, the green
warning lamp flashes.
Have it checked by a P
eu

ge
Ot d
ealer or a
qualified workshop. Connect only one device at a time to
the socket (no extension or multi-way
connector).
Connect only devices with class II
insulation (shown on the device).
Do not use a device with a metal case.
As a safety measure, when electrical
consumption is high and when required
by the vehicle's electrical system
(particular weather conditions, electrical
overload...), the current supply to the
socket will be cut off; the green warning
lamp goes off.
the d

ifferent "ports and sockets" can
be either not available, an option or
standard, depending on the trim level of
the vehicle.
ease of use and comfort