2016 MAZDA MODEL 6 warning lights

Black plate (31,1)
Seat Belt Warning Systems
If it detects that the driver's seat belt is
unfastened, the warning light or beep
alerts the driver.
Refer to Warning/Indicator Lights on page
4-22.
Front Seat Belt Pretensioner
and Load Limiting Systems
For optimum protection, the driver and
front passenger seat belts are equipped
with pretensioner and load limiting
systems. For both these systems to work
properly you must wear the seat belt
properly.
Pretensioners:
In moderate or severe frontal or near-
frontal accidents, the front air bag and
pretensioner systems deploy
simultaneously.
For deployment details, refer to the SRS
Air Bag Deployment Criteria (page 2-54).
The front seat belt retractors remove slack
quickly as the air bags are expanding.
Any time the air bags and seat belt
pretensioners have fired they must be
replaced.
A system malfunction or operation
conditions are indicated by a warning.
Refer to Warning/Indicator Lights on page
4-22.
Refer to Air Bag/Front Seat Belt
Pretensioner System Warning Beep on
page 7-34.
(With Front Passenger Occupant
Classification System)
In addition, the pretensioner system for
the front passenger, like the front and side
passenger air bag, is designed to only
deploy when the front passenger occupant
classification sensor detects a passenger
sitting on the front passenger's seat.
For details, refer to the front passenger
occupant classification sensor (page
2-57).
Essential Safety Equipment
Seat Belt Systems
2-19
Mazda6_8EA2-EA-14K_Edition2 Page31
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (65,1)
(With Front Passenger Occupant Classification System)
In a roll-over:
In response to a vehicle roll-over, both curtain air bags inflate.
Both curtain air bags will deploy after
the roll-over accident is detected.
qWarning Light/Beep
A system malfunction or operation conditions are indicated by a warning.
Refer to Warning/Indicator Lights on page 4-22.
Refer to Air Bag/Front Seat Belt Pretensioner System Warning Beep on page 7-34.
Essential Safety Equipment
SRS Air Bags
2-53
Mazda6_8EA2-EA-14K_Edition2 Page65
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (78,1)
Keyless Entry System
This system uses the key buttons to
remotely lock and unlock the doors, and
opens the trunk lid.
The system can start the engine without
having to take the key out of your purse
or pocket.
It can also help you signal for attention.
Operating the theft-deterrent system is
also possible on theft-deterrent system-
equipped vehicles.
Press the buttons slowly and carefully.
System malfunctions or warnings are
indicated by the following warning lights
or beeps.
For vehicles with the type A instrument
cluster, check the displayed message for
more information and, if necessary, have
the vehicle inspected at an Authorized
Mazda Dealer, according to the indication.
lKEY Warning Light (Red)
Refer to Warning/Indicator Lights on
page 4-22.
lIgnition Not Switched Off (STOP)
Warning Beep
Refer to Ignition Not Switched Off
(STOP) Warning Beep on page 7-35.
lKey Removed from Vehicle Warning
Beep
Refer to Key Removed from Vehicle
Warning Beep on page 7-35.
If you have a problem with the key,
consult an Authorized Mazda Dealer.
If your key is lost or stolen, consult an
Authorized Mazda Dealer as soon as
possible for a replacement and to make
the lost or stolen key inoperative.
CAUTION
Radio equipment like this is governed
by laws.
Changes or modifications not
expressly approved by the party
responsible for compliance could void
the user's authority to operate the
equipment.
NOTE
lThe keyless entry system operation may
vary due to local conditions.
lThe keyless entry system is fully operational
(door lock/unlock) when the push button
start is switched off. The system does not
operate if the push button start is switched
to any position other than off.
lIf the key does not operate when pressing a
button or the operational range becomes
too small, the battery may be dead. To
install a new battery, refer to Replace
Electrical Battery(page 6-38).
lBattery life is about one year. Replace the
battery with a new one if the KEY indicator
light (green) flashes in the instrument
cluster. Replacing the battery about once a
year is recommended because the KEY
warning light/indicator light may not
illuminate or flash depending on the rate of
battery depletion.
lAdditional keys can be obtained at an
Authorized Mazda Dealer. Up to 6 keys can
be used with the keyless functions per
vehicle. Bring all keys to an Authorized
Mazda Dealer when additional keys are
required.
3-4
Before Driving
Keys
Mazda6_8EA2-EA-14K_Edition2 Page78
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (79,1)
qTransmitter
Operation buttons Operation indicator light
NOTEl(With theft-deterrent system)
The hazard warning lights flash when the
theft-deterrent system is armed or turned
off.
Refer to Theft-Deterrent System on page
3-41.
l(With the advanced keyless function)
A beep sound can be heard for confirmation
when the doors are locked/unlocked using
the key. If you prefer, the beep sound can be
turned off.
The volume of the beep sound can also be
changed.
Refer to Personalization Features on page
9-9.
Use the following procedure to change the
setting.
1. Switch the ignition off and close all of the
doors and the trunk lid.
2. Open the driver's door.3. Within 30 seconds of opening the driver's
door, press and hold the LOCK button on
the key for 5 seconds or longer.
All of the doors lock and the beep sound
activates at the currently set volume. (If the
beep sound is currently set to not activate, it
will not activate.) The setting changes each
time the LOCK button on the key is pressed
and the beep sound activates at the set
volume. (If the beep sound has been set to
not activate, it will not activate.)
4. The setting change is completed by doing
any one of the following:
lSwitch the ignition to ACC or ON.lClose the driver's door.lOpen the trunk lid.lThe key is not operated for 10 seconds.lPress any button except the LOCK
button on the key.
lA request switch is pressed.
The operation indicator light flashes when
the buttons are pressed.
Lock button
To lock the doors, press the lock button
and the hazard warning lights will flash
once.
(With the advanced keyless function)
A beep sound will be heard once.
To confirm that all doors have been
locked, press the lock button again within
5 seconds. If they are closed and locked,
the horn will sound.
Before Driving
Keys
3-5
Mazda6_8EA2-EA-14K_Edition2 Page79
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (80,1)
NOTElThe doors can be locked by pressing the
lock button while any other door or the
trunk lid is open. The hazard warning lights
will not flash.
When the lock button is pressed while any
door is open and then the door is closed, all
the doors are locked.
lConfirm that all doors are locked visually
or audibly by use of the double click.
lMake sure all doors are locked after
pressing the button.
l(With theft-deterrent system)
When the doors are locked by pressing the
lock button on the key while the theft-
deterrent system is armed, the hazard
warning lights will flash once to indicate
that the system is armed.
Unlock button
To unlock the driver's door, press the
unlock button and the hazard warning
lights will flash twice.
(With the advanced keyless function)
A beep sound will be heard twice.
To unlock all doors, press the unlock
button again within 3 seconds and two
more beep sounds will be heard.
NOTElThe system can be set to unlock all doors by
performing a single operation.
Refer to Personalization Features on page
9-9.
Use the following procedure to change the
setting.
1. Switch the ignition off and close all of the
doors and the trunk lid.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's
door, press and hold the UNLOCK button
on the key for 5 seconds or longer. The
sound of the doors locking/unlocking can
be heard.
After this, the system switches the setting
each time the UNLOCK button is pressed
(the sound of the doors locking/unlocking
can be heard).
4. The setting change is completed by doing
any one of the following:
lSwitch the ignition to ACC or ON.lClose the driver's door.lOpen the trunk lid.lThe key is not operated for 10 seconds.lPress any button except the UNLOCK
button on the key.
lA request switch is pressed.l(Auto re-lock function)
After unlocking with the key, all doors will
automatically lock if any of the following
operations are not performed within about
60 seconds. If your vehicle has a theft-
deterrent system, the hazard warning lights
will flash for confirmation.
The time required for the doors to lock
automatically can be changed.
Refer to Personalization Features on page
9-9.
lA door or the trunk lid is opened.lThe push button start is switched to any
position other than off.
3-6
Before Driving
Keys
Mazda6_8EA2-EA-14K_Edition2 Page80
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (81,1)
l(With theft-deterrent system)
When the doors are unlocked by pressing
the unlock button on the key while the theft-
deterrent system is turned off, the hazard
warning lights will flash twice to indicate
that the system is turned off.
Trunk button
To open the trunk lid, press and hold the
trunk button until the trunk lid opens.
Panic button
If you witness from a distance someone
attempting to break into or damage your
vehicle, press and hold the panic button to
activate the vehicle's alarm.
NOTE
The panic button will work whether any door
or the trunk lid is open or closed.
(Turning on the alarm)
Pressing the panic button for 1 second or
more will trigger the alarm for about 2
minutes and 30 seconds, and the
following will occur:
lThe horn sounds intermittently.lThe hazard warning lights flash.(Turning off the alarm)
The alarm stops by pressing any button on
the key.
qOperational Range
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
Starting the Engine
NOTE
lStarting the engine may be possible even if
the key is outside of the vehicle and
extremely close to a door and window,
however, always start the engine from the
driver's seat.
If the vehicle is started and the key is not in
the vehicle, the vehicle will not restart after
it is shut off and the push button start is
switched to off.
lThe trunk is out of the assured operational
range, however, if the key (transmitter) is
operable the engine will start.
With the advanced keyless function
Interior antenna
Operational range
Before Driving
Keys
3-7
Mazda6_8EA2-EA-14K_Edition2 Page81
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (87,1)
qLocking, Unlocking with Request
Switch (With the advanced
keyless function)
All doors can be locked/unlocked by
pressing the request switch on the front
doors while the key is being carried.
Front doors
Request switch
To lock
To lock the doors, press the request switch
and the hazard warning lights will flash
once.
A beep sound will be heard once.
To unlock
Driver's door request switch
To unlock the driver's door, press the
request switch. A beep sound will be
heard twice and the hazard warning lights
will flash twice.
To unlock all doors, press the request
switch again within 3 seconds and two
more beep sounds will be heard.
Front passenger door request switch
To unlock all doors, press the request
switch. A beep sound will be heard twice
and the hazard warning lights will flash
twice.NOTE
lThe system can be set to unlock all doors by
performing a single operation.
Refer to Personalization Features on page
9-9.
Use the following procedure to change the
setting.
1. Switch the ignition off and close all of the
doors and the trunk lid.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's
door, press and hold the UNLOCK button
on the key for 5 seconds or longer. The
sound of the doors locking/unlocking can
be heard.
After this, the system switches the setting
each time the UNLOCK button is pressed
(the sound of the doors locking/unlocking
can be heard).
4. The setting change is completed by doing
any one of the following:
lSwitch the ignition to ACC or ON.lClose the driver's door.lOpen the trunk lid.lThe key is not operated for 10 seconds.lPress any button except the UNLOCK
button on the key.
lA request switch is pressed.lConfirm that all doors and the trunk lid are
securely locked.
For the trunk lid, move it without pressing
the electric trunk lid opener to verify that
the trunk lid has not been left ajar.
lAll doors cannot be locked when any door
is open.
lIt may require a few seconds for the doors
to unlock after the request switch is
pressed.
Before Driving
Doors and Locks
3-13
Mazda6_8EA2-EA-14K_Edition2 Page87
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (88,1)
lA beep sound is heard for confirmation
when the doors are locked/unlocked using
the request switch. If you prefer, the beep
sound can be turned off.
The volume of the beep sound can also be
changed.
Refer to Personalization Features on page
9-9.
Use the following procedure to change the
setting.
1. Switch the ignition off and close all of the
doors and the trunk lid.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's
door, press and hold the LOCK button on
the key for 5 seconds or longer.
All of the doors lock and the beep sound
activates at the currently set volume. (If the
beep sound is currently set to not activate, it
will not activate.) The setting changes each
time the LOCK button on the key is pressed
and the beep sound activates at the set
volume. (If the beep sound has been set to
not activate, it will not activate.)
4. The setting change is completed by doing
any one of the following:
lSwitch the ignition to ACC or ON.lClose the driver's door.lOpen the trunk lid.lThe key is not operated for 10 seconds.lPress any button except the LOCK
button on the key.
lA request switch is pressed.l(With theft-deterrent system)
The hazard warning lights flash when the
theft-deterrent system is armed or turned
off.
Refer to Theft-Deterrent System on page
3-41.
lThe setting can be changed so that the
doors are locked automatically without
pressing the request switch.
Refer to Personalization Features on page
9-9.
(Auto-lock function)
A beep sound is heard when all doors are
closed while the advanced key is being
carried. All doors are locked automatically
after about three seconds when the
advanced key is out of the operational
range. Also, the hazard warning lights flash
once. (Even if the driver is in the
operational range, all doors are locked
automatically after about 30 seconds.) If
you are out of the operational range before
the doors and the trunk lid are completely
closed or another key is left in the vehicle,
the auto-lock function will not work.
Always make sure that all doors and the
trunk lid are closed and locked before
leaving the vehicle. The auto-lock function
does not close the power windows.
l(Auto re-lock function)
After unlocking with the request switch, all
doors will automatically lock if any of the
following operations are not performed
within about 60 seconds. If your vehicle has
a theft-deterrent system, the hazard
warning lights will flash for confirmation.
The time required for the doors to lock
automatically can be changed.
Refer to Personalization Features on page
9-9.
lA door or the trunk lid is opened.lThe ignition is switched to any position
other than off.
3-14
Before Driving
Doors and Locks
Mazda6_8EA2-EA-14K_Edition2 Page88
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K