5626-3. Do-it-yourself maintenance
LS460/LS460L_GE (OM50G06E)
■The initialization operation (vehicles with the tire pressure warning system)
●Make sure to carry out initialization after adjusting the tire inflation pressure.
Also, make sure the tires are cold before carrying out initialization or tire inflation
pressure adjustment.
●If you have accidentally turned the engine switch off during initialization, it is not
necessary to press the reset switch again as initialization will restart automatically
when the engine switch has been turned to IGNITION ON mode for the next time.
●If you accidentally press the reset switch when initialization is not necessary, adjust
the tire inflation pressure to the specified level when the tires are cold, and conduct
initialization again.
■Warning performance of the tire pressure warning system (if equipped)
The warning of the tire pressure warning system will change in accordance with driv-
ing conditions. For this reason, the system may give a warning even if the tire pres-
sure does not reach a low enough level, or if the pressure is higher than the pressure
that was adjusted to when the system was initialized.
■When initialization of the tire pressure warning system has failed (vehicles with the
tire pressure warning system)
Initialization can be completed in a few minutes. However, in the following cases, the
settings have not been recorded and the system will not operate properly. If
repeated attempts to record tire inflation pressure settings are unsuccessful, have
the vehicle inspected by your Lexus dealer.
●When operating the tire pressure warning reset switch, the tire pressure warning
light does not blink 3 times.
●After carrying out the initialization procedure, the tire pressure warning light blinks
for 1 minute then stays on after driving for 20 minutes.
6347-2. Steps to take in an emergency
LS460/LS460L_GE (OM50G06E)
Ensure that the shift lever is in P and depress the brake pedal.
Touch the Lexus emblem side of
the electronic key to the engine
switch.
If any of the doors is opened or closed
after the key was touched to the
switch to start the vehicle, an alarm
will sound to indicate that the start
function cannot detect the key.
Press the engine switch within 10 seconds of the buzzer sounding,
keeping the brake pedal depressed.
In the event that the engine still cannot be started, contact your Lexus
dealer.
■Stopping the engine
Shift the shift lever to P and press the engi ne switch as you normally do when stop-
ping the engine.
■Replacing the key battery
As the above procedure is a temporary measure, it is recommended that the elec-
tronic key battery be replaced immediately when the battery is depleted. ( P. 575)
■Alarm (on some models)
Using the mechanical key to lock the doors will not set the alarm system.
If a door is unlocked using the mechanical key when the alarm system is set, the
alarm may be triggered.
■Changing engine switch modes
Within 10 seconds of the buzzer sounding, release the brake pedal and press the
engine switch.
The engine does not start and modes will be changed each time the switch is
pressed. ( P. 260)
Starting the engine
1
2
3
673
8
8-2. Customization
Vehicle specifications
LS460/LS460L_GE (OM50G06E)
Power
windows
( P. 236)
and moon
roof*1
( P. 240)
One-touch close opera-
tion using the power win-
dow switches on the front
passenger door and each
rear door
OnOff——O
One-touch front passen-
ger window or rear win-
dow close operation using
the power window switch
on the driver’s door
OnOff——O
Mechanical key linked
operationOnOff——O
Wireless remote control
linked operation*2OffOn——O
Linked entry functionOnOff——O
Turn signal
lever
( P. 278)
Times of flashing of the lane
change signal flashers3
5
O—O
7
9
11
Off
Automatic
light control
system
( P. 285)
Light sensor sensitivityStandard-2 to 2O—O
Time elapsed before head-
lights automatically turn off
after doors are closed*2
30 sec-
onds
0 second
O—O
60 sec-
onds
90 sec-
onds
ItemFunctionDefault
setting
Custom-
ized setting123
