2016 MERCEDES-BENZ S CLASS light

If you come into contact with the electrolyte,
observe the following: R
Rinse off the electrolyte from your skin
immediately with water. R
Immediately rinse the electrolyte out of
your eyes thoroughly with clean water. R
If the electrolyte is swallowed, immediately
rinse your mouth out thoroughly. Do not
induce vomiting. R
If electrolyte comes into contact with your
skin or hair or is swallowed, seek medical
attention immediately. R
Immediately change out of clothing which
has come into contact with electrolyte. R
If an allergic reaction occurs, seek medical
attention immediately.
The rear-view mirror and the exterior mirror on
the driver's side automatically go into anti-glare
mode if the following conditions are met simul-
taneously: R
the ignition is switched on R
incident light from headlamps strikes the sen-
sor in the rear-view mirror.
The mirrors do not go into anti-glare mode if
reverse gear is engaged or if the interior lighting
is switched on.
Parking position for the exterior mir-
ror on the front-passenger side
Setting and storing the parking position You can position the front-passenger side exte-
rior mirror in such a way that you can see the
rear wheel on that side as soon as you engage
reverse gear. You can store this position. Using reverse gear
C
Memory button MD
Adjustment button

Useful information
i This Operator's Manual describes all models
and all standard and optional equipment of
your vehicle available at the time of publica-
tion of the Operator's Manual. Country-spe-
cific differences are possible. Please note
that your vehicle may not be equipped with all
features described. This also applies to
safety-related systems and functions.
i Read the information on qualified specialist
workshops ( Y
page 28).
Exterior lighting
General notes For reasons of safety, Mercedes-Benz recom-
mends that you drive with the lights switched on
even during the daytime. In some countries,
operation of the headlamps varies due to legal
requirements and self-imposed obligations.
Setting the exterior lighting
Setting options Exterior lighting can be set using: R
the light switch R
the combination switch ( Y
page 131)R
the on-board computer ( Y
page 274)
Light switch
Operation
G c
Left-hand standing lamps
H d
Right-hand standing lamps I `
Parking lamps, license plate and
instrument cluster lightingJ X
Automatic headlamp mode, controlled
by the light sensorK X
Low-beam/high-beam headlamps
If you hear a warning tone when you leave the
vehicle, the lights may still be switched on. X
Turn the light switch to the X position.
The exterior lighting (except the parking/stand-
ing lamps) switches off automatically if you: R
remove the SmartKey from the ignition lock R
open the driver's door with the SmartKey in
position 0 in the ignition lock
Automatic headlamp mode
G WARNING
When the light switch is set to X , the low-
beam headlamps may not be switched on
automatically if there is fog, snow or other
causes of poor visibility due to the weather
conditions such as spray. There is a risk of an
accident.
In such situations, turn the light switch to
X .
The automatic headlamp feature is only an aid.
The driver is responsible for the vehicle's light-
ing at all times.
Canada only:
The daytime running lamps improve the visibility
of your vehicle during the day. The daytime run-
ning lamps function is required by law in Can-
ada. It cannot therefore be deactivated.
When the engine is running and the vehicle is
stationary: if you move the selector lever from a
drive position to P , the daytime running lamps/
low-beam headlamps go out after three
minutes.
When the engine is running, the vehicle is sta-
tionary and in bright ambient light: if you turn the
light switch to the ` position, the daytime
running lamps and parking lamps switch on.
If the engine is running and you turn the light
switch to the X position, the manual settings
take precedence over the daytime running
lamps.
USA only:
The daytime running lamps improve the visibility
of your vehicle during the day. Here, the Day‐130
Exterior lighting
Lights and windshield wipers

time Running Lights function must be
switched on via the on-board computer
( Y
page 274).
If the engine is running and you turn the light
switch to the ` or X position, the manual
settings take precedence over the daytime run-
ning lamps.
X is the favored light switch setting. The light
setting is automatically selected according to
the brightness of the ambient light (exception:
poor visibility due to weather conditions such as
fog, snow or spray): R
SmartKey in position 1 in the ignition lock: the
parking lamps are switched on or off auto-
matically depending on the brightness of the
ambient light. R
With the engine running: if you have switched
on the Daytime Running Lights function in
the on-board computer, the daytime running
lamps or the parking lamps and low-beam
headlamps are switched on or off automati-
cally depending on the brightness of the ambi-
ent light. X
To switch on the automatic headlamps:
turn the light switch to the X position.
Low-beam headlamps Even if the light sensor does not detect that it is
dark, the parking lamps and low-beam head-
lamps switch on when the ignition is switched on
and the light switch is set to the X position.
This is a particularly useful function in the event
of rain and fog. X
To switch on the low-beam headlamps:
turn the SmartKey in the ignition lock to posi-
tion 2 or start the engine.X
Turn the light switch to the X position.
The green X indicator lamp in the instru-
ment cluster lights up.
Parking lamps
! If the battery charge is very low, the parking
lamps or standing lamps are automatically
switched off to enable the next engine start.
Always park your vehicle safely and suffi-
ciently lit according to legal standards. Avoid
using the parking lamps ` over a period of
several hours. If possible, switch on the right-
hand d or left-hand c standing lamp. X
To switch on: turn the light switch to the
` position.
The green ` indicator lamp in the instru-
ment cluster lights up.
Standing lamps Switching on the standing lamps ensures the
corresponding side of the vehicle is illuminated. X
To switch on the standing lamps: the
SmartKey should not be in the ignition lock or
it should be in position 0 .X
Turn the light switch to the c (left-hand
side of the vehicle) or d ((right-hand side
of the vehicle) position.
Combination switch
Turn signal
C
High-beam headlamps D
Turn signal, right

High-beam headlamps X
To activate manually: turn the SmartKey in
the ignition lock to position 2 or start the
engine. X
Vehicles without Adaptive Highbeam Assist
Plus: turn the light switch to position X or
X .X
Vehicles with Adaptive Highbeam Assist Plus:
turn the light switch to the X position.X
Press the combination switch beyond the
pressure point in the direction of arrow C .
In the X position, the high-beam head-
lamps are only switched on when it is dark and
the engine is running.
The blue W indicator lamp in the instru-
ment cluster lights up when the high-beam
headlamps are switched on. X
To switch off: move the combination switch
back to its normal position.
The blue W indicator lamp in the instru-
ment cluster goes out.
Vehicles with Adaptive Highbeam Assist
Plus: if Adaptive Highbeam Assist Plus is acti-
vated, it automatically controls activation and
deactivation of the high-beam headlamps
( Y
page 133).
High-beam flasher X
To switch on: turn the SmartKey in the igni-
tion lock to position 1 or 2 , or start the engine.X
Pull the combination switch in the direction of
arrow

Adaptive Highbeam Assist Plus
Gene ra l notes
Wit h Adaptive Highbea m Assis t Plus, you can
automatically switch between low-beam , partial
high-beam and high-beam headlamps.
Partial high-beam is a for m of illumination
whereby th e high-beam is directe d past other
road users. Other road user s are kept out of th e
high-beam. This prevents glare. When there is a
vehicl e in front, for example, th e high-beam
headlamp s illuminate th e areas to it s right and
left, and th e vehicl e in fron t is illuminate d by th e
low-beam headlamps.
The system automatically adapt s th e low-beam
headlamp range depending on th e distanc e to
th e other vehicle. Once th e system no longer
detects any other vehicles, it reactivates th e
high-beam headlamps.
If th e high-beam or partial high-beam are caus -
ing to o muc h reflection from traffic signs, th e
lights are automatically dimmed and glar e for
th e driver caused by th e reflection s is thus avoi -
ded.
The system' s optical sensor is locate d behind
th e windshield near th e overhead control panel. Import ant safety notes
G WARNIN G
Adaptive Highbea m Assis t Plus does no t rec -
ogniz e road users: R
who hav e no lights , e.g. pedestrian sR
who hav e poor lighting , e.g. cyclist sR
whos e lighting is blocked, e.g. by a barrier
In ver y rar e cases, Adaptive Highbea m Assis t
Plus may no t recogniz e road user s who do
hav e lights , or may recogniz e them to o late. In
this or similar situations, th e automatic high -
beam headlamp s will no t be deactivated or
will be activated regardless . There is a ris k of
an accident.
Always carefully observ e th e traffic condition s
and switch off th e high-beam headlamp s in
goo d time.
Adaptive Highbea m Assis t Plus canno t tak e int o
accoun t road , weather or traffic conditions.
Adaptive Highbea m Assis t Plus is only an aid.
You are responsibl e for adjusting th e vehicle's
lighting to th e prevailing light, visibilit y and traf-
fic conditions.
In particular, th e detection of obstacles can be
restricted if there is: R
poor visibility, e.g. due to fog , heav y rain or
snow R
dir t on th e sensor s or th e sensor s are
obscured
Switching Adaptive Highbeam Assist
PLUS on/off
C
High-beam headlamp s
D
Turn signal, rightExterior lighting 133
Lights and windshield wipers Z

Problems with the windshield wipers Problem
Possible causes/consequences and P Solutions
The windshield wipers
are jammed. Leaves or snow, for example, may be obstructing the windshield wiper
movement. The wiper motor has been deactivated. X
Switch off the engine using the Start/Stop button and open the
driver's door. X
Remove the cause of the obstruction. X
Switch the windshield wipers back on.
The windshield wipers
fail completely. The windshield wiper drive is malfunctioning. X
Select another wiper speed on the combination switch. X
Have the windshield wipers checked at a qualified specialist work-
shop.
The wiper motor has been deactivated. X
Switch off the engine using the Start/Stop button and open the
driver's door. X
Remove the cause of the obstruction. X
Switch the windshield wipers back on.
For a standard wiper sys-
tem only: the windshield
washer fluid from the
spray nozzles no longer
hits the center of the
windshield. The spray nozzles are misaligned. X
Have the spray nozzles adjusted at a qualified specialist workshop. Windshield wipers 139
Lights and windshield wipers Z

Notes on using automatic climate
control
Climate control system Below, you can find a number of notes and rec-
ommendations to help you use climate control
optimally. R
Activate climate control using the X
rocker switch. The indicator lamp in the X
rocker switch lights up. R
Set the temperature to 72 ‡ (22 †). R
Only use the "Windshield defrosting" function
briefly until the windshield is clear again. R
Only use air-recirculation mode briefly, e.g. if
there are unpleasant outside odors or when in
a tunnel. The windows could otherwise fog up,
since no fresh air is drawn into the vehicle in
air-recirculation mode. R
Use the residual heat function if you want to
heat or ventilate the vehicle interior when the
ignition is switched off. The residual heat
function can only be activated or deactivated
with the ignition switched off. The residual
heat function is switched off when the ignition
is switched on.
If you are controlling the rear-compartment cli-
mate control using the front control panel, note
the following: R
If you set rear-compartment climate control
using the front control panel, the

X
To switch on: press the X rocker switch
on the front control unit up or down.
or X
Activate automatic mode via the air-condi-
tioning setting bar in the multimedia system
(see the separate operating instructions).
The indicator lamp in the X rocker switch
lights up.
i Select the temperature and automatic
mode immediately thereafter. Otherwise, you
will have to select "Rear adjustment" again
from the air-conditioning setting bar before
activating automatic mode. X
To switch to manual operation: press the