2016 MITSUBISHI SHOGUN transmission

•Check the brake system and, if neces-
sary, have it serviced.
• Check the engine, transmission, trans-
fer, and differential oil or grease level and turbidity. If the oil or grease is
milky, it indicates water contamina-
tion. Replace it with new oil or grease.
• Grease the propeller shaft.
• Check the inside of the vehicle. If in-
gress of water is found, dry the carpet
etc.
• Inspect the headlamps. If the head-
lamp bulb is flooded with water, we
recommend you to have it drained.Cautions on handling of 4-
wheel drive vehicles E00606800401
Tyres and wheels
Since the driving torque can be applied to the
4 wheels, the performance of the vehicle when operating in 4-wheel drive is greatly af- fected by the condition of the tyres.

Pay close attention to the tyres.
l Install specified tyres on all wheels. Re-
fer to “Tyres and wheels” on page
11-11.
l Be sure to fit all 4 tyres and wheels of
the same size and type.
When replacement of any of the tyres or
wheels is necessary, replace all of them.
l All tyres should be rotated whenever the
wear difference between the front and
rear tyres is recognizable.

Good vehicle performance cannot be expec- ted if there is a difference in wear between
tyres. Refer to “Tyre rotation” on page 10-15.
l Check the tyre inflation pressure regular-
ly.
l If the tyre inflation pressure is inappro-
priate, the transfer gear may make some
noise and shock while changing the drive mode.CAUTIONl Always use tyres of the same size, same
type, and same brand, and which have no wear differences. Using tyres which differ in
size, type, brand or the degree of wear will
cause excessive loading, resulting in possi- ble damage to the drive system.Towing
If towing is necessary, we recommend you to
have it done by your MITSUBISHI
MOTORS Authorized Service Point or a
commercial tow truck service.
In the following cases, transport the vehicle
using a tow truck.
l The engine runs but the vehicle does not
move or abnormal noise is produced.
l Inspection of the vehicle’s underside re-
veals that oil or some other fluid is leak- ing.
Only when you cannot receive a towing serv- ice from a MITSUBISHI MOTORS Author-
ized Service Point or commercial tow truck
service, tow your vehicle carefully in accord- ance with the instructions given in “Towing”
on page 8-16.Cautions on handling of 4-wheel drive vehicles
6-38OVWE16E1Starting and driving6

CAUTIONlBe sure to shift the transfer shift lever to the
“2H” position. Never try to tow with the transfer shift lever in the “4H”, “4HLc” or
“4LLc” positions and with any of the wheels
on the ground (Type A or B). This could re- sult in damage to the vehicle’s driving sys- tem, or the vehicle could become separated from the tow truck and unexpected accident
might result. If you cannot shift the transfer shift lever to “2H” position or the transmis-
sion is malfunctioning or damaged, transport the vehicle with all the wheels on a carriage (Type C or D) as illustrated.If you can shift the transfer shift lever to the “2H” position.If you cannot shift the transfer shift lever to the “2H”
position.
Jacking up a 4-wheel drive ve-
hicle
WARNINGl Do not crank the engine while jacking up
the vehicle.
The tyre on the ground may turn and the
vehicle may roll off the jack.Clutch operation
Quick or slight clutch engagement made
while the engine is running at high speed will
cause damage to the clutch and transmission because the tractive force is very great.
Operate the pedal slowly and positively.
Braking
E00607001524
All the parts of the brake system are critical
to safety. We recommend you to have the ve- hicle checked at regular intervals according
to the service booklet.
CAUTIONl Avoid driving habits that cause heavy brak-
ing and never “ride” the brakes by resting
your foot on the brake pedal while driving.
It causes brake overheating and fade.
Brake system
The service brake is divided into two brake
circuits so that when one brake circuit fails, the other is available to stop the vehicle. In
this situation, even if the brake pedal moves down to the very end of its possible stroke,
keep depressing the brake pedal down harder than usual; stop driving as soon as possible
and have the brake system repaired.
Braking
6-39OVWE16E1Starting and driving6

The regulations concerning towing may dif-
fer from country to country. It is recommen-
ded that you obey the regulations of the area where you are driving your vehicle.Towing the vehicle by a tow
truckCAUTIONl This vehicle must not be towed by a tow
truck using sling lift type equipment (Type A) as illustrated. Using a sling lift will dam-age the bumper and front end.
l Be sure to shift the transfer shift lever to
“2H” position and transport the vehicle with the driving wheels on a carriage (Type C, D
or E) as illustrated. Never try to tow with the transfer shift lever in “4H”, “4HLc” or “4LLc” positions and with the front or rearwheels on the ground (Type B or Type C) as illustrated. This could result in driving sys-
tem damage or the vehicle may jump at the
carriage. If you cannot shift the transfer shift lever to the “2H” position or the transmis-sion is malfunctioning or damaged, transport the vehicle with all wheels on a carriage
(Type D or E) as illustrated.
l As your vehicle equipped with the Active
Stability & Traction Control system (ASTC), if the vehicle is towed with the ig-
nition switch in the “ON” position and only
the front wheels or only the rear wheels raised off the ground, the active Traction
Control System may operate, resulting in an accident.CAUTIONl If you tow vehicles with
A/T with the driv-
ing wheels on the ground (Type B) as illus-
trated, make sure that the towing speed and distance given below are never exceeded, causing damage to the transmission.

Petrol-powered vehicles
Towing speed: 50 km/h (31 mph)
Towing distance: 50 km (31 miles)

Diesel-powered vehicles
Towing speed: 30 km/h (19 mph)
Towing distance: 80 km (50 miles)

For the towing speed and the towing dis- tance, follow the local driving laws and reg-
ulations.
Towing with front wheels off
the ground (Type B)
Place the gearshift lever in the “N” (Neutral) position ( M/T) or the selector lever in the
“N” (NEUTRAL) position (A/T).
Release the parking brake.
CAUTIONl Never tow an
A/T vehicle with the front
wheels up (and the rear wheels on the ground) (Type B) when the A/T fluid level islow. This may cause serious and expensive
damage to the transmission.
Towing
8-17OVWE16E1For emergencies8

both vehicles, and that the vehicles trav-
el at low speed.CAUTIONl Avoid sudden braking, sudden acceleration
and sharp turning; such operation could
cause damage to the towing hooks or the tow
rope.
People in the vicinity could be injured as a
result.
l When towing or being towed down a long
slope, the brakes may overheat reducing the effectiveness. In this situation, have your ve-hicle transported by a tow truck.
l When the vehicle with
A/T is to be towed by
another vehicle with all the wheels on the
ground, make sure that the towing speed and
distance given below are never exceeded, avoiding damage to the transmission.

Petrol-powered vehicles
Towing speed: 50 km/h (31 mph)
Towing distance: 50 km (31 miles)

Diesel-powered vehicles
Towing speed: 30 km/h (19 mph)
Towing distance: 80 km (50 miles)

For the towing speed and the towing dis- tance, follow the local driving laws and reg-
ulations.If your vehicle tows another ve-
hicle
Only use the rear towing hook as shown in
the illustration. Secure the tow rope to the rear towing hook.
CAUTIONl When you are going to tow another vehicle,
move the transfer shift lever to “4H” posi-
tion.
Selecting “2H” drive may increase the dif- ferential oil temperature, resulting in possi-
ble damage to the driving system.
Further, the drive train will be subjected to
excessive loading possibly leading to oil leakage, component seizure, or other serious faults.NOTEl Do not tow a vehicle heavier than your own
vehicle.Operation under adverse
driving conditions E00801703899
If your vehicle becomes stuck
in sand, mud or snow
If the vehicle becomes stuck in snow, sand,
or mud, it can often be moved with a rocking
motion. Move the selector lever alternately
between the Sports mode and “R” (RE-
VERSE) position (with M/T, between 1 st
and
Reverse), while applying slight pressure to the accelerator pedal.
Operation under adverse driving conditions
8-19OVWE16E1For emergencies8

Avoid racing the engine or spinning thewheels. Prolonged efforts to free a stuck ve-
hicle may result in overheating, transmission and drivetrain failure. Allow the engine toidle for a few minutes to let the transmissioncool between rocking attempts.
If the vehicle remains stuck after several rocking attempts, seek other assistance.WARNINGl When attempting to rock your vehicle out
of a stuck position, be sure that the area around the vehicle is clear of people and
physical objects. The rocking motion may cause the vehicle to suddenly launch for-ward or backward, causing injury or
damage to nearby people or objects.
On a flooded road
l Avoid flooded roads. Water could enter
the brake discs, resulting in temporarily
ineffective brakes. In such cases, lightly
depress the brake pedal to see if the brakes operate properly. If they do not,
lightly depress the pedal several times while driving in order to dry the brake
pads.
l When driving in rain or on a road with
many puddles a layer of water may form between the tyres and the road surface.
This reduces a tyre’s frictional resistance
on the road, resulting in loss of steering stability and braking capability.

To cope with this, observe the following
items: (a)Drive your vehicle at slow speed. (b)Do not drive on worn tyres. (c)Always maintain the specified
tyre inflation pressures.
On a snow-covered or frozen
road
l When driving on a snow-covered or fro-
zen road, it is recommended that you use snow tyres or tyre chains.
Refer to the “Snow tyres” and “Tyre
chains” sections.
CAUTION• Avoid sudden braking, sudden acceleration,
and sharp turning; such operations could cause skidding and spinouts. Also, doing so could cause damage to the drivetrain.l Depressing the brake pedal during travel
on snowy or icy roads may cause tyre slippage and skidding. When traction be-
tween the tyres and the road is reduced
the wheels may skid and the vehicle can-
not readily be brought to a stop by con- ventional braking techniques. Brakingwill differ, depending upon whether you have anti-lock brakes (ABS). As your
vehicle is equipped with ABS, brake by pressing the brake pedal hard, and keep-
ing it pressed.
l Allow extra distance between your vehi-
cle and the vehicle in front of you, and avoid sudden braking.
l Accumulation of ice on the braking sys-
tem can cause the wheels to lock. Pullaway from a standstill slowly after con-
firming safety around the vehicle.CAUTIONl Do not press the accelerator pedal rapidly. If
the wheels break free of the ice, the vehicle
could suddenly start moving and possibly
cause an accident.
On a bumpy or rutted road
Drive as slow as possible when driving on
bumpy or rutted roads.
Operation under adverse driving conditions
8-20OVWE16E1For emergencies8

Engine compartment fuse loca-tion table
E01008001913
Engine compartment fuse location (Type A)
No.SymbolElectrical systemCapaci- ty1Alternator140 A *12Fuse (+B)60 A*13Ignition
switch40 A *1*1
: Fusible link
*2 : Vehicles without discharge headlamps
*3 : Vehicles with discharge headlampsNo.SymbolElectrical
systemCapaci- ty4Electric win-dow control30 A *15Engine con-
trol20 A *16Fuel pump20 A7Rear heater25 A8Accessory
socket25 A9Fuel line heat- er25 A10Condenserfan motor25 A11Rear air con- ditioning20 A
12
Horn (Theft-
alarm system)
15 A
Wiper de-icer13Horn10 A14Automatic
transmission20 A*1 : Fusible link
*2 : Vehicles without discharge headlamps
*3 : Vehicles with discharge headlampsNo.SymbolElectrical
systemCapaci- ty15Hazard warn-ing flasher10 A16Stop lamps15 A17Radio10 A18Room lamp15 A19Air condition- ing10 A20Front foglamps15 A21———22Windscreen wiper20 A23Tail lamp(right)7.5 A24Tail lamp (left)7.5 A25Headlamp lowbeam (right)10 A *220 A*326Headlamp low
beam (left)10 A *2*1
: Fusible link
*2 : Vehicles without discharge headlamps
*3 : Vehicles with discharge headlamps
Fuses
10-22OVWE16E1Maintenance10

Vehicle labelingE01100102886
1. Vehicle identification num-
ber
The vehicle identification number is stamped on the bulkhead as shown in the illustration.
2. Vehicle information code
plate
The vehicle information code plate is clipped
as shown in the illustration.
The plate shows model code, engine model,
transmission model and body colour code, etc.
Please use this number when ordering re-
placement parts.
1- Model code
2- Engine model code
3- Transmission model code
4- Body colour code
5- Interior code
6- Option code
7- Exterior code
Vehicle identification number
plate (RHD vehicles only)
The vehicle identification number is stamped on the plate riveted to the left front corner of
the instrument panel pad. It is visible from outside of the vehicle through the wind-
screen.
Vehicle labeling
11-02OVWE16E1Specifications11

No.ItemQuantityLubricants
1Engine oil
3000 modelsOil pan4.3 litres
Refer to page 10-04.
Oil filter0.3 litre
3200 models
Oil pan7.5 litresOil filter1.0 litreOil cooler1.3 litres
3800 models
Oil pan4.3 litresOil filter0.3 litreOil cooler0.3 litre
2Automatic transmission flu-
id3000 models, 3800 models9.7 litresMITSUBISHI MOTORS GENUINE ATF SPIII3200 models *110.9 litresMITSUBISHI MOTORS GENUINE ATF-PA*1
: 3200 models do not have a dipstick.CAUTIONl For the automatic transmission fluid, use only the MITSUBISHI MOTORS GENUINE ATF.
Use of a different fluid could damage the transmission.No.ItemQuantityLubricants3Brake fluidAs requiredBrake fluid DOT3 or DOT44Clutch fluidAs required
5Washer fluid
Front5.1 litres
—Rear *11.4 litres*1
: Rear washer fluid container is located on the backdoor. (Refer to “Rear window washer fluid” on page 10-08.)
Refill capacities
11-15OVWE16E1Specifications11