2016 MAZDA MODEL CX-3 warning light

3–41
Before Driving
Driving Tips
Rocking the Vehicle
WARNING
Do not spin the wheels at more than
56 km/h (35 mph), and do not allow
anyone to stand behind a wheel when
pushing the vehicle:
When the vehicle is stuck, spinning the
wheels at high speed is dangerous.
The spinning tire could overheat and
explode. This could cause serious
injuries.
CAUTION
Too much rocking may cause engine
overheating, transaxle failure, and tire
damage.
If you must rock the vehicle to free it from
snow, sand or mud, depress the accelerator
slightly and slowly move the shift lever
from D to R.
Winter Driving
Carry emergency gear, including tire
chains, window scraper, fl ares, a small
shovel, jumper cables, and a small bag of
sand or salt.
Ask an Authorized Mazda Dealer to check
the following:
 


y Have the proper ratio of antifreeze in the
radiator.
  Refer to Engine Coolant on page 6-29 .



y Inspect the battery and its cables. Cold
reduces battery capacity.
 


y Use an engine oil appropriate for the
lowest ambient temperatures that the
vehicle will be driven in (page 6-27 ).
 


y Inspect the ignition system for damage
and loose connections.
 


y Use washer fl uid made with antifreeze—
but do not use engine coolant antifreeze
for washer fl uid (page 6-31 ).
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










3–42
Before Driving
Driving Tips
NOTE
 


y Do not use the parking brake in freezing
weather as it may freeze. Instead, shift
to P and block the rear wheels.
 


y Remove snow before driving. Snow left
on the windshield is dangerous as it
could obstruct vision.
 


y Do not apply excessive force to a
window scraper when removing ice or
frozen snow on the mirror glass and
windshield.
 


y Never use warm or hot water for
removing snow or ice from windows and
mirrors as it could result in the glass
cracking.
 


y Drive slowly. Braking performance
can be adversely affected if snow or
ice adheres to the brake components. If
this situation occurs, drive the vehicle
slowly, releasing the accelerator pedal
and lightly applying the brakes several
times until the brake performance
returns to normal.
Snow Tires
Use snow tires on all four wheels
Do not go faster than 120 km/h (75 mph)
while driving with snow tires. Infl ate snow
tires 30 kPa (0.3 kgf/cm
2 , 4.3 psi) more
than recommended on the tire pressure
label (driver's door frame), but never
more than the maximum cold-tire pressure
shown on the tires.
Except Mexico
The vehicle is originally equipped with
all season radials designed to be used all
year around. In some extreme climates you
may fi nd it necessary to replace them with
snow tires during the winter months to
further improve traction on snow and ice
covered roads.
Mexico
The vehicle is originally equipped with
summer tires designed for optimum
traction on wet and dry roads. If your
vehicle is to be used on snow and ice
covered roads, Mazda recommends that
you replace the tires originally equipped
on your vehicle with snow tires during the
winter months.
WARNING
Use only the same size and type tires
(snow, radial, or non-radial) on all four
wheels:
Using tires diff erent in size or type is
dangerous. Your vehicle's handling
could be greatly aff ected and result in
an accident.
CAUTION
Check local regulations before using
studded tires.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










3–43
Before Driving
Driving Tips
Tire Chains
Check local regulations before using tire
chains.
CAUTION
 


¾ Chains may aff ect handling.



¾ Do not go faster than 50 km/h (30
mph) or the chain manufacturer's
recommended limit, whichever is lower.
 


¾ Drive carefully and avoid bumps, holes,
and sharp turns.
 


¾ Avoid locked-wheel braking.



¾ Do not use chains on a temporary spare
tire; it may result in damage to the
vehicle and to the tire.
 


¾ Do not use chains on roads that are free
of snow or ice. The tires and chains could
be damaged.
 


¾ Chains may scratch or chip aluminum
wheels.
NOTE
If your vehicle is equipped with the tire
pressure monitoring system, the system
may not function correctly when using tire
chains.
Install the chains on the front tires only.
Do not use chains on the rear tires.
Please consult an Authorized Mazda
Dealer.
Installing the chains
1. If your vehicle is equipped with wheel
covers remove them, otherwise the
chain bands will scratch them.
2. Secure the chains on the front tires as
tightly as possible.
Always follow the chain manufacturer's
instructions.
3. Retighten the chains after driving
1/2—1 km (1/4—1/2 mile).
Driving In Flooded Area
WARNING
Dry off brakes that have become
wet by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the brake
performance returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been aff ected.
CAUTION
Do not drive the vehicle on fl ooded
roads as it could cause short circuiting
of electrical/electronic parts, or
engine damage or stalling from
water absorption. If the vehicle has
been immersed in water, consult an
Authorized Mazda Dealer.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










*Some models.4–1
4When Driving
Information concerning safe driving and stopping.



Start/Stop Engine ................................ 4-4
Ignition Switch ............................... 4-4
Starting the Engine ......................... 4-5
Turning the Engine Off ................ 4-10
Instrument Cluster and Display ...... 4-12
Meters and Gauges ....................... 4-12
Active Driving Display
* ............... 4-22
Warning/Indicator Lights ............. 4-24
Transaxle ............................................ 4-30
Automatic Transaxle Controls ...... 4-30
Switches and Controls ...................... 4-41
Lighting Control ........................... 4-41
Fog Lights
* ................................... 4-46
Turn and Lane-Change Signals ...... 4-46
Windshield Wipers and Washer ...... 4-47
Rear Window Wiper and
Washer .......................................... 4-51
Rear Window Defogger ............... 4-52
Horn ............................................. 4-53
Hazard Warning Flasher ............... 4-53
Brake .................................................. 4-54
Brake System ............................... 4-54
Hill Launch Assist (HLA)
* ........... 4-56
ABS/TCS/DSC ................................... 4-58
Antilock Brake System (ABS) ...... 4-58
Traction Control System (TCS) ...... 4-59
Dynamic Stability Control
(DSC) ........................................... 4-61 Fuel Economy Monitor ..................... 4-62
Fuel Economy Monitor
* ............... 4-62
Drive Selection ................................... 4-64
Drive Selection ............................. 4-64
AWD ................................................... 4-66
All-Wheel Drive (AWD)
Operation ...................................... 4-66
Power Steering................................... 4-67
Power Steering ............................. 4-67
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










*Some models.4–2
i-ACTIVSENSE................................. 4-68
i-ACTIVSENSE*.......................... 4-68
Adaptive Front Lighting System
(AFS)
* .......................................... 4-70
High Beam Control System
(HBC)
*.......................................... 4-71
Lane Departure Warning System
(LDWS)
* ...................................... 4-74
Blind Spot Monitoring (BSM)
System
* ......................................... 4-80
Distance Recognition Support System
(DRSS)
* ........................................ 4-87
Rear Cross Traffi c Alert
(RCTA)
* ....................................... 4-90
Mazda Radar Cruise Control
(MRCC)
* ...................................... 4-93
Smart City Brake Support
(SCBS)
* ...................................... 4-104
Smart Brake Support (SBS)* ...... 4-109
Forward Sensing Camera (FSC)* .... 4-112
Radar Sensor (Front)* ................. 4-115
Laser Sensor (Front)* ................. 4-118
Radar Sensors (Rear)* ................ 4-120
Cruise Control ................................. 4-122
Cruise Control
* ........................... 4-122
Tire Pressure Monitoring System .. 4-126
Tire Pressure Monitoring
System
* ....................................... 4-126
Rear View Monitor .......................... 4-130
Rear View Monitor
* ................... 4-130
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–4
When Driving
Start/Stop Engine
Ignition Switch
Push Button Start Positions
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
Each time the push button start is pressed,
the ignition switches in the order of off,
ACC, and ON. Pressing the push button
start again from ON switches the ignition
off.
Push button startIndicator light
NOTE
 


y The engine starts by pressing the push
button start while depressing the brake
pedal. To switch the ignition position,
press the push button start without
depressing the pedal.
 


y Do not leave the ignition switched ON
while the engine is not running. Doing
so could result in the battery going
dead. If the selector lever is in the P
position, and the ignition is in ACC, the
ignition switches off automatically after
about 25 minutes. Off
The power supply to electrical devices
turns off and the push button start indicator
light (amber) also turns off.
In this position the steering wheel is
locked.
WARNING
Before leaving the driver's seat, always
switch the ignition off , set the parking
brake, and make sure the selector lever
is in P:
Leaving the driver's seat without
switching the ignition off , setting the
parking brake, and shifting the selector
lever to P is dangerous. Unexpected
vehicle movement could occur which
could result in an accident.
In addition, if your intention is to leave
the vehicle for even a short period, it
is important to switch the ignition off ,
as leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.
ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
NOTE
The keyless entry system does not function
while the push button start has been
pressed to ACC, and the doors will not
lock/unlock even if they have been locked
manually.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–5
When Driving
Start/Stop Engine
O N
This is the normal running position after
the engine is started. The indicator light
(amber) turns off. (The indicator light
(amber) illuminates when the ignition
is switched ON and the engine is not
running.)
Some indicator lights/warning lights
should be inspected before the engine is
started (page 4-24 ).
NOTE
When the push button start is pressed to
ON, the sound of the fuel pump motor
operating near the fuel tank can be heard.
This does not indicate an abnormality.
Starting the Engine
WARNING
Radio waves from the key may aff ect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will aff ect
the device.
NOTE
 


y The key must be carried because the key
carries an immobilizer chip that must
communicate with the engine controls at
short range.
 


y The engine can be started when the
push button start is pressed from off,
ACC, or ON.
 


y The push button start system functions
(function which can start the engine
by only carrying the key) can be
deactivated to prevent any possible
adverse effect on a user wearing a
pacemaker or other medical device. If
the system is deactivated, you will be
unable to start the engine by carrying
the key. Consult an Authorized Mazda
Dealer for details. If the push button
start system functions have been
deactivated, you can start the engine by
following the procedure indicated when
the key battery goes dead.
  Refer to Engine Start Function When
Key Battery is Dead on page 4-8 .
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–7
When Driving
Start/Stop Engine
CAUTION
If the KEY warning light (red)
illuminates, or the push button
start indicator light (amber) fl ashes,
this could indicate a problem with
the engine starting system and the
inability to start the engine or switch
the ignition to ACC or ON. Have your
vehicle inspected at an Authorized
Mazda Dealer as soon as possible.
NOTE
 


y Under the following conditions, the
KEY warning light (red) fl ashes after
the push button start is pressed to
inform the driver that the push button
start will not switch to ACC even if it is
pressed from off.
 


y The key battery is dead.



y The key is out of operational range.



y The key is placed in areas where it is
diffi cult for the system to detect the
signal (page 3-7 ).
 


y A key from another manufacturer
similar to the key is in the
operational range.
.
y(Forced engine starting method)
 If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) fl ashes, this
could indicate that the engine may not
start using the usual starting method.
Have your vehicle inspected at an
Authorized Mazda Dealer as soon as
possible. If this occurs, the engine can
be force-started. Press and hold the
push button start until the engine starts.
Other procedures necessary for starting
the engine such as having the key in the
cabin, and depressing the brake pedal
are required.
 


y When the engine is force-started,
the KEY warning light (red) remains
illuminated and the push button
start indicator light (amber) remains
fl ashing.
 


y When the selector lever is in the neutral
(N) position, the KEY indicator light
(green) and the push button start
indicator light (green) do not illuminate.
7. Press the push button start after both
the KEY indicator light (green) in the
instrument cluster and the push button
start indicator light (green) illuminate.
NOTE
 


y After starting the engine, the push
button start indicator light (amber)
turns off and the ignition switches to the
ON position.
 


y After pressing the push button start and
before the engine starts, the operation
sound of the fuel pump motor from near
the fuel tank can be heard, however, this
does not indicate a malfunction.
8. After starting the engine, let it idle for
about ten seconds.
NOTE
 


y Whether the engine is cold or warm, it
should be started without the use of the
accelerator.
 


y If the engine does not start the fi rst
time, refer to Starting a Flooded Engine
under Emergency Starting. If the engine
still does not start, have your vehicle
inspected by an Authorized Mazda
Dealer (page 7-21 ).
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC