2016 MITSUBISHI LANCER light

Keyless
entry
system
(if
so
equipped)
Features and controls
5-9
5
N0054360
1131
The
door
unlock
function
can
be set
to the
following two conditions. Each
time
the
door
unlock
function
is set,
a
chime
will
sound
to tell you
the conditi
on
of
the door unlock function.1.Remove the key from the ignition switch.2.Open
the
driver
’s door
and
turn
the
com-
bination
headlights
and
dimmer
switch
to
the “OFF” position.3.Press
the
LOCK
button
(1)
for
4 to 10
sec-
onds
and
press
the
UNLOCK
button
(2)
during this time.4.Release
in
sequence
the
LOCK
and
UNLO
CK
buttons
within
10
seconds
of
pressing the LOCK button in step 3.
N00543700
018
If you
are
near
your
vehicle
and
feel
threat-
ened,
you
may
activate
the
alarm
to call
atten-
tion as follows:
1.Press
the
PANIC
button
(4)
for
more
than
1 s
econd.
2.The
headlights
will
blink
on
and
off and
the
horn
will
sound
intermittently
for
about
3 minutes.
3.To turn
off the
alarm,
press
any
button
on
the remote control transmitte
r.
N00543800
019
Only
remote
control
transmitters
pro-
grammed
with
the
vehicle’
s electronics
can
lock or unlock all doors.If you
lose
the
remote
control
transmitter
, you
can
order
a remote
control
transmitter
from
your
authorized
Mitsubishi
Motors
dealer
by
referring
to the
key
number
.
To prevent
vehicle
theft,
the
ID
codes
for
all
the
remote
control
transmitters
except
the
one
for the lost key must be programmed again.Take
your
vehicle
and
all
the
remaining
remote
control
transmitters
to your
authorized
Mitsubishi
Motors
dealer
to
have
your
ID
codes
programmed
again.
N00543900
010
To add
a remote
control
transmitte
r, you
must
already
have
one
registered
remote
control
transmitte
r.
Registering
the
ID
code
can
be
done
by
your
-
self
or
by
your
authorized
Mitsubishi
Motors
deale
r. For
you
to
register
the
ID
code
your
-
self,
follow
the
“Customer
remote
control
transmitter programming” procedure below
.
If you
choose
to
have
your
authorized
Mit-
subishi
Motors
dealer
register
the
ID
code,
take
your
vehicle
and
all
remaining
keys
to
your authorized Mitsubishi Motors dealer
.
N0054400
1174
You
can
program
new
remote
control
trans-
mitters
to
the
system
if you
have
one
valid
(already
registered)
remote
control
transmit-
ter
by
doing
the
following:
Setting of door unlock function

Number
of
chimes
Condition
One chim
e
All doors unlock
Two chimes
Driver
’s door unlock only
Using the panic alarm

Replacement r
emote contr
ol
transmitters

Additional r
emote contr
ol
transmitters

NOTE
You
are
provided
with
two
remote
control
transmitters,
but
you
may
register
up
to eight
remote
control
trans
mitters
.
Customer r
emote contr
ol trans-
mitter pr
ogramming (Except
for vehicles sold in Canada)

Keyless
entry
system
(if
so
equipped)
5-10
Features and controls
5
1.Have
available
all (current
and
new)
remote
control
transmitters
you
wish
to
registe
r.
2.With
a valid
(already
registered)
remote
control
transmitte
r, press
the
UNLOCK
button
(2)
for
4 to 10
seconds.
Then
press
and hold the LOCK button (1).3.Within
10
seconds
of
pressing
the
LOCK
button,
release
the
LOCK
and
UNLOCK
buttons in sequence.At
this
time,
ID
codes
for
all
remote
con-
trol
transmitters
except
for
the
transmitter
used
in
steps
2 and
3 are
erased
and
the
answerback
function
(door
is locked
and
unlocked)
informs
you
that
the
registra-
tion mode has been activated.4.Within
60
seconds
after
step
3, complete
the
following
ID
code
registration
opera-
tion
using
the
next
remote
control
trans-
mitter
you
wish
to
register
within
4seconds.i.Press
both
the
LOCK
and
UNLOCK
buttons
for
2 seconds.
ii.Release
both
the
LOCK
and
UNLOCK
buttons
for
1 second.
iii.
Press the UNLOCK button.The
answerback
function
informs
you
that
the
ID
code
registration
of
the
transmitter is completed.
5.To register
the
ID
codes
of
additional
remote
control
transmitters,
repeat
step
4
within 60 seconds after step 4.
6.If no
ID
code
of
a remote
control
trans-
mitter
is
registered
within
60
seconds
after
step
4, the
registration
mode
is can-
celed
and
the
normal
mode
returns.
N00546
101111
Your
keyless
entry
system
operates
on
a radio
frequency
subject
to
Federal
Communica-
tions
Commission
(FCC)
Rules
(For
vehicles
sold
in
U.S.A.)
and
Industry
Canada
Rules
(For
vehicles
sold
in
Canada).
This
device
complies
with
Part
15
of
FCC
Rules
and
Industry
Canada
licence-exempt
RSS
stan-
dard(s).Operation
is subject
to the
following
two
con-
ditions
.
This
device
may
not
cause
harmful
inter
-
ference.
NOTE
For
verification
purpose
s, try
to lock and
unl
ock the doors
after the registration
is
completed
.
The
indicator
light
(5)
comes
on
each
time
a
button
is pressed.
The keyless
entry
system
doe
s not
work
if
the key is in the ignition switch
.
The
remo
te con
trol trans
mitter
can
be use
d
from
about
40 feet
(12 m) away. However
,
this
distan
ce
may
change
if your
vehicle
is
near
a TV
transmitting
tower
, a power
sta-
tion, or a radio station.If the UNL
OCK
button
(2)
is pre
ssed whe
n
all
doors
are
locked
and
no
doors
are
opened
within about
30
seconds,
the doors
will auto-
matically
re-lock.
If the
following
conditions
are
observed
after
pressing
the
buttons
on
the
remote
control
transmitter
, the battery
in the remo
te cont
rol
transmitter
may need
to be
replaced
.
•The doors
cannot
be locked or unl
ocked.
•The trunk
lid cannot
be ope
ned.
•The panic
alarm
cannot
be operated.
•The
indicator
light
(5)
is dim
or
does
not
come
on.
If you
lose
your
remote
control
transmitter
,
pleas
e contact
an authorized
Mitsubi
shi
Motors dealer for a replacement.If you
wish to obtain
an additional
remote
control
transmitter
, please
contact
an
autho-
rized
Mitsubishi Motors
dealer
. A max
imu
m
of
eight
remote
control
transmitters
can
be
programmed for your vehicle.To use
the
new
remote
control
transmitters,
it
is necessary
to register
the
key
with
both
the
electronic
immobilizer
and
keyless
entry
sys-
tem. Also refer to “Electr
onic
immobilizer
(Anti-
theft starting
system)
: Cust
omer
key pro-
gramming”
on
page
5-6.
General information

NOTE

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)5-14
Features and controls
5
N0050330
0025
The
operating
range
is
the
interior
of
the
vehicle.
N0050340
1241
While
carrying
the
F.A.S.T
.-key
, press
the
driver
’s or front
passenger
’s door
lock/unlock
switch
(A)
within
the
operating
range
to lock
all the doors. The
turn
signal
lights
will
blink
once
and
the
buzzer will sound once. Also
refer
to
“Door
locks”
and
“Power
door
locks” on pages 5-34 and 5-37 respectively
.
*:Front of the vehicle
:Operating range
NOTE
Only
the
F.A.S.T
.-key
that
is detectable
by
the
doors
and
the
trunk
lid
can
lock
and
unlock
the
doors
and
open
the
trunk
lid.
The system
may
not
ope
rate
if the F.A.S.T
.-
key is too
close
to the windshield,
door
win-
dows
or trunk
lid.
Even if the
F.A.S.T
.-key
is within
abou
t
2.3feet
(70
cm)
of the driver
’s or front pas-
senger
’s door lock/un
lock
switch
and
cen
ter
of the
trunk
lid,
the
system
may
not
operate
if the
key
is close
to the
ground
or in a high
position.If the
F.A.S.T
.-key
is within
the
operating
range,
even
a person
not
carrying
the
F.A.S.T
.-key
can
lock
and
unl
ock
the doors
or open
the
trunk
lid
by
pressing
the
driver
’s
or front
passenger
’s door lock/u
nlock
switch
or the trunk
lid
OPE
N switch.
Operating range for starting the engine
*:
Front of the vehicle
:Operating range
NOTE
Even
if the F.A.S.T
.-ke
y is within the
oper
at-
ing
range,
it may
not
be
possible
to start
the
engi
ne if the key is in a stora
ge space suc
h as
the glove
compartmen
t, on
top
of the instru-
ment
panel,
or
in the
door
pocket
or
trunk
compartment.Even
if the
F.A.S.T.-key
is outs
ide
the
vehi-
cle,
it may
be
possible
to start
the
engine
if
the key is too
close
to a door
or door
win-
dow
.
To operate using the F
.A.S.T
.-
key

To lock the doors

NOTE
In cas
es such
as the
follow
ing,
the
F.A.S.T.-
key does not operate.

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-15
5
While
carrying
the
F.A.S.T
.-key
within
the
operating
range,
you
can
unlock
the
doors
by
F.A.S.T
-key operation.
The
dome
light
will
turn
on
for
30
seconds.
The
turn
signal
lights
will
blink
twice
and
the
buzzer will sound twice. Also
refer
to
“Door
locks”
and
“Power
door
locks” on pages 5-34 and 5-37 respectively
.
Press
the
driver
’s door
lock/unlock
switch
(A) to unlock only the driver
’s door
.
Within
about
2 seconds,
press
the
driver
’s
door
lock/unlock
switch
(A)
one
more
time
to
unlock all the doors.
Press
the
front
passenger
’s door
lock/unlock
switch
(A)
to unlock
all
the
doors.
•There is a F.A.S.T
.-ke
y in the passenge
r
compartment•A door is
open or ajar
•The
ignition
switch
is in a position
other
than
“LO
CK”
•The emer
gency
key
is inserted
into
the
igni-
tion
switch
When the vehicle
is locked, the theft-alar
m
system
pre
pares to enter the ar
med
stag
e.
Refer to “Th
eft-alar
m system”
for
furt
her
details
on
page
5-41.
To unlock the doors

NOTE
NOTE
Settings
can
be
changed
so that
all
doors
are
unlocked
automatically
by
one
press
of
the
driver
’s doo
r lock
/un
lock switch (A).
Refer
to “Setting
of door
unlock
function”
on
pages
5-9
and
5-31.
NOTE
If the doo
rs are unl
ocked
whe
n all
doors
are
locked and no
doors
are ope
ned within about
30
seconds,
the
doors
will
automatically
re-
lock.In cases
such
as the
following,
the
F.A.S.T
.-
key doe
s not
ope
rate.
•A door i
s ope
n or ajar
•The ignition
switch
is in a position
other
than “LOCK”
•The emer
gency key is inse
rted
into the igni
-
tion
switch
The
amount
of time
after
unlocking
until
the
vehicle
re-locks
automatically
can
be
adjusted.
See
an
authorized
Mitsubishi
Motors dealer fo
r details
.
Function
settings
can
be modi
fied
as stated
below
.
See
an authorized
Mitsubishi Mot
ors
dealer
for
details.
•Activ
ating
the ope
ration
confi
rmation
func
-
tion
(blink
of
the turn
signal
light
s) onl
y
duri
ng
locking, or onl
y duri
ng unl
ocking.
•Deacti
vating
the ope
ration
confi
rmatio
n
function
(blink
of the
turn
signal
lights
) and
buzzer
.
•Modifying
the
number
of blink
in the
oper
-
ation
confirmation
function
(blink
of
the
turn
signal
lights).
•Making
the buzzer
sound
whe
n the
F.A.S.T
.-ke
y is remove
d from
the passenge
r
compartment
when
all
the
doors
are
clos
ed.

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped) 5-20
Features and controls
5
N005601
00105
Type 1
Type 2
When
the
ignition
switch
is
in
a position
other than “LO
CK
(PUSH
OFF)
”, all
the
doors
are
closed,
and
someone
tries
to
lock
the
vehicle
by
pressing
the
drive
r’s or front
passenger
’s
door
lock/unlock
switch,
the
warning
display
is displayed
and
the
buzzer
sounds
for
about
3 seconds
as a warning,
and
the doors cannot be locked.
N0051430
0025
Turn
the
ignition
switch
to the
“LOCK”
posi-
tion.Turn the steering wheel until it is locked.Turn
the ignition
switch
to
the “AC
C”
posi-
tion
while
moving
the
steering
wheel
slightl
y.
N0051460
1386
Do
not
operate
the
starter
motor
for
longer
than
15
seconds
as
this
could
run
the
bat-
tery
down
or
damage
the
starter
motor
. If
the
engine
does
not
start,
turn
the
ignition
switch
back
to the
“LOCK”
position,
wait
a few
seconds,
and
then
try
again.
Trying
repeatedly
with
the
engine
or starter
motor
still
turning
will
damage
the
starter
mechanism.
Ignition switch turn-off
reminder
system

Steering wheel lock

To loc
k
To unloc
k
CAUTIONCarry the key with you when leaving the
vehicle
.
If your veh
icle
need
s to be tow
ed, turn the
ignition switch to the “ACC”
position to
unlock the steer
ing wheel
.
NOTE
If the fron
t wheels are turned, the anti-theft
lock may
sometime
s mak
e it difficu
lt to turn
the ignition switch from “LOCK” to “ACC”
position
. Firmly
turn the steer
ing wheel
to
the left or to the right as you turn the ignitio
n
switch
.
Startin
g
Tips for starting

CAUTION

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-21
5
If the
engine
will
not
start
because
the
bat-
tery
is
weak
or
dischar
ged,
refer
to
“Jump-starting
the
engine”
on
page
8-2
for instructions.A longer
warm
up
peri
od
wil
l only
con-
sume
extra
fuel.
The
engine
is warmed
up
enough
for
driving
when
the
bar
graph
of
the
engine
coolant
temperature
display
starts
to move.
Refer
to “Interrupt
display
screen
(W
ith
ignition
switch
in the
“ON”
position)” on page 5-101.
Your
vehicle
is equipped
with
an
electroni-
cally
controlled
fuel
injection
system.
This
is
a
system
that
automatically
controls
fuel
injection.
There
is
no
need
to
depress
the
accelerator pedal when starting the engine.The starte
r mo
tor sho
uld
not
be run
for
mo
re
than
15
seconds
at a time.
To prevent
battery
drain,
wait
a few
seconds
between attempts to restart the engine.1.Make
sure
all
occupants
are
properly
seated with seat belts fastened.2.Make sure the parking brake is applied.3.Press
and
hold
the
brake
pedal
down
firmly with your right foot.4.Press
and
hold
the
clutch
pedal
all
the
way
down
(manual
transaxle).
5.On
vehicles
with
manual
transaxle,
place
the
gearshift
lever
in
the
“N”
(Neutral)
position.On
vehicles
with
continuously
variable
transmission
(CVT)
make
sure
the
selec-
tor lever is in the “P” (P
ARK) position.
6.While
pushing
the
ignition
switch
from
“LOCK”
(PUSH
OFF)
to “LOCK”
(PUSH
ON),
set
the
ignition
switch
to the
“ON”
position
and
confirm
that
all
warn-
ing
lights
and
warning
displays
are
oper
-
ating properly
.
7.Without
pressing
the
accelerator
pedal,
slowly
turn
the
ignition
switch
to
the
“ST
ART”
position
to
start
the
engine.
Release
the
ignition
switch
when
the
engine
starts.
After
several
attempts,
you
may
experience
that the engine still does not start.
W
AR
NING
Never
run
the
engi
ne in a clos
ed or poorly
ventilate
d area
any
longer
than
is need
ed
to move your
veh
icle
out
of the
area. Car
-
bon
monoxide
gas,
which
is odorless
and
extr
emely
poisonous,
could
build
up
and
cause serious injury or death.CAUTIONDo not
push-star
t the vehicle.
Do
not
run
the
engine
at high
rpms
or drive
at high speeds
until
the
engin
e has had a
chance
to warm
up.
Releas
e the ignition
switch
as soon
as the
engi
ne starts. Otherwi
se, the starter motor
will be damag
ed.
Starting
the
engine

NOTE
For
models
equipped
with
a manual
trans-
axle,
the
starter
will
not
operate
unless
the
clutch
pedal
is fully
depressed
(Clutch
inter
-
lock). This is a safety feature.
NOTE
On
vehicles
with
CVT
, the
starter
will
not
ope
rate
unless
the selector
lev
er is in the “P”
(PARK)
or “
N” (NE
UTRAL
) position.
For s
afety
reasons, s
tart the engi
ne in the “P”
(PARK)
position
so
that
the wheels
are
locked.NOTE
Minor
noi
ses may
be heard
on
engi
ne start-
up.
These will disappear
as the engi
ne warms
up.
When the engine is hard to start

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)5-22
Features and controls
5
1.Make
sure
that
all electric
devices,
such
as
lights,
air
conditioning
blower
and
rear
window defogger
, are turned o
ff.
2.While
depressing
the
brake
pedal
on
vehi-
cles
equipped
with
continuously
variable
transmission
(CVT)
or the
clutch
pedal
on
the
vehicles
equipped
with
manual
trans-
axle,
press
the
accelerator
pedal
halfway
and
hold
it there,
then
crank
the
engine.
Release
the
accelerator
pedal,
immedi-
ately after the engine starts.3.If the
engine
still
will
not
start,
the
engine
could
be
flooded
with
too
much
gasoline.
While
depressing
the
brake
pedal
on
vehi-
cles
equipped
with
CVT
or
the
clutch
pedal
on
the
vehicles
equi
pped
with
man-
ual
transaxle,
push
the
accelerator
pedal
all
the
way
down
and
hold
it there,
then
crank
the
engine
for
5
to
6
seconds.
Return
the
ignition
switch
to the
“LOCK”
position
and
release
the
accelerator
pedal.
Wait
a few
seconds,
and
then
crank
the
engine
again
for
5 to
6 seconds
while
depressing
the
brake
pedal
or
the
clutch
pedal,
but
do
not
push
the
accelerator
pedal.
Release
the
ignition
key
if
the
engine
starts.
If the
engine
fails
to
start,
repeat
these
procedures.
If the
engine
still
will
not
start,
contact
your
local
Mitsubi-
shi
Motors
dealer
or
a repair
facility
of
your choice for assistance.
When
the
ambient
temperature
is
-4°F
(-20°C)
or
lower
, it may
not
be
possible
to
start
from
a standstill
even
with
the
selector
lever
in
the
“D”
(DRIVE)
or
“R”
(REVERSE) position.This
phenomenon
occurs
because
the
trans-
axle
has
not
warmed
up
suf
ficiently;
it does
not
indicate
a problem.
If this
occurs,
place
the
selector
lever
in the
“P”
(PARK)
position
and let the engine idle for at least 10 minutes.The
transaxle
will
warm
up,
and
you
will
be
able to drive normally
.
Do
not
leave
the
vehicle
during
warm-up
operation.
N0051480
0020
N0051520
0148
The
emer
gency
key
is built
into
the
F.A.S.T
.-
key
.
When
the
F.A.S.T
.-key
cannot
be
used,
such
as when
the
battery
of the
F.A.S.T
.-key
or the
vehicle
has
run
down,
the
emer
gency
key
can
be
used
to
lock
and
unlock
the
driver
’s door
and to start the engine. To use
the
eme
rgency
key
(1),
unlock
the
lock
knob
(2)
and
remove
it from
the
F.A.S.T
.-key
(3). Turn
the
emer
gency
key
toward
the
front
of
the
vehicle
to
lock
the
door
. After
checking
that
the
door
is locked,
turn
the
emer
gency
key back to the center and remove it.
Startability
of
continuously
variable
transmission
(CVT)
vehicles
at extr
emely
cold ambient temperatur
e
To operate
using
the
emergency
key

Emergency
key

NOTE
Onl
y use
the emer
gency key in an emer
-
gency
. When
the
battery
of the
F.A.S.T
.-key
has
run
dow
n, replace
the
battery
as soon
as
possible
and
use
it as a F.A.S.T
.-key
again.
After
using
the emer
gency key, be sure
to
reinse
rt it into the F.A.S.T
.-ke
y.
To lock
or
unlock
the
driver
’s door
with
the emergency key

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-25
5
Turn
the
eme
rgency
key
to the
“LO
CK
” pos
i-
tion.Turn the steering wheel until it is locked.Turn
the
emer
gency
key
to
the
“ACC”
posi-
tion
while
moving
the
steering
wheel
slightly
.
Tips for starting
Do not
operate
the
starter
motor
continu-
ously
for
longer
than
15
seconds
as
this
could
run
the
battery
down
or damage
the
starter
motor
. If the
engine
does
not
start,
turn
the
eme
rgency
key
back
to
the
“LO
CK
” pos
ition,
wait a few
seconds
,
and
then
try
again.
Trying
repeatedly
with
the
engine
or
starter
motor
still
turning
will damage the starter mechanism.If the
engine
will
not
start
because
the
bat-
tery
is
weak
or
dischar
ged,
refer
to
“Jump-starting
the
engine”
on
page
8-2
for instructions.A longer
warm
up
period
will
only
con-
sume
extra
fuel.
The
engine
is warmed
up
enough
for
driving
when
the
bar
graph
of
the
engine
coolant
temperature
display
starts
to move.
Refer
to “Interrupt
display
screen
(W
ith
ignition
switch
in the
“ON”
position)” on page 5-101.
Starting the engineYour
vehicle
is equipped
with
an
electroni-
cally
controlled
fuel
injection
system.
This
is
a system
that
automatically
controls
the
fuel
injection.
There
is
no
need
to
depress
the
accelerator pedal when starting the engine.The starter
mo
tor sho
uld
not
be run
for
mo
re
than
15
seconds
at a time.
To prevent
battery
drain,
wait
a few
seconds
between attempts to restart the engine.1.Make
sure
all
occupants
are
properly
seated with seat belts fastened.2.Make sure the parking brake is applied.3.While
pushing
the
lock
release
buttons
(A),
remove
the
cover
of
the
ignition
switch.
To lock
To u
nlock
CAUTIONRemove
the emer
gency key whe
n leav
ing
the
vehicle.
If your
vehicle
needs
to be
towed,
turn
the
emer
gency
key to the
“ACC”
position
to
unlock the steering wheel.NOTE
If the
front
wheels
are
turned,
the
anti-theft
lock
may
sometimes
make
it difficult
to turn
the
emer
gency
key
from
“LO
CK” to “ACC”.
Firmly
turn
the steer
ing
wheel
to the left or
to the right
as you t
urn
the emer
gency ke
y.
Starting
W
AR
NING
Never
run
the engin
e in a clos
ed or poorly
ven
tilated
area
any lon
ger
than is need
ed
to move
you
r veh
icle
out of the area.
Car-
bon
monoxi
de gas,
which
is odorless
and
extr
emely
poi
sonous,
coul
d build
up
and
cause
serious
injur
y or
death.
CAUTIONDo not push-star
t the vehicle.
Do
not run
the engin
e at high
rpms
or drive
at high
speeds
until
the
engine
has
had
a
chance to
warm up.
Releas
e the
emer
gency
key
as soon
as the
engine
starts
. It
will
damage
the
starter
motor.
CAUTION