2016 JEEP RENEGADE bulb

4. Remove the bulb from the bulb socket by pulling the
bulb straight out.5. Insert the new bulb, making sure that it is locked into
place
6. Reinstall the socket in to the transparent lens assembly.
7. Reinstall the cover on the outside rear view mirror,
making sure it is locked into place.
Rear Tail Lamps
Contain the following:
•Position lights
•Stop lights
•Direction indicator
•REVERSE lights
Bulb And Socket Assembly
1 — Bulb
2 — Bulb Socket 458 IN CASE OF EMERGENCY

To replace the bulbs proceed as follows:
1. Open the liftgate.
2. Using a suitable tool remove the door as shown.
3. Using a suitable tool remove fastener.4. Disconnect the electrical connector by pushing the
release.
Trim Panel Door
Rear Lamp Fastener and Electrical Connector
1 — Fastener
2 — Electrical Connector
8
IN CASE OF EMERGENCY 459

7. Replace the bulb as necessary. 8. Insert the new bulb, making sure it is properly locked;
9. Reassemble the lamp assembly on the rear tail lamp
housing, tightening the screws.
10. Reposition the rear tail lamp on the car.
11. Secure the fastener of the rear tail lamp and reconnect
the electrical connector.
12. Reinstall the door making sure of its correct locked
13. Finally close the tailgate.
3th Stop Lamp
The CHMSL is LED. For their replacement see your
authorized dealer.
Rear Tail Lamp Holder
1 — Tail Light
2 — Reverse Bulb
3 — Position Light/Stop Light/Turn Signal
8
IN CASE OF EMERGENCY 461

License Plate Lights
To replace the bulbs proceed as follows:
1. Using a suitable tool remove the license plate lens.
2. Remove the bulbs from the individual side contacts.
3. Insert the new bulbs, and ensure that they are properly
locked between the contacts.
4. Reinstall the license plate lens.
License Plate Light Location
License Plate Light
462 IN CASE OF EMERGENCY

NOTE:If removal the license plate lens using a screw-
driver, be sure to cover the tip of the screwdriver with a
cloth so no damage is done to the lenses or the vehicle
paint.
Replacing Interior Bulbs
Front Courtesy Light
To replace the bulbs proceed as follows:
1. Using a suitable tool remove the front courtesy light as
shown.
Front Courtesy Light Housing8
IN CASE OF EMERGENCY 463

2. Release the retainer clips and bulb housing as shown.
3. Replace the bulbs by pulling straight out of bulb
housing.4. Insert the new bulbs, making sure that they are
properly locked.
5. Reassemble the bulb housing and courtesy light hous-
ing making sure that they are properly locked.
Front Courtesy Bulb Housing
1 — Retaining Clips
2 — Bulb Housing
Front Courtesy Bulb Housing
464 IN CASE OF EMERGENCY

6. Install the front courtesy light making sure that it is
properly locked.
Dome Light Vanity Mirror
To replace the bulbs proceed as follows:
1. Lift the cover of the mirror and pull out the visor
mirror light cover.
2. Replace the bulb, releasing it from the side contacts,
and then insert the new bulb, making sure that it is
properly locked between the contacts.
3. Reinstall the visor mirror light cover making sure that
it is properly locked.
4. Finally lower the visor mirror cover to the mirror.
Visor
1 — Visor Mirror Cover
2 — Visor Mirror Light8
IN CASE OF EMERGENCY 465

Dome Light Glove Compartment
To replace the bulb proceed as follows:
1. Open the glove compartment;
2. Place your fingers inside the light assembly, pull the
bulb to replace it.3. Insert the new bulb, making sure it is properly locked.
Rear Dome Light — Without Retractable Roof
To replace the bulbs proceed as follows:
1. Using a suitable tool release the lamp assembly at both
the ends.
2. Open the flap and replace the bulb.
Bulb Removal/Installation
466 IN CASE OF EMERGENCY