2016 Peugeot 301 warning

21
301_en_Chap01_controle-de-marche_ed01-2016
Warning / indicator lamp State Cause Action / Observations
AdBlue
® additive
(BlueHDi Diesel) fixed, on switching
on the ignition,
accompanied by an
audible signal and a
message indicating the
remaining driving range. The remaining driving range is
between 350 miles (600 km) and
1500 miles (2400 km).
Have the AdBlue® additive tank topped up as soon
as possible: go to a PEUGEOT dealer or a qualified
workshop, or carry out this operation yourself.
+ flashing associated with
the SERVICE warning
lamp, accompanied by
an audible signal and a
message indicating the
remaining driving range.The remaining driving range is
between 0 and 350 miles (600 km).
You must top-up the AdBlue
® additive tank to avoid
a breakdown : go to a PEUGEOT dealer or a qualified
workshop, or carry out this operation yourself.
flashing, associated
with the SERVICE
warning lamp,
accompanied by an
audible signal and a
message indicating that
starting is prevented. The AdBlue
® tank is empty: the
starting inhibition system required
by legislation prevents starting of the
engine. To be able to start the engine, you must top-up the
AdBlue® additive tank: go to a PEUGEOT dealer
or a qualified workshop, or carry out this operation
yourself.
It is essential to add at least 3.8 litres of AdBlue
® to
the additive tank.
For topping-up or for more information on the AdBlue
® additive, refer to the corresponding section.
1
Monitoring

22
Warning / indicator lamp State Cause Action / Observations
+
+ SCR emissions
control system

(BlueHDi Diesel) fixed, on switching
on the ignition,
associated with the
SERVICE and engine
diagnostic warning
lamps, accompanied
by an audible signal
and a message. A fault with the SCR emissions
control system has been detected.
This alert disappears once the exhaust emissions
return to normal levels.
flashing, on switching
on the ignition,
associated with the
SERVICE and engine
diagnostic warning
lamps, accompanied by
an audible signal and
a message indicating
the remaining driving
range. After confirmation of the fault with the
emissions control system, you can
drive for up to 650 miles (1 100 km)
before the engine starting inhibition
system is triggered.
Contact a PEUGEOT dealer or a qualified workshop
without delay
, to avoid a breakdown .
flashing, on switching
on the ignition,
associated with the
SERVICE and engine
diagnostic warning
lamps, accompanied
by an audible signal
and a message. You have exceeded the authorised
driving limit following confirmation
of a fault with the emissions control
system: the engine starting inhibition
system prevents starting of the
engine.
To be able to start the engine, you must
call on a
PEUGEOT dealer or a qualified workshop.
Monitoring

24
Service overdue
For 5 seconds after the ignition is switched on,
the spanner flashes to indicate that the service
must be carried out as soon as possible.
Example: the service is overdue by 186 miles
(3 0 0 k m).
For 5 seconds after the ignition is switched on,
the screen indicates:
For BlueHDi Diesel versions, this alert
may also be accompanied by the fixed
illumination of the service warning lamp
when the ignition is on. Following this operation, if you wish to
disconnect the battery, lock the vehicle
and wait at least five minutes for the
zero reset to be taken into account.
Service indicator zero reset
After each service, the service indicator must
be reset to zero.
The procedure for resetting to zero is as
follows:
F

s
witch off the ignition,
F

p
ress and hold the trip distance recorder
zero reset button,
F

s
witch on the ignition; the distance recorder
display begins a countdown,
F

w
hen the display indicates "=0" , release
the button; the spanner disappears.
5 seconds after the ignition is switched on,
the distance recorder resumes its normal
operation. The spanner remains on
.The distance remaining may be
weighted by the time factor, depending
on the driving conditions.
Therefore, the spanner may also come
on if you have exceeded the period
since the last service, indicated in the
manufacturer's service schedule.
For BlueHDi Diesel versions, the
spanner may also be brought on earlier
than expected, depending on the
degree of deterioration of the engine oil
(depending on the country of sale).
The rate of deterioration of the engine
oil depends on the driving conditions in
which the vehicle is used.
Monitoring

29
301_en_Chap01_controle-de-marche_ed01-2016
Monochrome screen C (Audio system / Bluetooth)
This displays the following information:
- time,
-


date,
-

a
mbient temperature (this flashes if there is
a risk of ice),
-

s
tatus of doors and boot,
-
par

king sensors,
-

a
udio sources (radio, CD, USB port, jack
socket...),
-

t
rip computer (refer to the "Instruments and
controls" section).
Warning or information messages may appear
temporarily. These can be cleared by pressing
the " BACK " button. From your Audio system
/ Bluetooth control
panel, you can press:
F
the "MENU" button to gain access to the
main menu ,
F
the "MODE" button to select the display
of information in "Full screen" or "New
window" mode,
F

t
he "7" or " 8" buttons to navigate in a list,
F

p
ress the central button to confirm,


or
F

t
he "BACK " button to abandon the
operation in progress or go back up one
level in the menu.
Displays in the screen Controls
F Press the "MENU" button to gain access
to the main menu :
-
"Multimedia",
-


"Telephone",
-

"
Trip computer",
-
"

Bluetooth connection",
-


"Personalisation-configuration",
F

P
ress the " 7" or " 8" buttons to select the
menu required, then confirm by pressing
the centre button.
Main menu
1
Monitoring

35
301_en_Chap02_ouvertures_ed01-2016
If the problem persists, contact a
PEUGEOT dealer as soon as possible.
If the battery is flat, you are
informed by illumination of this
warning lamp, an audible signal
and a message in the screen.
Changing the battery
F Remove the flat battery from its location.
F
F it the new battery into its location
observing the original direction of fitment.
F

C
lip the cover onto the casing.
In the event of a fault with the remote control,
you can no longer unlock, lock or locate
your


vehicle.
F

F

irst of all, use the key in the lock to unlock
or lock your vehicle.
F

T

hen, reinitialise the remote control.
Fault with the remote
control
Reinitialisation
F Switch off the ignition and remove the
ignition key.
F

P
ress the closed padlock immediately for a
few seconds.
F

T
urn the key to position 2 (Ignition on) .
F

S
witch off the ignition and remove the key
from the ignition switch.
The remote control is fully operational again. Battery ref.: CR2032 / 3 volts.
F

U
nclip the cover using a small screwdriver
at the cutout.
F

L
ift off the cover.
2
Access

39
301_en_Chap02_ouvertures_ed01-2016
Doors
From outside
F After unlocking the vehicle using the remote control or the key, pull the door
handle.
Opening
From inside
F Pull the interior control lever of a front door; this unlocks the vehicle completely. -

w
hen the engine is running
,
this warning lamp comes on,
accompanied by a message in
the multifunction screen for a
few

seconds,
-
w
hen the vehicle is moving (speed
higher than 6 mph (10 km/h)), this warning
lamp comes on, accompanied by an
audible signal and a message in the
multifunction screen for a few seconds.
Closing
When a door is not closed correctly:
Secondary control
For mechanically locking and unlocking the
doors in the event of a fault with the central
locking system or a battery failure.
Driver's door
Insert the key in the lock to lock or unlock
the door.
Passenger doors
F On the rear doors, check that the child lock is not on.
F

R
emove the black cap located on the edge
of the door, using the key.
F

I
nsert the key into the aperture without
forcing, then without turning, move the
latch sideways towards the inside of
the


door.
F

R
emove the key and refit the cap.
2
Access

40
301_en_Chap02_ouvertures_ed01-2016
Boot
Opening
Unlocking and releasing the boot
using the remote control
F Press the centre button on the remote control for more than
one


second.
The boot lid is released and opens
s li g ht l y.
Releasing the boot from the
inside
Opening the boot
F Raise the boot lid to its fully open position.
F

L
ower the boot lid using one of the interior
grab handles.
Closing
Electric boot opening
- when the engine is running , this warning lamp comes on,
accompanied by a message in the
multifunction screen for a few seconds,
- when the vehicle is moving (speed above
6 mph (10 km/h)), this warning lamp comes
on, accompanied by an audible signal and
a message in the multifunction screen for a
few seconds.
F

P

ress the boot opening switch located
on the left of the dashboard (electric boot
opening).


or
Mechanical boot opening
There is no associated warning for the boot lid
not being fully closed.
You should ensure that the boot is closed
c o r r e c t l y. If the boot is not closed correctly:
F

Ra

ise the control lever below the driver's
door (mechanical boot opening).
The boot lid is released and opens slightly.
Access

42
301_en_Chap02_ouvertures_ed01-2016
Windows
Electric controls Manual controls
The electric window switches remain
operational for about 45 seconds after
switching off the ignition or until a front
door is opened. During this period of
45 seconds, if you open a door while
operating a window, the window stops.
Operating the switch again has no
effect until the ignition is switched on
again.Always remove the key from the ignition
when leaving the vehicle, even for a
short time.
In the event of contact during operation
of the windows, you must reverse the
movement of the window. To do this,
press the switch concerned.
When operating the passenger electric
window switches, the driver must
ensure that no one is preventing correct
closing of the windows.
The driver must ensure that the
passengers use the electric windows
c o r r e c t l y.
Be particularly aware of children when
operating the windows.
1.
Le

ft hand front electric window.
2.
R

ight hand front electric window.
3.
R

ight hand rear electric window.
4.
Le
ft hand rear electric window.
5.
D

eactivating the rear electric window
switches .
To open or close the window, press or pull the
switch. The window stops as soon as the switch
is released.
Turn the window winder located on the door
trim panel.
Deactivating the rear window
controls
For the safety of your children, press switch 5
t o prevent operation of all of the windows,
irrespective of their position.
With the warning lamp on, the switches are
deactivated. With the warning lamp off, the
switches are active.
Model with front electric windows
Model with front and rear electric windows
Access