2016 JEEP RENEGADE lights

FRONT VIEW
Front View
1 — Headlights
2 — Engine Compartment
3 — Windshield4 — Doors
5 — Exterior Mirrors
6 — Wheels 20 GRAPHICAL TABLE OF CONTENTS

Front View (Trailhawk)
Front View (Trailhawk)
1 — Headlights
2 — Engine Compartment
3 — Windshield4 — Doors
5 — Exterior Mirrors
6 — Wheels
3
GRAPHICAL TABLE OF CONTENTS 21

REAR VIEW
Rear View
1 — Rear Lights
2 — Rear Windshield Wiper
3 — Liftgate 22 GRAPHICAL TABLE OF CONTENTS

Rear View (Trailhawk)
Rear View (Trailhawk)
1 — Rear Lights
2 — Rear Windshield Wiper
3 — Liftgate
3
GRAPHICAL TABLE OF CONTENTS 23

BLIND SPOT MONITORING (BSM) —
IF EQUIPPED..........................87
▫Rear Cross Path (RCP)..................93
▫Mode Of Operation.....................94
▫Blind Spot Monitoring Fault Warnings.......95
▫General Information....................96
EXTERIOR LIGHTS......................97
▫Headlights...........................97
▫Automatic Lighting — If Equipped.........98
▫Daytime Running Lights (DRL) —
If Equipped..........................98
▫Front Fog Lights — If Equipped...........99
▫Parking Lights........................99
▫Headlight Delay.......................99▫Flash-To-Pass........................100
▫High Beams.........................101
▫Turn Signals.........................101
INTERIOR LIGHTS.....................102
▫Front Lights.........................102
▫Interior Lights Dimmer Switch............107
WIPERS AND WASHERS.................108
▫Front Wiper Operation..................108
▫Rear Wiper Operation..................111
▫Windshield Wiper De-Icer — If Equipped....113
WINDOWS...........................114
▫Power Windows......................114
4
GETTING TO KNOW YOUR VEHICLE 29

Push and release the UNLOCK button on the RKE
transmitter once to unlock the driver’s door or twice
within five seconds to unlock all doors and the liftgate.
The turn signal lights will flash to acknowledge the
unlock signal. The illuminated entry system will also
turn on.
1st Push Of Key Fob Unlocks
This feature lets you program the system to unlock either
the driver’s door or all doors on the first push of the
UNLOCK button on the RKE transmitter. To change the
current setting, refer to “Uconnect SETTINGS” in “Mul-
timedia” for further information.
NOTE:If the vehicle is equipped with Passive Entry,
refer to “Keyless Enter-N-Go” in “Getting To Know Your
Vehicle” for further information.To Lock The Doors And Liftgate
If equipped, the doors may be locked by inserting the
vehicle key into the exterior driver’s door lock cylinder.
Push and release the LOCK button on the RKE transmit-
ter to lock all doors and liftgate. The turn signal lights
will flash and the horn will chirp to acknowledge the
signal. Settings in radio can change to lights only, chirp
only, or both.
If the vehicle is equipped with Passive Entry, refer to
“Keyless Enter-N-Go” in “Getting To Know Your Ve-
hicle” for further information.
Key Fob With Remote Control And Integrated Vehicle
Key
If one or more doors are open, or the liftgate is open, the
doors will lock. This is signaled by a quick flash of the
turn signals.
34 GETTING TO KNOW YOUR VEHICLE

NOTE:In a parking lot situation, oncoming vehicles can
be obscured by vehicles parked on either side. If the
sensors are blocked by other structures or vehicles, the
system will not be able to alert the driver.
When RCP is on and the vehicle is in REVERSE, the
driver is alerted using both the visual and audible
alarms, including reducing the radio volume.
WARNING!
RCP is not a Back Up Aid system. It is intended to be
used to help a driver detect an oncoming vehicle in a
parking lot situation. Drivers must be careful when
backing up, even when using RCP. Always check
carefully behind your vehicle, look behind you, and
be sure to check for pedestrians, animals, other
vehicles, obstructions, and blind spots before back-
ing up. Failure to do so can result in serious injury or
death.
Mode Of Operation
Three selectable modes of operation are available in the
Uconnect System. Refer to “Uconnect Settings” in “Mul-
timedia” for further information.
Blind Spot Alert Lights Only
When operating in Blind Spot Alert mode, the BSM
system will provide a visual alert in the appropriate side
view mirror based on a detected object. However, when
the system is operating in Rear Cross Path (RCP) mode,
the system will respond with both visual and audible
alerts when a detected object is present. Whenever an
audible alert is requested, the radio is muted.
Blind Spot Alert Lights/Chime
When operating in Blind Spot Alert Lights/Chime mode,
the BSM system will provide a visual alert in the appro-
priate side view mirror based on a detected object. If the
turn signal is then activated, and it corresponds to an
94 GETTING TO KNOW YOUR VEHICLE

alert present on that side of the vehicle, an audible chime
will also be sounded. Whenever a turn signal and de-
tected object are present on the same side at the same
time, both the visual and audible alerts will be issued. In
addition to the audible alert, the radio (if on) will also be
muted.
NOTE:Whenever an audible alert is requested by the
BSM system, the radio is also muted.
When the system is in RCP, the system will respond with
both visual and audible alerts when a detected object is
present. Whenever an audible alert is requested, the radio
is also muted. Turn/hazard signal status is ignored; the
RCP state always requests the chime.
Blind Spot Alert Off
When the BSM system is turned off, there will be no
visual or audible alerts from either the BSM or RCP
systems.NOTE:The BSM system will store the current operating
mode when the vehicle is shut off. Each time the vehicle
is started the previously stored mode will be recalled and
used.
Blind Spot Monitoring Fault Warnings
Sensor Blinded
In the case of a sensor blinded:
•BSM Mirror Warning Lights are turned on continu-
ously.
•A instrument cluster message will display“Blind Spot
Monitoring Unavailable - Wipe Rear Bumper Cor-
ners.”
NOTE:The rear bumper must be clean and free of any
obstructing debris.4
GETTING TO KNOW YOUR VEHICLE 95