2016 LINCOLN MKS homelink

HomeLink Wireless Control System
WARNINGS
Make sure that the garage door and
security device are free from
obstruction when you are
programming. Do not program the system
with the vehicle in the garage. Do not use the system with any garage
door opener that does not have the
safety stop and reverse feature as
required by U.S. Federal Safety Standards
(this includes any garage door opener
manufactured before April 1, 1982). A garage
door opener which cannot detect an object,
signaling the door to stop and reverse, does
not meet current federal safety standards.
Using a garage door opener without these
features increases the risk of serious injury or
death. Note:
Make sure you keep the original remote
control transmitter for use in other vehicles as
well as for future system programming.
Note: We recommend that upon the sale or
lease termination of your vehicle, you erase
the programmed function buttons for security
reasons. See Erasing the Function Button
Codes. Note:
You can program a maximum of three
devices. To change or replace any of the three
devices after it has been initially programmed,
you must first erase the current settings. See
Erasing the Function Button Codes
. The universal garage door opener replaces
the common hand-held garage door opener
with a three-button transmitter that is
integrated into the driver
’s sun visor.
The system includes two primary features, a
garage door opener and a platform for
remote activation of devices within the home.
As well as being programmed for garage
doors, the system transmitter can be
programmed to operate entry gate operators,
security systems, entry door locks and home
or office lighting. Additional system information can be found
online at www.homelink.com,
www.youtube.com/HomeLinkGentex or by
calling the toll-free help line on
1-800-355-3515.
In-Vehicle Programming
This process is to program your hand-held
transmitter and your in-vehicle HomeLink
button.
Note:
The programming steps below assume
you will be programming HomeLink that was
not previously programmed.
Note: Put a new battery in the hand-held
transmitter. This will ensure quicker training
and accurate transmission of the
radio-frequency signal. 1. With your vehicle parked outside of the
garage, turn your ignition to the
on
position, but do not start your vehicle.
119
MKS (CLE) Canada/United States of America, enUSA, First Printing Universal Garage Door OpenerE142657 E142658

2. Hold your hand-held garage door
transmitter 2–6 in (5– 14 cm) away from
the HomeLink button you want to
program.
3. Using both hands, simultaneously, press and hold the desired HomeLink button
and the hand-held transmitter button.
DO NOT release either one until the
HomeLink indicator light flashes slowly
and then rapidly. When the indicator light
flashes rapidly, both buttons may be
released. The rapid flashing indicates
successful training.
Note: You may need to use a different method
if you live in Canada or have difficulties
programming your gate operator or garage
door opener. See
Gate Operator / Canadian
Programming.
4. Press and hold the HomeLink button you
programmed for two seconds, then
release. You may need to do this twice to
activate the door. If your garage door
does not operate, watch the HomeLink
indicator light.
If the indicator light stays on, the
programming is complete. No further
action is needed. If the indicator light flashes rapidly for 2
seconds and then turns to a constant light,
the HomeLink button is not programmed yet.
See
Programming Your Garage Door
Opener Motor.
To program additional buttons, repeat Steps
1 – 4.
For questions or comments, please contact
HomeLink at www.homelink.com,
www.youtube.com/HomeLinkGentex or
1-800-355-3515.
Programming Your Garage Door Opener
Motor
Note: You may need a ladder to reach the unit
and you may need to remove the cover or lamp
lens on your garage door opener. 1.
Press the learn button on the garage door
opener motor and then you have 30
seconds to complete the next two steps. 2. Return to your vehicle.
3. Press and hold the function button you
want to program for 2 seconds, then
release. Repeat this step. Depending on
your brand of garage door opener, you
may need to repeat this sequence a third
time.
Gate Operator / Canadian Programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission – which
may not be long enough for HomeLink to pick
up the signal during programming. Similar to
this Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
Note: If programming a garage door opener
or gate operator, it is advised to unplug the
device during the “cycling” process to prevent
possible overheating.
120
MKS (CLE) Canada/United States of America, enUSA, First Printing Universal Garage Door OpenerE142659 E142658

1. Press and hold the HomeLink button
while you press and release, every two
seconds, your hand-held transmitter
until the HomeLink indicator light
changes from a slow to a rapidly blinking
light.
2. Release both the HomeLink and hand-held transmitter buttons.
3. Continue programing HomeLink. See In-Vehicle Programming
.
Erasing the Function Button Codes
Note: You cannot erase individual buttons. 1. Press and hold the outer two function
buttons simultaneously for approximately
20 seconds until the indicator lights
above the buttons flash rapidly. 2. When the indicator lights flash, release
the buttons. The codes for all buttons are
erased.
Reprogramming a Single Button
To program a device to a previously trained
button, follow these steps:
1. Press and hold the desired button. Do NOT release the button.
2. The indicator light will begin to flash after
20 seconds. Without releasing the button,
follow Step 1 in the Programming section.
For questions or comments, contact
HomeLink at www.homelink.com,
www.youtube.com/HomeLinkGentex or
1-800-355-3515.
Programming to a Genie Intellicode 2
Garage Door Opener
Note: The Genie Intellicode 2 transmitter must
already be programmed to operate with the
garage door opener.
Note: To program HomeLink to the
transmitter you must first put the transmitter
into programming mode. Red indicator light
A.
Green indicator light
B.
1. Press and hold one of the buttons on the
hand-held transmitter for 10 seconds. The
indicator light will change from green to
red and green.
2. Press the same button twice to confirm the change to programming mode. If
done properly the indicator light will
appear red.
3. Hold the transmitter within 1– 3 inches
(2 –8 centimeters) of the button on the
visor you want to program.
121
MKS (CLE) Canada/United States of America, enUSA, First Printing Universal Garage Door OpenerE142660 BAE142661

4. Press and hold both the programmed
Genie button on the hand-held
transmitter and the button you want to
program. The indicator light on the visor
will flash rapidly when the programming
is successful.
Note: The Genie transmitter will transmit for
up to 30 seconds. If HomeLink does not
program within 30 seconds the Genie
transmitter will need to be pressed again. If
the Genie transmitter indicator light displays
green and red, release the button until the
indicator light turns off before pressing the
button again.
Once HomeLink has been programmed
successfully, the Genie transmitter must be
changed out of program mode. To do this:
1. Press and hold the previously programmed Genie button on the
hand-held transmitter for 10 seconds. The
indicator light will change from red to red
and green.
2. Press the same button twice to confirm the change. If done correctly the indicator
light will turn green.
Programming HomeLink to the Genie
Intellicode Garage Door Opener Motor
Note: You may need a ladder to access the
garage door opener motor. 1. Press and hold the program button on
the garage door opener motor until both
blue indicator lights turn on.
2. Release the program button. Only the smaller round indicator light should be
on.
3. Press and release the program button. The larger purple indicator light will flash.
Note: The next two steps must be completed
in 30 seconds.
4. Press and release the Genie Intellicode 2 hand-held transmitter ’s previously
programmed button. Both indicator lights
on the garage door opener motor unit
should now flash purple. 5. Press and hold the previously
programmed button on the visor for 2
seconds. Repeat this step up to 3 times
until the garage door moves.
Programming is now complete.
Clearing a HomeLink Device
To erase programming from the three
HomeLink buttons press and hold the two
outer HomeLink buttons until the indicator
light begins to flash. The indicator light will
begin flashing in 10 to 20 seconds, at which
time both buttons should be released.
Programming has now been erased, and the
indicator light should blink slowly to indicate
the device is in train mode when any of the
three HomeLink buttons are pressed.
FCC and RSS-210 Industry Canada
Compliance
This device complies with Part 15 of the FCC
Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
122
MKS (CLE) Canada/United States of America, enUSA, First Printing Universal Garage Door OpenerE142662

U
Under Hood Overview - 3.5L
Ecoboost™......................................................242
Under Hood Overview - 3.7L........................244 Engine Shield............................................................ 245
Universal Garage Door Opener.....................119
HomeLink Wireless Control System.................. 119
Using Adaptive Cruise Control......................167 Blocked Sensor.......................................................... 172
Changing the Set Speed....................................... 170
Detection Issues........................................................ 171
Disengaging Adaptive Cruise Control...............170
Following a Vehicle................................................. 168
Hilly Condition Usage............................................. 170
Low Speed Automatic Cancellation.................170
Overriding Adaptive Cruise Control................... 170
Resuming the Set Speed...................................... 170
Setting Adaptive Cruise Control......................... 167
Setting the Adaptive Cruise Speed.................. 168
Setting the Gap Distance..................................... 169
Switching the System Off...................................... 171
Switching to Normal Cruise Control..................173
Using All-Wheel Drive......................................143 Driving In Special Conditions With All-Wheel
Drive (AWD).......................................................... 145
Operating AWD Vehicles With Mismatched Tires........................................................................\
.. 145
Operating AWD Vehicles With Spare Tires........................................................................\
. 144Using Cruise Control........................................166
Switching Cruise Control Off............................... 167
Switching Cruise Control On............................... 166
Using MyKey With Remote Start Systems...............................................................54
Using Snow Chains..........................................285
Using Stability Control....................................155
Using Traction Control
.....................................153
Switching the System Off..................................... 153
System Indicator Lights and Messages...........153
Using a Switch.......................................................... 153
Using the Information Display Controls..........153
Utilizing the Mediation/Arbitration Program (Canada Only)
.................................................219
V
Vehicle Care........................................................263 General Information............................................... 263
Vehicle Certification Label...........................300
Vehicle Identification Number....................299
Vehicle Storage
.................................................268
Battery........................................................................\
269
Body........................................................................\
..... 268
Brakes........................................................................\
. 269
Cooling system........................................................ 269
Engine........................................................................\
. 269
Fuel system............................................................... 269
General....................................................................... 268
Miscellaneous.......................................................... 269
Removing Vehicle From Storage...................... 269
Tires........................................................................\
..... 269Ventilation
See: Climate Control.............................................. 105
VIN See: Vehicle Identification Number.................299
Voice Control
........................................................66
W
Warning Lamps and Indicators.....................85 Adaptive Cruise Control.......................................... 85
Anti-Lock Braking System..................................... 85
Battery........................................................................\
... 85
Brake System.............................................................. 85
Cruise Control............................................................. 85
Direction Indicator..................................................... 85
Door Ajar....................................................................... 85
Engine Coolant Temperature............................... 86
Engine Oil..................................................................... 86
Fasten Safety Belt.................................................... 86
Front Airbag................................................................ 86
Front Fog Lamps....................................................... 86
Grade Assist................................................................ 86
Heads Up Display...................................................... 86
High Beam................................................................... 86
Low Fuel Level............................................................ 86
Low Tire Pressure Warning.................................... 86
Low Washer Fluid...................................................... 86
Parking Lamps............................................................ 87
Powertrain Fault......................................................... 87
Service Engine Soon................................................. 87
Stability Control......................................................... 87
Stability Control Off................................................. 87
378
MKS (CLE) Canada/United States of America, enUSA, First Printing Index