2016 Lexus CT200h light

CT200h_OM_OM76197U_(U)
5157-3. Do-it-yourself maintenance
7
Maintenance and care
Unplug the connector while
pressing the lock release.
Turn the bulb base counterclock-
wise.
Set the new light bulb.
Align the 3 tabs on the light bulb with
the mounting, and insert. Turn it
clockwise to set.
Set the connector.
After installing the connector, shake
the bulb base gently to check that it is
not loose, turn the fog lights on once
and visually confirm that no light is
leaking through the mounting.
2
3
4
5

516
CT200h_OM_OM76197U_(U)7-3. Do-it-yourself maintenance
Reinstall the fender liner with 2
screws, a bolt and clip.
■Front turn signal lights (halogen headlights)
Turn the bulb base counterclock-
wise.
Remove the light bulb.
■Front turn signal lights (LED headlights)
Left side
Remove the power control unit
cover.
6
1
2
1

CT200h_OM_OM76197U_(U)
5177-3. Do-it-yourself maintenance
7
Maintenance and care
Turn the bulb base counterclock-
wise.
Remove the light bulb.
Right side
Move the washer fluid filler opening. (P. 5 1 2 )
Turn the bulb base counterclock-
wise.
Remove the light bulb.
2
3
1
2
3

518
CT200h_OM_OM76197U_(U)7-3. Do-it-yourself maintenance
■Rear turn signal lights
Open the back door and remove
the covers and bolts, and remove
the lamp assembly by pulling it
directly backward from the rear
of the vehicle.
Use a flathead screwdriver wrapped
in a cloth.
Turn the bulb base counterclock-
wise.
Remove the light bulb.
■Back-up lightsOpen the back door and remove
the cover.
Use a flathead screwdriver wrapped
in a cloth.
1
2
3
1

CT200h_OM_OM76197U_(U)
5197-3. Do-it-yourself maintenance
7
Maintenance and care
Turn the bulb base counterclock-
wise.
Remove the light bulb.
■Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by your Lexus
dealer.
●Headlight low beams (LED type)
●Parking lights and daytime running lights
●LED fog lights (if equipped)
●Front side marker lights
●Side turn signal lights
●Stop/tail lights
●Rear side marker lights
●High mounted stoplight
●License plate lights
●Outer foot lights
■After replacing the bulbs
2
3
After removing the power control unit cover,
return the cover to original position with the
clips.Push up center portion
Insert
Press
1
2
3

520
CT200h_OM_OM76197U_(U)7-3. Do-it-yourself maintenance
■LED lights
The headlight low beams (LED type), parking
lights, front side marker lights, daytime
running lights, LED fog lights (if equipped), side turn signal lights, rear side marker lights,
stop/tail lights, high mounted stoplight and license plate lights consist of a number of
LEDs. If any of the LEDs burn out, take your vehicle to your Lexus dealer to have the light
replaced.
■Condensation build-up on the inside of the lens
Temporary condensation build-up on the inside of the headlight lens does not indicate a
malfunction. Contact your Lexus dealer for mo re information in the following situations:
●Large drops of water have built up on the inside of the lens.
●Wa t e r h a s b u i l t u p i nside the headlight.
■When replacing light bulbs
P. 5 0 8
WA R N I N G
■Replacing light bulbs
●Be sure to stop the hybrid system and turn off the lights. Do not attempt to replace the
bulb immediately after turning off the lights.
The bulbs become very hot and may cause burns.
●Do not touch the glass portion of the light bulb with bare hands. When it is unavoid-
able to hold the glass portion, use and ho ld with a clean dry cloth to avoid getting
moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
●Fully install light bulbs and any parts used to secure them. Failure to do so may result
in heat damage, fire, or water entering the headlight unit. This may damage the head-
lights or cause condensation to build up on the lens.
●Do not attempt to repair or disassemble light bulbs, connectors, electric circuits or
component parts.
Doing so may result in death or se rious injury due to electric shock.
■To prevent damage or fire
●Make sure bulbs are fully seated and locked.
●Check the wattage of the bulb before installin g to prevent heat damage.

521
CT200h_OM_OM76197U_(U)
8When trouble arises
8-1. Essential informationEmergency flashers .................. 522
If your vehicle has to be stopped in an emergency .... 523
8-2. Steps to take in an emergency If your vehicle needs to be towed ..................................... 524
If you think something is wrong ........................................... 528
If a warning light turns on or a warning buzzer
sounds.......................................... 529
If a warning message is displayed..................................... 536
If you have a flat tire................... 549
If the hybrid system will not start ...............................................558
If the electronic key does not operate properly .....................560
If the 12-volt battery is discharged ................................. 562
If your vehicle overheats ......... 566
If the vehicle becomes stuck ............................................. 570

522
CT200h_OM_OM76197U_(U)8-1. Essential information
Emergency flashers
Press the switch.
All the turn signal lights will flash. To turn
them off, press the
switch once again.
■Emergency flashers
If the emergency flashers are used for a long time while the hybrid system is not operat-
ing (while the “READY” indicator is not illu minated), the 12-volt battery may discharge.
The emergency flashers are used to warn other drivers when the vehicle has
to be stopped in the road due to a breakdown, etc.