2016 MERCEDES-BENZ S-Class SEDAN turn signal

When you activate the EASY-ENTRY/EXIT fea-
ture, the crash-responsive EASY-EXIT feature
is also activated.
You can find further information on the crash-
responsive EASY-EXIT feature in the vehicle
Operator's Manual.
Activating/deactivating the panel
heating
The panel heating function warms the surfa-
ces with which the vehicle occupants fre-
quently come into contact. Activation of the
panel heating using COMAND as described
below only works if seat heating is activated
(see the vehicle Operator's Manual).
XCall up Vehicle Settings(Ypage 62).
XTo select Panel Heating: turn and press
the controller.
XTo change the setting: turn the controller.
Activating/deactivating the acoustic
locking confirmation
You can also set an audible signal to confirm
that the vehicle has been locked.
XCall up Vehicle Settings(Ypage 62).
XTo select Acoustic Lock Feedback: turn
and press the controller.
The function switches on or off, depending
on the previous setting.
You can find further information on the lock-
ing feature in the vehicle Operator's Manual.
Activating/deactivating the seat-belt
adjustment function
The seat-belt adjustment function adjusts the
driver's and front-passenger seat belt to the
upper body of the occupants.
XCall up Vehicle Settings(Ypage 62).
XTo select Belt Adjustment: turn and
press the controller.
The function switches on or off, depending
on the previous setting.
You can find further information in the vehicle
Operator's Manual.
64Vehicle settings
Vehicle functions

When the interior motion sensor is armed, a
visual and audible alarm is triggered if move-
ment is detected in the vehicle interior. This
can occur if someone reaches into the vehicleinterior without authorization, for example.
XCall up Vehicle Settings(Ypage 62).
XTo select Interior Motion Sensor: turn
and press the controller.
The function switches on or off, depending
on the previous setting.
Activating/deactivating the trunk lid
opening height restriction
Activating the Trunk Opening-height
Restrictionfunction allows you to avoid
bumping the trunk lid on a low garage ceiling,
for example.
XCall up Vehicle Settings(Ypage 62).
XTo select Trunk Opening-height
Restriction: turn and press the control-
ler.
The function switches on or off, depending
on the previous setting.
Voice amplification
Overview
The voice amplification function facilitates
communication between the driver and front
passenger with passengers in the rear com-
partment. The signals picked up by the micro-
phone in the rear view mirror are amplified
and played back over the speakers in the rear compartment, depending upon vehicle noise
levels.
An automatic adjustment matching occurs
based on speaker volume and ambient noise.
The optimum distance of the speaker from
the rear view mirror is approximately 50 cm.
When the system is active, the feeling of
space and the natural nature of speech play-
back should be maintained as far as is possi-
ble; speech intelligibility should be improved
when there is an increase in background
noise.
If the volume of a background media source
exceeds a threshold, the speech amplifica-
tion is stopped. The threshold is designed for
relaxed conversation with background music.
If the threshold value is not exceeded, the
voice amplification is continued with a slight
time delay.
Voice amplification is paused during active
telephone calls or when using the Voice Con-
trol System. A message will appear in the dis-
play.
You can assign these functions to the favor-
ites button (
Ypage 56).
Prerequisites
RYour vehicle is equipped with the
Burmester®surround sound system or the
Burmester®high-end 3D surround sound
system.
RThe ignition is switched on.
RDoors, side windows and the panorama
roof with power tilt/sliding panel are
closed.
iIf these conditions are not met, a corre-
sponding message will appear in the dis-
play.
Closing the side windows (see the vehicle
Operator's Manual).
Closing the panorama roof with power tilt/
sliding panel (see the vehicle Operator's Man-
ual).
Vehicle settings67
Vehicle functions
Z

memory card is formatted using the FAT file
system (e.g. FAT32).
All personal POIs of the selected category are
displayed on the map with a corresponding
symbol.
If the "Alert when approaching" (
Ypage 102)
function is activated, the symbols are dis-
played up to a map scale of 2 km.
XTo switch to navigation mode: press the
ß button.
XTo show the menu: slide6the control-
ler.
XTo select Options: turn and press the con-
troller.
XSelect Personal POIs.
XSelectDisplay on the Map.
The menu displays the categories available
on the SD memory card.
XTo select a category: turn the controller and
press to confirm.
All personal POIs in the selected category
are displayed Oor not displayed ª,
depending on the previous status.
Alert when approaching
Requirements: an SD memory card with per-
sonal POIs is inserted (
Ypage 217). The SD
memory card is formatted using the FAT file
system (e.g. FAT32).
If the vehicle is approaching a personal POI,
this is highlighted on the map and/or an audi- ble signal sounds.
For this purpose both the corresponding func-
tion "Alert when approaching" and the cate- gory containing the personal POI must be
activated.
XTo switch to navigation mode:
press the
ß button.
XTo show the menu: slide6the control-
ler.
XTo select Options: turn and press the con-
troller.
XSelect Personal POIs.
XSelectAlert When Approaching.
The menu displays the categories available
on the SD memory card.
XSelect AudibleorOptical.
The function is switched on Oor off ª,
depending on the previous status.
XTo select a category: turn the controller and
press to confirm.
The function is switched on Oor off ª, for
all personal POIs of this category, depend-
ing on the previous setting.
Saving personal POIs and routes
General notes
Personal POIs and routes are geodata which
are saved in the open GPX (GPS Exchange)
format on the SD memory card.
Requirement: the SD memory card is format-
ted using the FAT file system (e.g. FAT32).
Personal POI from current vehicle posi-
tion or crosshair position
XInsert the SD memory card (Ypage 217).
XTo switch to navigation mode: press the
ß button.
XWhen the map is displayed, press the con-
troller until a message appears.
The current vehicle position is saved to the
Not
Classifiedcategory on the SD mem-
ory card and also stored in the "Last desti-
nations" memory.
If the "Move map" function is selected
(
Ypage 83), the crosshair position is saved.
102Personal POIs and routes
Navigation

XPress the controller.
The compass display provides the followinginformation:
RThe current direction of travel with bear-
ing (360 degree format) and compass
direction
RLongitude and latitude coordinates in
degrees, minutes and seconds
RHeight (rounded off) above sea level
RNumber of GPS satellites from which
a signal can be received
XTo exit the compass display: press the
% button.
Drive information
XCall up the navigation menu (Ypage 133).
XTurn the controller until Drive Informa‐
tionis brought to the front.
XPress the controller.
TheStarting Drive Information.
Please Wait...message appears.
You will then see maps with the current
vehicle position and the vicinity of the des-
tination in different scales, these are auto-
matically displayed one after another.
USA: if mbrace is activated for Internet
access, additional information can be dis-
played, e.g. weather at the destination
(
Ypage 176).
Canada: if a mobile phone is connected to
COMAND via Bluetooth
®(Ypage 140) or
USB (
Ypage 235), additional information,
such as the weather at the destination, can
be displayed (
Ypage 176).
XTo exit Drive Information: press the con-
troller.
XPress the %button.
Route flight
XCall up the navigation menu (Ypage 133).
XTurn the controller until Route Flightis
brought to the front.
XPress the controller.
The route will then be flown along from a
helicopter view.
XTo exit the route flight: press the controller.
XPress the %button.
Info on navigation
XCall up the navigation menu (Ypage 133).
XTurn the controller until InfoonNaviga‐
tionis brought to the front.
XPress the controller.
The Digital Operator's Manual is opened at
the section on navigation.
134Navigation functions
Navigation

Call disconnection while the vehicle is
in motion
A call may be disconnected if:
Rthere is insufficient network coverage in
certain areas.
Ryou move from one transmitter/receiver
area (cell) into another and no channels are
free.
Ryou use a SIM card which is not compatible
with the network available.
Operating options
You can operate the telephone by:
Rusing the controller:
turning
sliding1 or4
pressing
Rusing the 6or~ button on the mul-
tifunction steering wheel
Rby voice using the Voice Control System
(see the manufacturer's operating instruc-
tions)
Unless stated otherwise, the descriptions and
illustrations in this section refer to COMAND.
Function restrictions
You may have to wait before using telephony
via COMAND in the following situations:
Rwhen the mobile phone is switched off
Rif Bluetooth®is switched off on the mobile
phone
Rif the mobile phone has not logged on to a
mobile phone network
Rif the Bluetooth®function is switched off in
COMAND
The telephone automatically tries to log on to a network. If no network is available, you may
not be able to make a " 911" emergency call.
If you attempt to make an outgoing call, the
No Service
message will appear for a short
while.
"911" emergency call
The following conditions must be fulfilled in
order to make a 911emergency call:
Ra valid and operational SIM card is inserted
in the mobile phone
Rthe mobile phone is switched on
Rthe PIN has been entered in the mobile
phone
Ra mobile phone network is available
Rthe mobile phone is connected to COMAND
via Bluetooth®
If you cannot make an emergency call, you
must arrange rescue measures yourself.
Making an emergency call:
XEnter the number on COMAND
(
Ypage 146).
XPress 6.
The telephone makes the connection.
XWait until the emergency call center
answers and describe the emergency sit-
uation.
Telephone menu
:Mobile phone network provider
;Signal strength of the mobile phone net-
work
=Receiver icon ¢or¡
?Telephone menu character bar
ABluetooth®device name of the currently
connected mobile phone
Telephone menu139
Telephone
Z

Deleting all speed dial presets
XTo callup th etelephon emenu: press th e
% button.
XTo cal lup th emen ubar :slid e6 thecon-
troller.
XTo selec tCal lLists:turn and press th e
controller .
XSelectSpeed Dia lPreset Lis t.
The speed dial list is displayed .
XTo highlight thedesire dmemor yposition :
turn th econtroller .
XTo selectG: slide9 thecontroller .
XTo selectDelete All Speed Dia lPre ‐
sets:turn and press th econtroller .
XTo selectYes:turn and press th econtroller .
Al lspeed dials are deleted.
or
XTo selec tNo:turn and press th econtroller .
The process is canceled.
Messages (text messages an de-
mails)
Prerequisites
To use th emessage functions, th econnecte d
mobile phone mus tsuppor tth eMA PBlue-
toot h
®profile. Whe nconnecting th emobile
phone ,you may hav eto accept th eprompt fo r
th eMA PBluetoot h
®profile.
Wit hsom emobile phones, som esetting sstill
hav eto be mad eafter connecting to
COMAN D(se eth emanufacturer's operatin g
instructions). The message sare displayed th e
next time you connec tto COMAND.
An e-mail accoun tmus tbe set up on th e
mobile phone fo rth ee-mail function (se eth e
manufacturer’s operatin ginstructions).
To rea dand writ ee-mail sin COMAND, th ee-
mail accoun tfirst needs to be configured
(
Ypage 159). Som
emobile phones wit hth eMAP Blue-
toot h
®profile:
Ronly sho wne wtext messages.
Rdo no tsuppor tth edeleting or editin gof
text messages.
Rdo no tsuppor tth edraft sfolder fo rtext
messages.
Rdo no tsuppor tth esendin gof text mes -
sages.
Rdo no tsuppor tth ee-mail function .
Rdo notsen dmessage sin alocke dstatus.
Not all mobile phone savailable on th emarke t
are equally suitable. You can obtain further
information about setti ngsa
nd supporte d
function sof Bluetoot h®-capablemobile
phone son th eInternet at
www.mercedes-benz-mobile.com .
You can also obtain more information by call-
ing.
In th eUSA, you can get in touch wit hth e
Mercedes-Ben zCustomer Assistanc eCente r
on 1-800-FOR-MERCedes (1-800-367-6372 ).
In Canada, you can get in touch with the Cus-
tomer Relations Center on 1-800-387-0100.
Function restrictions
Text messages cannot be written while the
vehicle is in motion.
General notes
New messages are identified by the /
symbol in the COMAND display and an audi-
ble signal. Once you have read all the mes-
sages, the symbol is no longer displayed.
COMAND displays the 100 newest text mes-
sages and e-mails.
The ú symbol is displayed when the
mobile phone's message memory is full. The
symbol is no longer displayed if you delete
messages.
158Messages (text messages and e-mails)
Telephone

A connection can be established by:
Rentering a web address (Ypage 190)
Rcalling up the Mercedes-Benz mobile web-
site (
Ypage 188)
Rcalling up a Mercedes-Benz App
(
Ypage 188)
Rcalling up a favorite
Restablishing an Internet connection via a
wireless networking device. The "Allow
shared WiFi usage" option must be activa-
ted on COMAND for this (
Ypage 52)
Ending the connection
XPress Cancelin the connections window.
Connection status
:Display of existing connection and signal
strength of the mobile phone network
In most cases, the current connection status
is then shown in the status bar when you
switch to another main function.
Detailed connection status
XTo display the main function bar: slide 5
the controller.
XTo select ®: turn and press the controller.
The menu with the Internet functions is dis- played.
XTo switch to the menu bar: slide 6the
controller.
XTo select Settings: turn and press the
controller.
XTo select Connection Status: turn and
press the controller.
The following information is displayed:
Rthe volume of transferred data
Rconnection status
Rthe device name of the mobile phone
Ending the connection
USA: you cannot cancel the connection your-
self. The Internet connection is automatically
terminated if the system does not recognize
any user input within a five-minute time
period.
Canada:
XTo display the main function bar: slide 5
the controller.
XTo select ®: turn and press the controller.
The menu with the Internet functions is dis-
played.
XTo switch to the menu bar: slide 6the
controller.
XTo select the scissors symbol: turn and
press the controller.
If the mobile phone Internet connection is
canceled, COMAND tries to reconnect. You
should therefore always close the connection
on COMAND.
Google™ local search
Calling up Local Search
182Google™ local search
Online and Internet functions

Quick save
XPress and hold a number key, e.g.l,
until a tone sounds. The station is saved to
second place in the radio station presets.
Storing current stations
XIn radio mode: slide 6the controller.
The radio menu bar appears.
XTo select Presets: turn and press the con-
troller.
XTo select the Save Current Station/
Channeloption: turn and press the con-
troller.
XTo select the position of the required pre-
set: turn and press the controller.
or
XSelect the Edit Station Presetoption.
XSelect the position of the required preset:
turn the controller.
This can also be a preset position that is
already occupied, which is then overwritten
by the current station.
XSlide9the controller.
An additional menu appears.
XTo select the Save Current Station/
Channeloption: turn and press the con-
troller.
The currently set station is stored in the
selected preset position. A tone signals a
successful preset entry. or
XIn the main display field, press and hold the
controller.
A list of current allocated preset positions
appears.
XTo select the position of the required preset
and confirm: turn the controller and press.
or
XIn radio mode: slide 6the controller.
XTo select Presets: turn and press the con-
troller.
XTo select Save Current Station/Chan‐
nel: turn and press the controller.
The currently set station is stored in the
selected preset position. A tone signals a
successful preset entry.
Moving highlighted stations
XIn radio mode: slide 6the controller.
XTo select Presets: turn and press the con-
troller.
XSelect Edit Station Preset.
XTo select the required preset entry: turn the
controller.
XSlide9the controller.
An additional menu appears.
XTo select Move Highlighted Station/
Channel: turn and press the controller.
The list of stored stations appears again.
XTo move the highlighted station to and
press the new position: turn the controller.
Deleting highlighted stations
XIn radio mode: slide 6the controller.
XTo select Presets: turn and press the con-
troller.
XSelect Edit Station Preset.
XTo select the required preset entry: turn the
controller.
XSlide9the controller.
An additional menu appears.
200Station
Radio