2016 MAZDA MODEL 6 windshield wipers

Black plate (254,1)
NOTElThe Smart City Brake Support (SCBS) system will not operate if the driver is deliberately
performing driving operations (accelerator pedal and steering wheel).
lThe Smart City Brake Support (SCBS) system will operate under the following conditions.lThe engine is running.l“SCBS Forward malfunction”is not displayed in the multi-information display.lThe vehicle speed is between about 4 to 30 km/h (2 to 18 mph).lThe Smart City Brake Support (SCBS) system is not turned off.lThe DSC is not malfunctioning.lThe Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-infrared laser
beam and receiving the beam reflected off the reflector of the vehicle ahead, and then using it for
the measurement. Consequently, the Smart City Brake Support (SCBS) may not operate under the
following conditions:
lReflection of the laser is poor due to the shape of the vehicle ahead.lThe vehicle ahead is significantly dirty.lUnder bad weather condition, such as rain, fog and snow.lThe window washer is being used or the windshield wipers are not used when it's raining.lThe windshield is dirty.lThe steering wheel is turned completely left or right, or the vehicle is accelerated rapidly and
comes close to the vehicle ahead.
lTrucks with low loading platforms and vehicles with an extremely low or high profile.lVehicles with certain shapes such as a vehicle carrier.lUnder the following conditions, the Smart City Brake Support (SCBS) system may not operate
normally.
lHeavy luggage is loaded in the luggage compartment or on the rear seat.lIf there is the possibility of partial contact with a vehicle ahead.lWhen driving on continuously curving roads, and entering and exiting exits.lElongated luggage or cargo is loaded onto installed roof rails and covers the laser sensor.lExhaust gas from the vehicle in front, sand, snow, and water vapor rising from manholes and
grating, and water splashed into the air.
lWhen towing a malfunctioning vehicle.lWhen driving with tires having significantly different wear.lIn the following cases, the laser sensor may inadvertently determine that there is a vehicle ahead
and the Smart City Brake Support (SCBS) system may operate.
lObjects on the road at the entrance to a curve.lVehicles passing in the opposite lane while making a curve.lMetal objects, bumps, or protruding objects on the road.lWhen passing through a toll gate equipped with a bar.lWhen passing under a vinyl curtain or flag.lPlastic objects such as pylons.lTwo-wheeled vehicles, pedestrians, animals or standing trees.lWhen the system operates, the user is notified by the flashing Smart City Brake Support (SCBS)
warning indication and the multi-information display.
4-130
When Driving
i-ACTIVSENSE
Mazda6_8EA2-EA-14K_Edition2 Page254
Saturday, January 10 2015 3:25 PM
Form No.8EA2-EA-14K

Black plate (265,1)
Laser Sensor (Front)í
Your vehicle is equipped with a laser sensor (front). The laser sensor (front) is positioned
near the rearview mirror and used by the following systems.
lSmart Brake Support (SBS)lSmart City Brake Support (SCBS)
CAUTION
Heed the following precautions to assure correct operation of the system.
ØKeep the windshield clean at all times.
ØDo not apply stickers to the surface of the windshield (including transparent
stickers).
ØIf cracks or damage caused by flying gravel or debris is visible near the laser
sensor (front), stop using the system immediately and have your vehicle inspected
by an Authorized Mazda Dealer.
See the next page on how to turn off the system. Refer to Personalization Features
on page 9-9.
ØDo not apply a coating agent to the windshield.
ØWhen replacing the windshield wipers or windshield, consult an Authorized
Mazda Dealer.
ØNever remove the sensor.
ØA removed sensor will not meet the conditions for a class 1M laser under the IEC
60825-1 specification and therefore eye safety cannot be assured.
ØDo not peer into the sensor using optical instruments with a magnification
function such as magnifying glasses, and microscopic and objective lenses within
a distance of 100 mm (3.94 in) from the sensor.
When Driving
i-ACTIVSENSE
4-141íSome models. Mazda6_8EA2-EA-14K_Edition2 Page265
Saturday, January 10 2015 3:25 PM
Form No.8EA2-EA-14K

Black plate (453,1)
Wiper Blades
CAUTION
ØHot waxes applied by automatic
car washers have been known to
affect the wiper's ability to clean
windows.
ØTo prevent damage to the wiper
blades, do not use gasoline,
kerosene, paint thinner, or other
solvents on or near them.
ØWhen the wiper lever is in the
AUTO position and the ignition is
switched ON, the wipers may
move automatically in the
following cases:
ØIf the windshield above the rain
sensor is touched.
ØIf the windshield above the rain
sensor is wiped with a cloth.
ØIf the windshield is struck with
a hand or other object.
ØIf the rain sensor is struck with
a hand or other object from
inside the vehicle.
Be careful not to pinch hands or
fingers as it may cause injury, or
damage the wipers. When
washing or servicing your Mazda,
make sure the wiper lever is in the
OFF position.
Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.
qReplacing Windshield Wiper Blades
When the wipers no longer clean well, the
blades are probably worn or cracked.
Replace them.
CAUTION
To prevent damage to the wiper arms
and other components, do not try to
sweep the wiper arm by hand.
NOTE
To prevent damage to the wiper arm blades
when raising both the driver and passenger
side wiper arms, raise the driver side wiper
arm first. Conversely, when setting down the
wiper arms, set the passenger side wiper arm
down first.
1. Raise the wiper arm.
2. Open the clip and slide the blade
assembly in the direction of the arrow.
Maintenance and Care
Owner Maintenance
6-33
Mazda6_8EA2-EA-14K_Edition2 Page453
Saturday, January 10 2015 3:27 PM
Form No.8EA2-EA-14K

Black plate (483,1)
Prevention
It is necessary to wash and wax your
vehicle to preserve its finish according to
the instructions in this section. These
steps should be taken immediately after
you find water marks on your vehicle's
finish.
Paint Chipping
Occurrence
Paint chipping occurs when gravel thrown
in the air by another vehicle's tires hits
your vehicle.
How to avoid paint chipping
Keeping a safe distance between you and
the vehicle ahead reduces the chances of
having your paint chipped by flying
gravel.
NOTE
lThe paint chipping zone varies with the
speed of the vehicle. For example, when
traveling at 90 km/h (56 mph), the paint
chipping zone is 50 m (164 ft).
lIn low temperatures a vehicle's finish
hardens. This increases the chance of paint
chipping.
lChipped paint can lead to rust forming on
your Mazda. Before this happens, repair the
damage by using Mazda touch-up paint
according to the instructions in this section.
Failure to repair the affected area could
lead to serious rusting and expensive
repairs.
Followalllabel and container directions
when using a chemical cleaner or polish.
Read all warnings and cautions.
qMaintaining the Finish
Washing
CAUTION
ØWhen the wiper lever is in the
AUTO position and the ignition is
switched ON, the wipers may
move automatically in the
following cases:
ØIf the windshield above the rain
sensor is touched or wiped with
a cloth.
ØIf the windshield is struck with
a hand or other object from
either outside or inside the
vehicle.
Keep hands and scrapers clear of
the windshield when the wiper
lever is in the AUTO position and
the ignition is switched ON as
fingers could be pinched or the
wipers and wiper blades damaged
when the wipers activate
automatically.
If you are going to clean the
windshield, be sure the wipers are
turned off completely―this is
particularly important when
clearing ice and snow―when it is
most likely that the engine is left
running.
ØDo not spray water in the engine
compartment. Otherwise, it could
result in engine-starting problems
or damage to electrical parts.
ØWhen washing and waxing the
vehicle, be careful not to apply
excessive force to any single area
of the vehicle roof or the antenna.
Otherwise, you could dent the
vehicle or damage the antenna.
Maintenance and Care
Appearance Care
6-63
Mazda6_8EA2-EA-14K_Edition2 Page483
Saturday, January 10 2015 3:27 PM
Form No.8EA2-EA-14K

Black plate (600,1)
Item FeatureFactory
SettingAvailable
SettingsSettings change method
VehicleIllumination
entry
Refer to
Illuminated
Entry
System on
page 5-129.The time required for the
interior lamp to turn off
automatically can be changed
(prevents battery depletion
when a door is open/ajar).30
minutes60
minutes/
30
minutes/
10
minutes
Refer to
Settings
on page
5-49.―
The time required for the
interior lamp to turn off
automatically after all doors are
closed can be changed.15
seconds60
seconds/
30
seconds/
15
seconds/
7.5
secondsRefer to
Settings
on page
5-49.―
Auto-wiper
control
Refer to
Windshield
Wipers and
Washer on
page 4-64.The auto-wiper control function
can be changed.On On/Off
*4Refer to
Settings
on page
5-49.―
Daytime
running
lights
Refer to
Daytime
Running
Lights on
page 4-62.The function of the daytime
running lights can be changed.OnOn/
Off――
Auto
headlight off
Refer to
Headlights
on page
4-58.The time required for headlights
to turn off after ignition is
switched off can be changed.30
seconds120
seconds/
90
seconds/
60
seconds/
30
seconds/
Off
*5
Refer to
Settings
on page
5-49.―
Auto-light
control
Refer to
Headlights
on page
4-58.The headlight illumination
on/off sensitivity based on
surrounding lightness/darkness
can be changed.MediumHigh/
Med.
High/
Medium/
Med.
Low/
Low
Refer to
Settings
on page
5-49.―
9-14
Personalization Features
Mazda6_8EA2-EA-14K_Edition2 Page600
Saturday, January 10 2015 3:27 PM
Form No.8EA2-EA-14K

Black plate (613,1)
V
Vanity Mirrors ................................. 5-127
Vehicle Information Labels ................. 9-2
W
Warning Lights
ABS ............................................ 4-30
Air bag/front seat belt pretensioner
system ........................................ 4-35
Automatic transaxle ................... 4-34
Brake system .............................. 4-29
Charging system ......................... 4-31
Check engine .............................. 4-32
Check fuel cap ........................... 4-35
Door-ajar .................................... 4-37
Electric parking brake ................ 4-31
Engine oil ................................... 4-31
HBC ........................................... 4-41
High engine coolant
temperature ................................ 4-32
KEY ............................................ 4-39
LDWS ........................................ 4-33
LED headlight ............................ 4-46
Low fuel ..................................... 4-35
Low washer fluid level ............... 4-37
Mazda Radar Cruise Control
(MRCC) ..................................... 4-45
Seat belt ...................................... 4-36
Tire pressure monitoring
system ........................................ 4-38
Warning/Buzzer ................................ 7-23
Warranty ............................................ 8-16
Weights ............................................... 9-5
Windows
Power windows .......................... 3-33
Windshield Washer ........................... 4-68
Windshield Wipers ............................ 4-65
Winter Driving .................................. 3-45
W
Wiper
Replacing Windshield Wiper
Blades ........................................ 6-33
Index
10-9
Mazda6_8EA2-EA-14K_Edition2 Page613
Saturday, January 10 2015 3:28 PM
Form No.8EA2-EA-14K