2016 MITSUBISHI LANCER seats

Supplemental Restraint System (SRS) - airbag
Seat and restraint systems
4-25
4
N00418100
277
The
passenger
’s
airbag
off
indicator
is
located in the instrument panel.
The
indicator
normally
comes
on
when
the
ignition
switch
is turned
to the
“ON”
position
and goes out a few seconds later
.
In
the
following
situations,
the
indicator
will
stay
on
to show
that
the
passenger
’s front
air-
bag is not operational.The
passenger
’s seat
weight
sensors
sense
a weight
of
less
than
approximately
66
pounds
(30
kg)
on
the
front
passenger
seat.The
front
passenger
’s seat
is not
occupied.
When
the
weight
applied
to the
front
passen-
ger
seat
is
sensed
to
be
approximately
66
pounds
(30
kg)
or
greater
, the
indicator
goes
out
to show
that
the
passenger
’s front
airbag
is operational.
W
AR
NING
If any
of
the
followi
ng
condi
tions
occu
r,
you
shoul
d imme
diately
have
your
vehicle
inspected
by an authorized
Mitsubi
shi
Motors
dealer
as soon
as possible:
•The SRS
warn
ing does
not
initially come
on
whe
n the
ign
ition
swi
tch is tur
ned to
the
“ON” or “ST
ART” posi
tion.
•The
SRS
warning
does
not
go
out
after
several
seconds.
•The SRS
warn
ing comes
on while
you
are
driv
ing.
To ensur
e that
the
passe
nge
r’s seat weight
sensors
can
corr
ectly
sense
the
weight
being
applied
to the
seat
, observe
the
fol-
lowing
ins
tructions.
Failur
e to follow
these
instr
uctions
can
advers
ely
affect
the
per-
for
mance
of
the
passe
nge
r’s airbag
sys-
tem.•Adjust
the
seat
to
the
correct posi
tion,
and
sit well
back
against
the seatb
ack
.
Refer
to “Fr
ont seats
” on page
4-3.
•Do
not
reclin
e the
seatbac
k mor
e than
necessary
.
•Never
have
mor
e than
one
person
(adult
or child)
sitting
on
the
seat.
•Do
not
place
anything
between
the
seat
and the floor console.•Do
not
hang
anything
on
the
front
pas-
sen
ger
’s seatback.
•Do not remove
the
head
restraints.
•When
attaching
a child
restraint
system,
secur
e it firmly
.
•Do not place
luggage
or
oth
er objects
on
the
seat.
•Do
not
use
a seat
cover
or a cushion.
•Do
not
modify
or
replace
the
seat
and
seat
belt.
•Do
not
place
luggage
or other
object
s
under
the
seat.
•Do not
place
the floo
r mat
on the
seat
rails
.
•Do
not
expose
the
sensors
to
liquids
or
vapors.•Do not subject
the sensors
to shock
.
•Do not allow
rear
-seat
occupa
nts to push
the
front
passenger
seat
with
their
feet
or
force the
front passe
nger s
eat upward
.
•Do not
allow
rear
-seat
occupants
to grasp
the
front
passe
nge
r’s seatbac
k or put
their
arms
around i
t.
•When attac
hing
a child restraint
syste
m
in
the
rear
seat, make
sure it does
not
interfer
e with
the front seat.
If
the
vehicle
is
involved
in
a sever
e
impac
t, have
the
SRS
sensor
s inspect
ed by
an authorized
Mitsubi
shi
Motor
s dealer
as
soon
as possi
ble.
Passenger
’s airbag
off
indicator
W
AR
NING

Supplemental Restraint System (SRS) - airbag4-32
Seat and restraint systems
4
N0041920
1230
The
curtain
airbags
are
contained
in the
front
and
rear
pillars
and
roof
side
rail.
The
curtain
airbag
is designed
to inflate
only
on
the
side
of
the
vehicle
that
is impacted,
even
with
no
passenger in the front seat.Curtain airbag system
(if so
equipped)
W
AR
NING
The side airb
ag
and
curtain airbag
can
cause
serious
injur
y or death
to
any
one
too close
to the
airbag
whe
n it deploys.
To
reduce
the
risk
of injur
y from a deployin
g
side airb
ag and
curtain
airb
ags,
all
occu
-
pants
must
be properly
restrained and
seated
well
back,
upright,
and
in the
mid-
dle of
the
seat.
Do
not
lean
agai
nst
the
door
.
W
AR
NING
In
ord
er to reduce
the
risk
of injury
from
a deploying
side
airbag,
do
not
allow
any
rear seat passe
ngers
to hol
d onto
the
bac
k
of either
front
seat.
Specia
l care shoul
d be
take
n with children.
Do not place
any
objects
near or around
the
front
of
either
front
seatback.
Such
objects
can
interf
ere with proper
side air-
bag deployment
and
cause
injury
durin
g
deployme
nt of the
side airb
ag.
Do
not
place stick
ers,
labels
or addi
tional
trim
on
the
bac
k of either
front
seat.
The
y
can
interf
ere with
proper
side airbag
deploymen
t.
Do
not
install
seat
covers
or re-cover
seats
that
have
side
airbags.
Covers
can
inter
-
fere with proper
side airb
ag
deploymen
t
and
adversely
affect
side
airbag
perfor
-
mance.
Do
not
attach
a micr
ophone
(A)
or
any
other
object
around
the
part
wher
e the
curtain
airbag
(B)
deploys,
such
as on
the
windshield,
side
door
glass
or
front
and
rear
pillars
and
roof
side
rail.
When
the
curtain
airbag
inflate,
the
micr
ophone
or
other
object
may
be
hurled
with
great
for
ce or the
curtain
airbag
may
not
inflate
corr
ectly
, resulting
in
death
or
serious
injury.
W
AR
NING

Supplemental Restraint System (SRS) - airbag
Seat and restraint systems
4-35
4
N00408500
672
Head-on
collision
Rear e
nd c
ollisi
on
SRS
servicing W
AR
NING
Any
mai
nte
nance
perfor
med on or
near
the
compone
nts
of the
SRS
shoul
d be per-
form
ed only by
an
authorized
Mitsubi
shi
Motor
s dealer
. Do
not
perm
it any
one
else
to do any
serv
ice,
inspect
ion,
mai
nte
nanc
e
or
repair
on any
SRS
compone
nts
or wir-
ing.
Similarly, no par
t of the
SRS
shoul
d
ever
be
handled,
removed
or
disposed
by
anyone
except
an
authorized
Mitsubishi
Motor
s dealer
.
Impr
oper work
methods
on the
SRS
com
-
ponents
or
wiring
could
result
in an
acci-
dental
airb
ag deployme
nt
or coul
d make
the
SRS
inoperable.
Either
of these
situa-
tions
could
result
in
serious
injury
or
death. Do not modify your
steering
wheel
or
any
other
SRS
component
or
related
vehicle
part.
For
example,
replacement
of
the
steering
wheel,
or
modifications
to
the
front
bumper
or body
structur
e can
advers
ely
affect
SRS
perfor
mance
and
may
lead
to injury
.
If your
vehicle
has
receiv
ed any
damage
,
you
shoul
d have
the
SRS
inspect
ed by
an
authorized
Mitsubishi
Motors
dealer
to
make sur
e it is in pr
oper working order
.
Do
not
modi
fy your
front
seats,
center
pil-
lar or center
console.
Suc
h modi
ficati
ons
can
advers
ely
affect
SRS
performan
ce and
may
lead
to injury.
Also,
if you
discover
any
tear or ope
n
seam
in the seat
fab
ric
near
the side air-
bag,
have
the seat
inspected
by an autho-
rized
Mitsubi
shi
Motors
dealer
.
If you find
a cra
ck in or damage
to the
front
pillar
, rear
pillar
, or
roof
side
rail
wher
e the
curtain
airbag
is located,
have
the
SRS
inspected
by
an
authorized
Mit-
subishi
Motors
dealer
.
NOTE
When
you
trans
fer
owners
hip
of the
vehicle
to another
person,
we
urge
you
to alert
the
new
owner
that
it is equipped
with
the
SRS
and
refer
that
owner
to the
applicable
sec-
tions i
n this owne
r’s manual.

If you
decide
to junk
or scrap
your
vehicle,
we urge
you
to firs
t take
it to an
authorized
Mitsubi
shi Mot
ors
dealer
so that the SRS
can
be made s
afe
for
dispos
al.
If any
of
the
following
parts
needs
to
be
mod
ified
for
use by
a handicap
ped
person,
the adv
anced
airbag
system
will
be greatly
affected.
Pleas
e consult
an authorized
Mit-
subishi
Motors
dealer
for
assistance.
•Driver
’s seat
•Front
passenger
seat
•Front seat
belt
W
AR
NING

Bottle holder 5-172 Features and controls
5
N00502800049
There are bottle holders located on both sides of the front seats.
N00559000029
These grips are to support the body by hand while seated in the vehicle.
N00553600108
There is a coat hook on
the rear seat assist
grip of the driver’s side.
Bottle holder
CAUTION Do not drink beverages while driving your vehicle. This is distracting and could cause an accident. Vibration and shaking while driving may cause beverages to spill. Be very careful, as spilling hot beverages could cause burns.NOTE
 Make sure all lids are tightly closed when storing beverages that are in plastic bottles, etc.  Some beverages may not be stored, depend- ing on the size and shape of the plastic bot-tles, etc.
Assist grip
CAUTION Do not use the assist grips when getting into or out of the vehicle. The assist grips could detach and cause an accident.
Coat hook
(if so equipped)
BK0230300US.book
172 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Vehicle preparation before driving
Driving safety 6-3
6
N00629001741
For a safer and more enjoyable trip, always observe the following:  Before starting the vehicle, make certain that you and all passengers are seated and wearing their seat belts properly (with children in the rear seat, in appropriaterestraints), and that all the doors are locked.
 Move the driver’s seat as far backward as possible, while still keeping good visibil- ity, and good control of the steering wheel, brakes, accelerator, and controls.Check the instrument panel indicators and multi-information display for any possible problem.  Move the front passenger seat as far back as possible.  Make sure that infants and small children are properly restrained in accordance withall laws and regulations.
Check these by selecting the defroster mode, and set the blower switch on high. You should be able to feel the air blowing against the windshield. (Refer to “Defrosting or defogging the wind- shield and door windows” on page 7-7, 7-12, 7-17.) Check all the tires for heavy tread wear or uneven wear patterns. Look for stones, nails,glass, or other objects stuck in the tread. Look for any tread cuts or sidewall cracks. Check the wheel nuts for tightness, and the tires(including spare tire) for proper pressures.
WA R N I N G If a floor mat is the wrong size or is not properly installed, it can interfere with the operation of the pedals. Interference with the pedals can cause unintended accelera- tion and/or increased stopping distancesresulting in a crash and injury. Always make sure the floor mat does not interfere with the accelerator or brake pedal. Always use the retaining clip on the driver’s floorboard to secure the floormat. Always install the mat with the correct side facing down. Never install a second mat over or under an existing floor mat. Do not use a floor mat designed for another model vehicle ev
en if it is a Mit-
subishi genuine floor mat. Before driving, be sure to check the fol- lowing:• Periodically check that the floor mat isproperly secured with the retaining clips. If you remove the floor mat while clean-ing the inside of your vehicle or for any other reason, always check the condition of the floor mat after it has been rein-stalled.• While the vehicle is stopped with the engine off, check that the floor mat is not interfering with the pedals by depressingthe pedals fully.
Vehicle preparation before driving Seat belts and seats
Defrosters Tires
BK0230300US.bo
ok 3 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Loading information 6-6 Driving safety
6
Your front bumper can be damaged if you scrape it over curbs or parking stop blocks.Be careful when traveling up or down steep slopes where your bumper can scrape the road. When leaving the vehicle unattended, always carry the key and lock all doors.Always try to park your vehicle in a well lit area.
N00629900349
It is very important to know how much weight your vehicle can carry. This weight iscalled the vehicle capacity weight and includes the weight of all occupants, cargo and non-factory-installed options. The tireand loading information placard located on the driver’s door sill of your vehicle will show how much weight it may properly carry. It is important to familiarize yourself with the following terms before loading your vehicle:  Vehicle maximum load on the tire: load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight anddividing by two.  Vehicle normal load on the tire: load on an individual tire that is determined by dis-tributing to each axle its share of the curb weight, accessory weight, and normal occupant weight and dividing by two.
 Maximum loaded vehicle weight: the sum of - (a) Curb weight; (b) Accessory weight;(c) Vehicle capacity weight; and (d) Production options weight.  Curb weight: the weight of a motor vehi- cle with standard equipment including the maximum capacity of fuel, oil, and cool- ant. Accessory weight: the combined weight (in excess of those standard items which may be replaced) of automatic transmis- sion, power steering, power brakes, powerwindows, power seats, radio, and heater, to the extent that these items are available as factory- installed equipment (whetherinstalled or not).  Vehicle capacity weight: the rated cargo and luggage load plus 150 lbs (68 kg)
*
times the vehicle’s designated seating capacity.  Production options weight: the combined weight of those installed regular produc- tion options weighing over 5 lbs (2.3 kg) in excess of those standard items whichthey replace, not previously considered in curb weight or accessory weight, includ- ing heavy duty brakes, ride levelers, roofrack, heavy duty battery, and special trim.
WA R N I N G Leaving the engine running risks injury or death from accidentally moving the gear- shift lever (manual transaxle or the selec- tor lever (CVT) or from the accumulation of toxic exhaust fumes in the passengercompartment.
Where you park
WA R N I N G Do not park your vehicle in areas where combustible materials such as dry grass or leaves can come in contact with a hotexhaust, since a fire could occur.
When leaving the vehicle
Loading information
WA R N I N G Never overload your vehicle. Overloading can damage your vehicle, adversely affectvehicle performance, including handling and braking, cause tire failure, and result in an accident.
BK0230300US.bo
ok 6 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Fuses
Vehicle care and maintenance 9-27
9
* - Fusible link  Some fuses may not be installed on your vehicle, depending on the vehicle model or specifications.  The table above shows the main equip- ment corresponding to each fuse. 20
Power window con-
trol
30 A
*
21 Defogger 30 A
*
22
Heated
outside rearview
mirrors
7.5 A
23 115V Power outlet 15 A 24 Power seats
25 (20) A
25 Heated seats 30 ANo.
Sym- bol
Electrical system
Capac-ity
Engine compartment fuse location table * - Front of the vehicle
No.
Sym- bol
Electrical system
Capac-ity
1 Front fog lights 15 A 2 Engine 7.5 AEngine compartment fuse location
*
Behind the fuse block cover
*
3 Automatic transaxle 20 A 4 Horn 10 A 5 Alternator 7.5 A 6 Headlight washer 20 A 7 Air conditioning 10 A 8
/ ETV/Oil cooler fan
(Twin Clutch SST)
15 A
9 Security horn 20 A 10 Wiper deicer 15 A 11 — — — 13
Daytime running
lights
10 A
14
Headlight
(high beam) (left)
10 A
15
Headlight
(high beam) (right)
10 A
16
Head- light (low/high beam) (left)
Dis- charge
20 A
No.
Sym- bol
Electrical system
Capac-ity
BK0230300US.bo
ok 27 ページ ２０１５年７月３０日　木曜日　午後８時３８分

Cleaning the inside of your vehicle 9-42 Vehicle care and maintenance
9
N00945300171
1. Lightly wipe these off with a soft cloth soaked in a 3 % solution of gentle soapand water. 2. Dip cloth in fresh water and wring out well. Using this cloth, wipe off the deter-gent thoroughly.
N00945500131
1. To maintain the value of your new vehi-cle, maintain the upholstery carefully and keep the interior clean. Use a vacuum cleaner and brush to cleanthe seats. If stained, vinyl and synthetic leather should be cleaned with an appro- priate cleaner. Cloth fabrics can becleaned with either upholstery cleaner or a 3 % solution of gentle soap in lukewarm water. 2. Clean the carpeting with a vacuum cleaner and remove any stains with carpet cleaner. Oil and grease can be removed bylightly dabbing with a clean white cloth and spot remover.
N00945600161
1. To clean, lightly wipe the leather with a soft cloth soaked in a 5 % solution of gen-tle soap and water. 2. To rinse, dip the cloth in fresh water, wring it out well, and wipe off all thesoap. 3. To preserve and protect, use a leather pro- tecting agent on the genuine leather sur-face.
CAUTION Do not use organic substances (solvents, benzine, kerosene, alcohol, gasoline, etc.) or alkaline or acidic solutions. These chemicals can cause discoloring, staining or cracking of the surface.If you use cleaners or polishing agents, make sure their ingredients do not include the sub- stances mentioned above.NOTE
 Always read the instructions on the cleaner label.
Plastic, vinyl leather, fabric and flocked parts
NOTE
 Do not use cleaners, conditioners, and pro- tectants containing silicones or wax. Such products, when applied to the instru- ment panels or other parts, may cause reflec- tions on the windshield and obscure vision.Also, if such products get on the switches of the electrical accessories,
it may lead to fail-
ure of these accessories.
Upholstery
NOTE
 If fuzzing is difficult to remove from the seat upholstery, draw a suitable defuzzing brush over the surface in one direction.
Genuine leather
(if so equipped)
NOTE
 If genuine leather is wet with water, wipe it with a dry, soft cloth. If left damp, mildew may grow.  The genuine leather surface can be damaged if brushed with a nylon or synthetic fiber brush.  Organic solvents such as benzine, kerosene, alcohol, gasoline, acid or alkaline solvents can discolor the genuine leather surface and should not be used.  Genuine leather seats can mildew if not kept clean. Clean up any oil stains immediately.
BK0230300US.bo
ok 42 ページ ２０１５年７月３０日　木曜日　午後８時３８分