2016 NISSAN JUKE heater


> (GLW    0RGHO )' @
4-42Heater, air conditioner, audio and phone systems
Specification chart (for models with navigation system):GUID-F83C168B-173D-4313-B631-F712588C0463
Supported mediaCD, CD-R, CD-RW
Supported file systems ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not
supported.
Supported
versions*1 MP3
Version
MPEG1, MPEG2, MPEG2.5
Sampling frequency 8 kHz - 48 kHz
Bit rate 8 kbps - 320 kbps, VBR
WMA*2 Version
WMA7, WMA8, WMA9
Sampling frequency 32 kHz - 48 kHz
Bit rate 48 kbps - 192 kbps, VBR
Tag information ID3 tag VER1.0, VER1.1, VER2.2, VER2.3 (MP3 only)
Folder levels Folder levels: 8, Max folders: 255 (including root folder) , Files: 512 (Max. 255 files for one folder)
Text character number limitation 128 characters
Displayable character codes*2 01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian) , 04: UNICODE (UTF-16 Non-BOM Big
Endian) , 05: UNICODE (UTF-8) , 06: UNICODE (Non-UTF-16 BOM Little Endian)
*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.
*2 Available codes depend on what kind of media, versions and information are going to be displayed.
&RQGLWLRQ


> (GLW    0RGHO )' @
Troubleshooting guide:GUID-F83C168B-173D-4313-B631-F712588C0463
SymptomCause and Countermeasure
Cannot play Check if the disc or USB device was inserted correctly.
Check if the disc is scratched or dirty.
Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player.
If there is a temperature increase error, the CD player will play correctly after it returns to the normal temperature.
If there is a mixture of music CD files (CD-DA data) and MP3/WMA files on a CD, only the music CD files (CD-DA data) will be
played.
Files with extensions other than ª.MP3º, ª.WMAº, ª.mp3º or ª.wmaº cannot be played. In addition, the character codes and number of
characters for folder names and file names should be in compliance with the specifications.
Check if the finalization process, such as session close and disc close, is done for the disc.
Check if the disc or USB device is protected by copyright.
Poor sound quality Check if the disc is scratched or dirty.
Bit rate may be too low.
It takes a relatively long time before
the music starts playing. If there are many folders or file levels on the MP3/WMA disc, or if it is a multisession disc, or USB device, some time may be required
before the music starts playing.
Music cuts off or skips The writing software and hardware combination might not match, or the writing speed, writing depth, writing width, etc., might not
match the specifications. Try using the slowest writing speed.
Skipping with high bit rate files Skipping may occur with large quantities of data, such as for high bit rate data.
Move immediately to the next song
when playing When a non-MP3/WMA file has been given an extension of ª.MP3º, ª.WMAº, .ªmp3º or ª.wmaº, or when play is prohibited by
copyright protection, there will be approximately 5 seconds of no sound and then the player will skip to the next song.
Songs do not play back in the
desired order The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired
order.
Heater, air conditioner, audio and phone systems4-43
&RQGLWLRQ


> (GLW    0RGHO )' @
4-44Heater, air conditioner, audio and phone systems
Bluetooth


> (GLW    0RGHO )' @
4-46Heater, air conditioner, audio and phone systems
Balance adjusts the sound between the left
and right speakers. Fade adjusts the sound
between the front and rear speakers.
Select the ªBassº, ªTrebleº, ªBalanceº or
ªFadeº using the TUNE´FOLDER knob, and
then push the ENTER/SETTING button.
Turn the TUNE´FOLDER knob to adjust the
Bass, Treble, balance and Fade of the
screen to the preferred level. Push the
ENTER/SETTING button to apply the
setting.
. Speed Sensitive Vol.
To change the Speed Sensitive Volume
(Speed Sensitive Vol.) level from off (0) to
5, turn the TUNE´FOLDER knob.
. AUX Vol.
Controls the volume level of incoming sound
when an auxiliary device is connected to the
system. Choose a setting between +1 and
+3 or choose 0 to disable the feature
entirely.
. Brightness and Contrast
Adjust the brightness and contrast of the
screen.
Select ªBrightnessº or ªContrastº using the
TUNE´FOLDER knob and then push the
ENTER/SETTING button. Turn the
TUNE´FOLDER knob to adjust the bright-
ness and contrast of the screen to the preferred level. Push the ENTER/SETTING
button to apply the setting.
. Clock Adjust
Adjust the clock according to the following
procedure.
1) Select ªClock Adjustº using the
TUNE´FOLDER knob and then push
the ENTER/SETTING button.
2) Adjust the hour with the TUNE´FOLDER knob and then push the ENTER/
SETTING button.
3) Adjust the minute with the TUNE´FOLDER knob and then push
the ENTER/SETTING button.
24 hour clock is not available.
. On-Screen Clock
When this item is turned on, a clock is
always displayed in the upper right corner of
the screen.
Select the ªOn-Screen Clockº using the
TUNE´FOLDER knob and then push the
ENTER/SETTING button. You can toggle
between ON and OFF using the
TUNE´FOLDER knob.
. RDS Display (if so equipped)
RDS (radio data system) information can be
shown on the display. Select ªRDS Displayº
using the TUNE´FOLDER knob and then
push the ENTER/SETTING button. You can toggle between ON and OFF using the
TUNE´FOLDER knob. Push the ENTER/
SETTING button to apply the setting.
. Language Select
The language settings can be changed.
Select ªLanguage Selectº using the
TUNE´FOLDER knob and then push the
ENTER/SETTING button. Use the
TUNE´FOLDER knob to select the preferred
language. Push the ENTER/SETTING but-
ton to apply the setting.
DISP button:GUID-F83C168B-173D-4313-B631-F712588C0463Display of the screen can be canceled by
pushing the
button. You can still listen to
music that is being played back even while the
screen display is turned off. If you want to
display the screen again, push the
button
once more. Pushing some of the audio source
buttons will also turn the screen back on and
display the screens of the corresponding
sources.
MEDIA button:GUID-F83C168B-173D-4313-B631-F712588C0463Pushing thebutton will switch the audio
source as follows:
USB/iPod ?Bluetooth Audio ?AUX ?USB/
iPod
&RQGLWLRQ


> (GLW    0RGHO )' @
Apps button:GUID-F83C168B-173D-4313-B631-F712588C0463Thebutton launches the Smartphone
Integration mode. See ªNissanConnectSMApp
smartphone integrationº (P.4-75) .
FM-AM Radio operationGUID-F6D3CBA1-CE19-4A9D-8F43-C15C732220C2
radio (FM´AM) band select:GUID-F83C168B-173D-4313-B631-F712588C0463Push thebutton to change the band as
follows:
AM ?FM1 ?FM2? AM
TUNE (Tuning):
GUID-F83C168B-173D-4313-B631-F712588C0463Turn the TUNE´FOLDER knob for manual tuning.
SEEK tuning:GUID-F83C168B-173D-4313-B631-F712588C0463Push theorbutton to tune from low to
high or high to low frequencies and to stop at
the next broadcasting station.
SCAN tuning:GUID-F83C168B-173D-4313-B631-F712588C0463Push thebutton to tune from low to high
frequencies and stop at each broadcasting
station for several seconds. Pushing the button
again during this several seconds period will
stop SCAN tuning and the radio will remain
tuned to that station. If the
button is not pushed within this
period, SCAN tuning moves to the next station.
toRadio memory buttons:GUID-F83C168B-173D-4313-B631-F712588C0463Up to 12 stations can be set for the FM band (6
each for FM1 and FM2) and 6 stations can be
set for the AM band.
1. Choose the radio band using the
button.
2. Tune to the desired station.
3. Push and hold the desired station preset button
tountil beep sounds.
4. The station indicator will then come on. The station is now set to the button memory.
5. Other buttons can be set in the same
manner.
If the battery cable is disconnected, or if the fuse
opens, the station memory will be erased. In that
case, reset the desired stations.
CD player operationGUID-248E139A-04E4-4AD2-8E33-2281B71D316APlace the ignition switch in the ON or ACC
position. Insert the Compact Disc (CD) into the
slot with the label side facing up. The CD will be
guided automatically into the slot and start
playing.
After loading the CD, the number of tracks on
the CD and the play time will appear on the
display.
If another audio source is already operating, it
will automatically turn off and the CD will play.
If the system has been turned off while the CD
was playing, pushing the Power button will start
the CD.
CD PLAY:GUID-F83C168B-173D-4313-B631-F712588C0463When the CD button is pushed while a CD is
loaded, the CD will start playing.
SEEK TRACK:GUID-F83C168B-173D-4313-B631-F712588C0463When theorbutton is pushed and hold
while the CD is being played, the CD will play
while fast forwarding or rewinding. When the
button is released, the CD will return to normal
play speed.
When the
orbutton is pushed while
the CD is being played, the next track or the
beginning of the current track on the CD will be
Heater, air conditioner, audio and phone systems4-47
&RQGLWLRQ


> (GLW    0RGHO )' @
4-48Heater, air conditioner, audio and phone systems
played. Push thebutton again to select the
previous track.
REPEAT (RPT):GUID-F83C168B-173D-4313-B631-F712588C0463When the RPT button is pushed while the CD is
played, the play pattern can be changed as
follows:
(CD)
(Normal) Û1 Track Repeat
(CD with compressed audio files)
(Normal) ?1 Folder Repeat ?1 Track Repeat
? (Normal)
RANDOM (RDM):GUID-F83C168B-173D-4313-B631-F712588C0463When the RDM button is pushed while a CD is
being played, the play pattern can be changed
as follows:
(CD)
(Normal) Û1 Disc Random
(CD with compressed audio files)
(Normal) ?1 Disc Random ?1 Folder
Random ?(Normal)
CD eject:GUID-F83C168B-173D-4313-B631-F712588C0463When the CD eject button is pushed with the
CD loaded, the CD will be ejected.
When this button is pushed while the CD is being played, the CD will be ejected.
If the CD comes out and is not removed, it
will be pulled back into the slot to protect
it.
USB (Universal Serial Bus) connection
port
GUID-9EC1B306-00B9-45B0-A5FF-A3892E5A43EF
WARNING
Do not connect, disconnect or operate
the USB device while driving. Doing so
can be a distraction. If distracted you
could lose control of your vehicle and
cause an accident or serious injury.
CAUTION
.
Do not force the USB device into the
USB port. Inserting a USB device
tilted or upside-down into the port
may damage the port. Make sure
that the USB device is connected
correctly to the USB port.
. Do not grab the USB port cover (if
so equipped) when pulling a USB
device out of the port. This could
damage the port and the cover. .
Do not leave a USB cable in a place
where it can be pulled unintention-
ally. Pulling the cable may damage
the port.
Refer to your device manufacturer's owner
information regarding the proper use and care
of the device.
&RQGLWLRQ


> (GLW    0RGHO )' @
4-50Heater, air conditioner, audio and phone systems
CAUTION
.Do not force the USB device into the
USB port. Inserting the USB device
tilted or up-side-down into the port
may damage the port. Make sure
that the USB device is connected
correctly into the USB port.
. Do not grab the USB port cover (if
so equipped) when pulling the USB
device out of the port. This could
damage the port and the cover.
. Do not leave the USB cable in a
place where it can be pulled unin-
tentionally. Pulling the cable may
damage the port.
Refer to your device manufacturer's owner
information regarding the proper use and care
of the device.
Connecting iPod


> (GLW    0RGHO )' @
4-52Heater, air conditioner, audio and phone systems
JVH0620X
2. Select ªBluetoothº .
3. Select ªAdd Phone or Deviceº . This samescreen can be accessed to remove, replace
or select a different Bluetooth