2016 MAZDA MODEL CX-3 light

4–98
When Driving
i-ACTIVSENSE
How to Set the Speed
1. Adjust th-e vehicle speed to the desired
setting using the accelerator pedal.
2. Headway control begins when the
SET
or SET switch is pressed. The
set speed and the inter-vehicle distance
display fi lled with white lines are
displayed. The Mazda Radar Cruise
Control (MRCC) indicator light (green)
is indicated simultaneously.
Travel status Display
During travel at constant
speed
During travel under
headway control
NOTE
 


y If a vehicle ahead is detected while
traveling at a constant speed, the
vehicle-ahead indication is displayed
and headway control is performed.
Additionally, when a vehicle ahead is
no longer detected, the vehicle-ahead
indication turns off and the system
switches back to travel at constant
speed.
 


y If you are driving the vehicle at a speed
faster than the set speed, headway
control on the vehicle ahead is not
possible Adjust the system to the desired
vehicle speed using the accelerator
pedal.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–10 0
When Driving
i-ACTIVSENSE
NOTE
 


y When accelerating using the SET
switch while in headway control, the set
vehicle speed can be adjusted but
acceleration is not possible. If there is
no longer a vehicle ahead, acceleration
continues until reaching the set vehicle
speed. Check the set vehicle speed by
viewing the set vehicle speed display in
the active driving display.
 


y When depressing the accelerator pedal,
the inter-vehicle distance display in the
active driving display changes to the
white-line display.
 


y The minimum settable speed is 30 km/h
(19 mph). If the set vehicle speed
reaches 30 km/h (19 mph) using the
switch operation, constant speed travel
is maintained at about 30 km/h (19
mph) even if the SET
switch is
pressed. The Mazda Radar Cruise
Control (MRCC) system is not canceled.
To Deactivate
The Mazda Radar Cruise Control (MRCC)
is canceled when the OFF switch is
pressed.
When the system is temporarily
canceled
In the following cases, the Mazda Radar
Cruise Control (MRCC) system is
temporarily canceled. The Mazda Radar
Cruise Control (MRCC) indicator light
(green) turns off simultaneously.
 


y The CANCEL switch is pressed.



y The brake pedal is depressed.



y The parking brake is applied.



y
 
The selector lever is shifted to park (P),
neutral (N) or reverse (R).
 


y In the following cases, the beep sounds
one time.
 

y
 The vehicle speed decreases to less
than 25 km (16 mph).
 

y
 The DSC has operated.


y
 The TCS has operated for a certain
period of time.
 

y
 The Smart City Brake Support (SCBS)
has operated.
 

y
 The Smart Brake Support (SBS) has
operated.
 

y
 When traveling on a down slope for a
long period of time.
 

y
 There is a problem with the system.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–102
When Driving
i-ACTIVSENSE
Switching to cruise control function
When the ON switch is pressed
continuously for about 2 seconds while
the Mazda Radar Cruise Control (MRCC)
system is turned on, the system is switched
to the cruise control function.
The Mazda Radar Cruise Control (MRCC)
indicator light (green) in the instrument
cluster turns off and the cruise control
indication is displayed in the active
driving display.
WARNING
Always turn off the cruise control
function when it is not in use:
Leaving the cruise control function
turned on when it is not in use
is dangerous as it could operate
unexpectedly, resulting in an accident.
How to set the speed
Adjust the system to the desired vehicle
speed using the accelerator pedal.
Cruise control function begins when the
SET
or SET switch is pressed.
NOTE
 


y The system may not be able to maintain
the set speed constantly depending on
driving conditions such as steep up or
down slopes.
 


y The speed will continue increasing
while the SET
switch is pressed and
held. The speed will continue
decreasing while the SET
switch is
pressed and held.
How to increase the set speed
The set speed can be increased using the
following operations:
To increase speed using the SET
switch
Press and hold the SET
switch and
release the switch at the desired speed.
The set speed can be adjusted
incrementally (1 km/h (1 mph)
increments) by pressing the switch and
releasing it immediately. For example, if
the switch is pressed 4 times, the set speed
increases by about 4 km/h (4 mph).
To increase speed using accelerator
pedal
Depress the accelerator pedal and press the
SET
or SET switch at the desired
speed.
If the switch is not operated, the system
returns to the set speed after you release
your foot from the accelerator pedal.
How to Decrease the Set Speed
Press the SET
switch continuously and
release the switch at the desired speed.
The set speed can be adjusted
incrementally (1 km/h (1 mph) increments)
by pressing the switch and releasing it
immediately. For example, if the switch
is pressed 4 times, the set vehicle speed
decreases by about 4 km/h (4 mph).
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–106
When Driving
i-ACTIVSENSE
CAUTION
 


¾ When driving off -road in areas where there is grass or forage, it is recommended that the
Smart City Brake Support (SCBS) system be turned off .




¾ Always use tires for all wheels that are of the specifi ed size, and the same manufacturer,
brand, and tread pattern. In addition, do not use tires with signifi cantly diff erent wear
patterns on the same vehicle as the Smart City Brake Support (SCBS) system may not
operate normally.
 


¾ The laser sensor (front) includes a function for detecting a soiled windshield and informing
the driver, however, depending on the conditions, it may not detect plastic shopping bags,
ice or snow on the windshield. In such cases, the system cannot accurately determine a
vehicle ahead and may not be able to operate normally. Always drive carefully and pay
attention to the road ahead.
NOTE
 


y The Smart City Brake Support (SCBS) system will not operate if the driver is deliberately
performing driving operations (accelerator pedal and steering wheel).
 


y The Smart City Brake Support (SCBS) system will operate under the following conditions.




y The engine is running.



y The Smart City Brake Support (SCBS) warning light (amber) does not illuminate.



y The vehicle speed is between about 4 to 30 km/h (2 to 18 mph).



y The Smart City Brake Support (SCBS) system is not turned off.



y The DSC is not malfunctioning.




y The Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-infrared
laser beam and receiving the beam refl ected off the refl ector of the vehicle ahead, and
then using it for the measurement. Consequently, the Smart City Brake Support (SCBS)
may not operate under the following conditions:
 


y Refl ection of the laser is poor due to the shape of the vehicle ahead.



y The vehicle ahead is signifi cantly dirty.



y Under bad weather condition, such as rain, fog and snow.



y The window washer is being used or the windshield wipers are not used when it's
raining.
 


y The windshield is dirty.



y The steering wheel is turned completely left or right, or the vehicle is accelerated
rapidly and comes close to the vehicle ahead.
 


y Trucks with low loading platforms and vehicles with an extremely low or high profi le.



y Vehicles with certain shapes such as a vehicle carrier.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










*Some models.4–107
When Driving
i-ACTIVSENSE
 


y Under the following conditions, the Smart City Brake Support (SCBS) system may not
operate normally.
 


y Heavy luggage is loaded in the luggage compartment or on the rear seat.



y If there is the possibility of partial contact with a vehicle ahead.



y When driving on continuously curving roads, and entering and exiting exits.



y Elongated luggage or cargo is loaded onto installed roof rails and covers the laser
sensor (front) .
 


y Exhaust gas from the vehicle in front, sand, snow, and water vapor rising from
manholes and grating, and water splashed into the air.
 


y When towing a malfunctioning vehicle.



y When driving with tires having signifi cantly different wear.




y In the following cases, the laser sensor (front) may inadvertently determine that there is a
vehicle ahead and the Smart City Brake Support (SCBS) system may operate.
 


y Objects on the road at the entrance to a curve.



y Vehicles passing in the opposite lane while making a curve.



y Metal objects, bumps, or protruding objects on the road.



y When passing through a toll gate equipped with a bar.



y When passing under a vinyl curtain or fl ag.



y Plastic objects such as pylons.



y Two-wheeled vehicles, pedestrians, animals or standing trees.




y When the system operates, the user is notifi ed by the fl ashing Smart City Brake Support
(SCBS) indicator light (red) and the active driving display * . 


y The Smart City Brake Support (SCBS) warning light (amber) turns on when the system
has a malfunction.
  Refer to Warning Lights on page 4-25 .
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–10 8
When Driving
i-ACTIVSENSE
Smart City Brake Support (SCBS)
Indicator Light (Red)
If the Smart City Brake Support (SCBS) is
operating, the indicator light (red) fl ashes.
Automatic Brake Operation
Display (Vehicles With Active
Driving Display)
“SCBS Automatic Brake” is displayed in
the active driving display while the SCBS
brakes or the brake assist (SCBS brake
assist) is operating.
NOTE
 


y The collision warning beep sounds
intermittently while the SCBS brake
or brake assist (SCBS brake assist) is
operating.
 


y If the vehicle is stopped by the SCBS
operation and the brake pedal is not
depressed, the warning beep sounds
one time after about 2 seconds and the
SCBS brake is automatically released.
Stopping the Smart City Brake
Support (SCBS) System Operation
The Smart City Brake Support (SCBS)
system can be temporarily deactivated.
When the Smart City Brake Support
(SCBS) system is turned off, the Smart
City Brake Support (SCBS) OFF indicator
light turns on.
When the engine is restarted, the system
becomes operational.
Without SCBS OFF switch
Refer to Personalization Features on page
9-10 .
With SCBS OFF switch
Press the SCBS OFF switch to turn
off the system. The Smart City Brake
Support (SCBS) OFF indicator light in the
instrument cluster will illuminate.
Press the switch again to turn the system
back on. The Smart City Brake Support
(SCBS) OFF indicator light will turn off.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–110
When Driving
i-ACTIVSENSE
NOTE
 


y The Smart Brake Support (SBS) system operates when all of the following conditions are
met:
 


y The ignition is switched ON.



y The Smart Brake Support (SBS) system is on.



y The vehicle speed is about 15 km/h or faster (10 mph or faster).



y The relative speed between your vehicle and the vehicle ahead is about 15 km/h or
faster (10 mph or faster).
 


y The Dynamic Stability Control (DSC) is not operating.




y The Smart Brake Support (SBS) system may not operate under the following conditions:




y If the vehicle is accelerated rapidly and it comes close to a vehicle ahead.



y The vehicle is driven at the same speed as the vehicle ahead.



y The accelerator pedal is depressed.



y The brake pedal is depressed.



y The steering wheel is being operated.



y The selector lever is being operated.



y The turn signal is being used.



y When the vehicle ahead is not equipped with taillights or the taillights are turned off.



y When warnings and messages, such as a dirty windshield, related to the Forward
Sensing Camera (FSC)/laser sensor (front) are being displayed in the center display.
 


y Although the objects which activate the system are four-wheeled vehicles, the radar
sensor (front) could detect the following objects, determine them to be an obstruction, and
operate the Smart Brake Support (SBS) system.
 


y Objects on the road at the entrance to a curve (including guardrails and snow banks).



y A vehicle appears in the opposite lane while cornering or rounding a curve.



y When crossing a narrow bridge.



y When passing under a low gate or through a tunnel or narrow gate.



y When entering an underground parking area.



y Metal objects, bumps, or protruding objects on the road.



y If you suddenly come close to a vehicle ahead.



y When driving in areas where there is high grass or forage.



y Two-wheeled vehicles such as motorbikes or bicycles.



y Pedestrians or non-metallic objects such as standing trees.




y When the system operates, the user is notifi ed by the fl ashing Smart Brake Support (SBS)
indicator light (red) and the active driving display.
 


y The Smart Brake Support (SBS) warning light (amber) turns on when the system has a
malfunction. Refer to Warning/Indicator Lights on page 4-24 .
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–111
When Driving
i-ACTIVSENSE
Smart Brake Support (SBS)
Indicator Light (Red)
If the Smart Brake Support (SBS) is
operating, the indicator light (red) fl ashes.
Collision Warning
If there is the possibility of a collision
with a vehicle ahead, the beep sounds
continuously and a warning is indicated in
the active driving display.
Stopping The Smart Brake
Support (SBS) System Operation
The Smart Brake Support (SBS) system
can be temporarily deactivated.
Refer to Personalization Features on page
9-10 .
When the Smart Brake Support (SBS)
system is turned off, the Smart Brake
Support (SBS) OFF indicator light turns
on.
When the engine is restarted, the system
becomes operational.
NOTE
If the Smart Brake Support (SBS) system
operation is turned off, the Smart City
Brake Support (SCBS) system operation is
turned off simultaneously.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC