2016 MAZDA MODEL 6 bulb

Black plate (471,1)
Front turn signal lights/Front side-
marker lights
Parking lights (With halogen
headlights)
7. Install the new bulb in the reverse order
of the removal procedure.
Fog lights (With LED headlights)í
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Brake lights, Taillights, High-mount
brake light, Side-turn signal lights,
Rear side-marker lights (With LED
headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Rear turn signal lights, Rear side-
marker lights (With halogen
headlights)
1. Make sure the ignition is switched off,
and the turn signal switch is off.
2. Lift the trunk mat.
3.(Left side)
Pull the center of each plastic retainer
and remove the retainers and the
pocket.
(Right side)
Remove the pocket.
(Left side)
Removal
Installation
Maintenance and Care
Owner Maintenance
6-51íSome models. Mazda6_8EA2-EA-14K_Edition2 Page471
Saturday, January 10 2015 3:27 PM
Form No.8EA2-EA-14K

Black plate (472,1)
(Right side)
4. Pull the center of each plastic retainer
and remove the retainers and the trunk
end trim.
Removal
Installation
5. Pull the center of each plastic retainer
and remove the retainers and the trunk
side trim.
6. Turn the socket and bulb assembly
counterclockwise and remove it.
7. Disconnect the bulb from the socket.
Rear turn signal lights
Rear side-marker lights
8. Install the new bulb in the reverse order
of the removal procedure.
Taillights (Trunk lid side) (With LED
headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
6-52
Maintenance and Care
Owner Maintenance
Mazda6_8EA2-EA-14K_Edition2 Page472
Saturday, January 10 2015 3:27 PM
Form No.8EA2-EA-14K

Black plate (473,1)
Taillights (Trunk lid side) (With
halogen headlights), Reverse lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the center of each plastic retainer
and remove the retainers and the trunk
lid trim.
Removal
Installation
3.(Reverse lights)
Disconnect the electrical connector
from the bulb by pressing the tab on
the connector with your finger and
pulling the connector.
4. Turn the socket and bulb assembly
counterclockwise and remove it.
5. Disconnect the bulb from the socket.Taillights (Trunk lid side)
Reverse lights
6. Install the new bulb in the reverse order
of the removal procedure.
License plate lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the lens,
and then remove the lens by carefully
prying on the edge of the lens with a
flathead screwdriver.
Maintenance and Care
Owner Maintenance
6-53
Mazda6_8EA2-EA-14K_Edition2 Page473
Saturday, January 10 2015 3:27 PM
Form No.8EA2-EA-14K

Black plate (474,1)
3. Disconnect the bulb by pulling it out.
4. Install the new bulb in the reverse order
of the removal procedure.
qReplacing Interior Light Bulbs
Overhead lights/Front map lights (LED
type), Rear map lights (LED type)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Overhead lights/Front map lights (Bulb
type), Rear map lights (Bulb type),
Vanity mirror lightsí, Courtesy lights
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens, and then remove the lens by
carefully prying on the edge of the lens
with the flathead screwdriver.
2. Disconnect the bulb by pulling it out.Overhead lights/Front map lights
Rear map lights
6-54
Maintenance and Care
íSome models.
Owner Maintenance
Mazda6_8EA2-EA-14K_Edition2 Page474
Saturday, January 10 2015 3:27 PM
Form No.8EA2-EA-14K

Black plate (475,1)
Vanity mirror lightsí
Courtesy lights
3. Install the new bulb in the reverse order
of the removal procedure.
Trunk light
1. Press both sides of the lens cap to
remove it.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of the removal procedure.
Maintenance and Care
Owner Maintenance
6-55íSome models. Mazda6_8EA2-EA-14K_Edition2 Page475
Saturday, January 10 2015 3:27 PM
Form No.8EA2-EA-14K

Black plate (522,1)
qIf the turn signal/hazard warning
indicator light illuminates or flashes
at an abnormally high speed
If an indicator light flashes abnormally,
one of the turn signal bulbs may be
burned out. Consult an Authorized Mazda
Dealer.
qIf the security indicator light
illuminates or flashes
If the engine does not start with the
correct key, and the security indicator
light keeps illuminating or flashing, the
system may have a malfunction. Consult
an Authorized Mazda Dealer.
qIf the Mazda Radar Cruise
Control (MRCC) Warning Light
(Amber) illuminates
í
The warning light turns on if there is a
malfunction in the system while the
Mazda Radar Cruise Control (MRCC)
system is on. Have your vehicle inspected
at an Authorized Mazda Dealer.
qIf the blind spot monitoring
(BSM) system OFF indication/
indicator light illuminates
í
Type A
If the indication remains displayed even
though the Blind Spot Monitoring (BSM)
switch has been operated, it indicates a
problem in the system. Have your vehicle
inspected at an Authorized Mazda Dealer.
Type B
A problem in the system may be indicated
under the following conditions. Have your
vehicle inspected at an Authorized Mazda
Dealer.
lThe light does not turn on when the
ignition is switched ON.
7-32
If Trouble Arises
íSome models.
Warning/Indicator Lights and Warning Sounds
Mazda6_8EA2-EA-14K_Edition2 Page522
Saturday, January 10 2015 3:27 PM
Form No.8EA2-EA-14K

Black plate (592,1)
qAir Conditioner
The type of refrigerant used is indicated on a label attached to the inside of the engine compartment. Check the
label before recharging the refrigerant. Refer to Climate Control System on page 5-2.
Item Classification
Refrigerant Type HFC134a (R-134a)
qLight Bulbs
Exterior light
Light bulbCategory
Wattage UNECE
*1(SAE)
HeadlightsHalogenHigh beam 60 HB3 (9005)
Low beam 55 H11 (H11)
LEDHigh beam LED
*2―(―)
Low beam LED*2―(―)
Daytime running lightsWith halogen bulb
headlights60 HB3 (9005)
With LED headlights LED
*2―(―)
Front turn signal lights/Parking
lights (Front side-marker lights)With halogen bulb
headlights27/8―(#7444NA)
Front turn signal lights/Front
side-marker lightsWith LED headlights 27/8―(#7444NA)
Fog lights
íLED*2―(―)
Signature wing illumination LED*2―(―)
Side turn signal lights LED*2―(―)
High-mount brake light LED*2―(―)
Rear turn signal lights 21 WY21W (7443NA)
Rear side-marker lightsWith halogen bulb
headlights5 W5W (―)
With LED headlights LED
*2―(―)
Brake lights/Taillights LED*2―(―)
TaillightsWith halogen bulb
headlights5 W5W (―)
With LED headlights LED
*2―(―)
Reverse lights 21 W21W (7440)
License plate lights 5 W5W (―)
*1 UNECE stands for United Nations Economic Commission for Europe.
*2 LED is the abbreviation for Light Emitting Diode.
9-6íSome models.
Specifications
Mazda6_8EA2-EA-14K_Edition2 Page592
Saturday, January 10 2015 3:27 PM
Form No.8EA2-EA-14K

Black plate (593,1)
Interior light
Light bulbCategory
Wattage UNECE
*1
Trunk light 3―
Overhead light (Front)/Map lightsBulb type 8―
LED type LED
*2―
Rear map lightsBulb type 8―
LED type LED
*2―
Courtesy lights 5―
Vanity mirror lights
í2―
*1 UNECE stands for United Nations Economic Commission for Europe.
*2 LED is the abbreviation for Light Emitting Diode.
qTires
NOTE
The tires have been optimally matched with the chassis of your vehicle.
When replacing tires, Mazda recommends that you replace tires of the same type originally fitted to
your vehicle. For details, contact an Authorized Mazda Dealer.
Check the tire pressure label for tire size and inflation pressure.
Refer to Tire Inflation Pressure on page 6-41.
After adjusting the tire pressure, initialization of the tire pressure monitoring system is
necessary to make the system operates normally.
Refer to Tire Pressure Monitoring System Initialization on page 4-151.
Standard tire
(U.S.A. and Canada)
Tire sizeInflation pressure
Front Rear
P225/55R17 95V 250 kPa (36 psi) 250 kPa (36 psi)
P225/45R19 92W 240 kPa (35 psi) 240 kPa (35 psi)
(Mexico)
Tire sizeInflation pressure
Up to 3 persons―Full load
225/55R17 97VFront 230 kPa (2.3 bar, 33 psi) 250 kPa (2.5 bar, 36 psi)
Rear 230 kPa (2.3 bar, 33 psi) 320 kPa (3.2 bar, 46 psi)
225/45R19 92WFront 230 kPa (2.3 bar, 33 psi) 250 kPa (2.5 bar, 36 psi)
Rear 230 kPa (2.3 bar, 33 psi) 320 kPa (3.2 bar, 46 psi)
1 person's weight: About 75 kg
Specifications
9-7íSome models. Mazda6_8EA2-EA-14K_Edition2 Page593
Saturday, January 10 2015 3:27 PM
Form No.8EA2-EA-14K