2016 MAZDA MODEL CX-5 maintenance

Black plate (477,1)
CAUTION
A wrong-sized wheel may adversely
affect:
ØTire fit
ØWheel and bearing life
ØGround clearance
ØSnow-chain clearance
ØSpeedometer calibration
ØHeadlight aim
ØBumper height
ØTire Pressure Monitoring System
NOTE
lWhen replacing a wheel, make sure the new
one is the same as the original factory
wheel in diameter, rim width, and offset
(inset/outset).
lFor details, contact an Authorized Mazda
Dealer.
Proper tire balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tires can cause
vibration and uneven wear, such as
cupping and flat spots.
Maintenance and Care
Owner Maintenance
6-45
CX-5_8DV2-EA-14K_Edition3 Page477
Thursday, February 26 2015 5:34 PM
Form No.8DV2-EA-14K

Black plate (478,1)
Light Bulbs
With LED headlights
With halogen headlights
Rear side-marker lights
Rear turn signal lights
Brake lights/Taillights
License plate lights Headlights (Low beam)
High-mount brake light
Rear side-marker lights
Rear turn signal lights Brake lights/Taillights
License plate lights
High-mount brake light
Side turn
signal lights
Front turn signal lights/
Front side-marker lights
Headlights (High beam)/
Daytime running lights Headlights (Low beam) Front turn signal lights/
Parking lights (Front side-
marker lights)
Fog lights
Rear map lights
Overhead light (Front)/
Map lights Luggage compartment light
Vanity mirror lights
Rear map lights
Overhead light (Front)/
Map lights Luggage compartment light
Vanity mirror lights
Daytime running lights/
Parking lights
Fog lights
Some models.
Side turn
signal lights
Headlights (High beam)
Taillights (Liftgate side)
Taillights (Liftgate side)
Reverse lights
Reverse lights Taillights
6-46
Maintenance and Care
Owner Maintenance
CX-5_8DV2-EA-14K_Edition3 Page478
Thursday, February 26 2015 5:34 PM
Form No.8DV2-EA-14K

Black plate (479,1)
WARNING
Never touch the glass portion of a
halogen bulb with your bare hands and
always wear eye protection when
handling or working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when
lit.
Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb
or breaking it some other way.
CAUTION
When removing the lens or lamp unit
using a flathead screwdriver, make
sure that the flathead screwdriver
does not contact the interior
terminal. If the flathead screwdriver
contacts the terminal, a short circuit
may occur.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
qReplacing Exterior Light Bulbs
Headlights (With LED headlights)
Low-beam bulbs, High-beam bulbs,
Daytime running lights/Parking lights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Headlights (With halogen headlights)
Low-beam bulbs, High-beam bulbs/
Daytime running lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the hood.
3.(Right side)
Remove the windshield washer fluid
reservoir from the guide.
Windshield washer
fluid reservoir Guide
4. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector downward.
Maintenance and Care
Owner Maintenance
6-47
CX-5_8DV2-EA-14K_Edition3 Page479
Thursday, February 26 2015 5:34 PM
Form No.8DV2-EA-14K

Black plate (480,1)
Low-beam bulbs
High-beam bulbs/Daytime running
lights
5. Turn the socket and bulb assembly to
remove it. Carefully remove the bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.Low-beam bulbs
High-beam bulbs/Daytime running
lights
6. Install the new bulb in the reverse order
of the removal procedure.
Front turn signal lights/Front side-
marker lights (With LED headlights)
Front turn signal lights/Parking lights
(Front side-marker lights) (With
halogen headlights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
6-48
Maintenance and Care
Owner Maintenance
CX-5_8DV2-EA-14K_Edition3 Page480
Thursday, February 26 2015 5:35 PM
Form No.8DV2-EA-14K

Black plate (481,1)
3. Pull the center of each plastic retainer
and remove the retainers.
InstallationRemoval
4. Turn the screw counterclockwise and
remove it, and then partially peel back
the mudguard.
5. Turn the socket and bulb assembly
counterclockwise and remove it.6. Disconnect the bulb from the socket.
7. Install the new bulb in the reverse order
of the removal procedure.
Fog lights (With LED headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Fog lights (With halogen headlights)í
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
Maintenance and Care
Owner Maintenance
6-49íSome models. CX-5_8DV2-EA-14K_Edition3 Page481
Thursday, February 26 2015 5:35 PM
Form No.8DV2-EA-14K

Black plate (482,1)
3. Pull the center of each plastic retainer
and remove the retainers.
InstallationRemoval
4. Turn the screw counterclockwise and
remove it, and then partially peel back
the mudguard.
5. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector downward.
6. Turn the socket and bulb assembly to
remove it. Carefully remove the bulb
from its socket in the reflector by
gently pulling it straight back out of the
socket.
7. Install the new bulb in the reverse order
of the removal procedure.
Side-turn signal lights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
6-50
Maintenance and Care
Owner Maintenance
CX-5_8DV2-EA-14K_Edition3 Page482
Thursday, February 26 2015 5:35 PM
Form No.8DV2-EA-14K

Black plate (483,1)
Brake lights/Taillights, Rear side-
marker lights, Taillights, Rear turn
signal lights, Reverse lights (With LED
headlights)
Brake lights/Taillights, Rear side-
marker lights, Taillights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Rear turn signal lights, Reverse lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover with a cloth-
wrapped flathead screwdriver to the
cover.
Rear turn signal lights
Reverse lights
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
Rear turn signal lights
Reverse lights
Maintenance and Care
Owner Maintenance
6-51
CX-5_8DV2-EA-14K_Edition3 Page483
Thursday, February 26 2015 5:35 PM
Form No.8DV2-EA-14K

Black plate (484,1)
5. Install the new bulb in the reverse order
of the removal procedure.
Brake lights/Taillights, Rear turn signal
lights, Rear side-marker lights,
Taillights (Liftgate side), Reverse lights
(With halogen headlights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover with a cloth-
wrapped flathead screwdriver to the
cover.
Brake lights/Taillights, Rear turn signal
lights, Rear side-marker lights
Taillights (Liftgate side), Reverse lights
3. Turn the socket and bulb assembly
counterclockwise and remove it.4. Disconnect the bulb from the socket.
Brake lights/Taillights
Rear turn signal lights
Rear side-marker lights
6-52
Maintenance and Care
Owner Maintenance
CX-5_8DV2-EA-14K_Edition3 Page484
Thursday, February 26 2015 5:35 PM
Form No.8DV2-EA-14K