2016 JEEP RENEGADE engine

Electronic Speed Control — If Equipped
•Do not use in hilly terrain or with heavy loads.
•When using the speed control, if you experience speed
drops greater than 10 mph (16 km/h), disengage until
you can get back to cruising speed.
•Use speed control in flat terrain and with light loads to
maximize fuel efficiency.
Cooling System
To reduce potential for engine and transmission over-
heating, take the following actions:
City Driving
When stopped for short periods of time, shift the trans-
mission into NEUTRAL and increase engine idle speed.
Highway Driving
Reduce speed.
Air Conditioning
Turn off temporarily.
7
STARTING AND OPERATING 429

Recreational Towing
Models With Front-Wheel Drive (FWD)
Recreational towing is allowed ONLY if the front wheels
are OFF the ground. This may be accomplished using a
tow dolly (front wheels off the ground) or vehicle trailer
(all four wheels off the ground). If using a tow dolly,
follow this procedure:
•Properly secure the dolly to the tow vehicle, following
the dolly manufacturer’s instructions.
•Drive the front wheels onto the tow dolly.
•Apply the Electronic Parking Brake (EPB). Place the
transmission in PARK. Turn the engine OFF.
•Properly secure the front wheels to the dolly, following
the dolly manufacturer’s instructions.
•Turn the ignition to the MAR/RUN position, but do
not start the engine.•Press and hold the brake pedal.
•Release the Electric Park Brake (EPB).
•Turn the ignition OFF, remove the key, and release the
brake pedal.
CAUTION!
•DO NOT flat tow this vehicle. Damage to the
drivetrain will result. If this vehicle requires tow-
ing, make sure the drive wheels are OFF the
ground.
•Ensure that the Electric Park Brake is released, and
remains released, while being towed.
•Towing this vehicle in violation of the above re-
quirements can cause severe transmission damage.
Damage from improper towing is not covered un-
der the New Vehicle Limited Warranty.
7
STARTING AND OPERATING 431

IN CASE OF EMERGENCY
CONTENTS
HAZARD WARNING FLASHERS...........435
ASSIST AND 9–1–1 — IF EQUIPPED........435
BULB REPLACEMENT...................442
▫General Information....................442
▫Replacement Bulbs.....................443
▫Replacing Exterior Bulbs................445
▫Replacing Interior Bulbs.................463
FUSES...............................469
▫General Information....................470
▫Access To The Fuses...................471▫Engine Compartment Fuses/Distribution
Unit...............................472
▫Body Computer Fuse Center..............476
▫Rear Cargo Fuse/Relay Distribution Unit.....480
JACKING AND TIRE CHANGING..........483
▫Jack Location/Spare Tire Stowage.........484
▫Preparations For Jacking................486
▫Jacking Instructions...................486
▫Road Tire Installation...................494
8

TIRE SERVICE KIT STORAGE..............495
▫Tire Service Kit — If Equipped............495
JUMP STARTING......................499
▫Preparations For Jump Start..............500
▫Jump Starting Procedure................502
Enhanced Accident Response System.........504
▫System Reset Procedure.................504
REFUELING IN EMERGENCY.............506
IF YOUR ENGINE OVERHEATS............506SHIFT LEVER OVERRIDE................507
IGNITION KEY REMOVAL OVERRIDE.......509
FREEING A STUCK VEHICLE.............512
TOWING A DISABLED VEHICLE...........514
▫Front Wheel Drive (FWD)................515
▫Four-Wheel Drive (4WD)................516
EMERGENCY TOW HOOKS —
IF EQUIPPED.........................516
434 IN CASE OF EMERGENCY

Replacing Exterior Bulbs
Headlamps
Hi/Lo Beam Light Halogen
To replace the bulbs proceed as follows:
1. Open the engine compartment and remove the head-
lamp bulb cap.
Headlamp Bulb Cap8
IN CASE OF EMERGENCY 445

4. Install the new headlamp bulb making sure it is
properly locked.5. Install the headlamp bulb and socket; turn it clockwise
making sure it is properly locked.
WARNING!
Carry out the operation of replacing lamps only with
the engine off. Also make sure that the engine is cold,
to avoid the danger of burns.
Headlamp Bulb8
IN CASE OF EMERGENCY 447

Side Indicators
Front Side Indicators
To replace the bulb proceed as follows:
1. Operating from inside the engine compartment using
a suitable tool release the retaining clip.2. Remove lamp assembly by sliding it toward the out-
side.
Lamp Retaining Clip
Lamp Assembly
8
IN CASE OF EMERGENCY 453

WARNING!(Continued)
•Before replacing a fuse, make sure that the ignition
is off and that all the other services are switched off
and/or disengaged.
•If the replaced fuse blows again, contact an autho-
rized dealer.
•If a general protection fuse for safety systems (air
bag system, braking system), power unit systems
(engine system, gearbox system) or steering system
blows, contact an authorized dealer.
General Information
The fuses protect electrical systems against excessive
current.
When a device does not work you must check the
electrical circuit inside the fuse for a break/melt.Also please be aware that when using power outlets for
extended periods of time with the engine off may result
in vehicle battery discharge.
Blade Fuses
1 — Electrical Circuit
2 — Blade Fuse With Good Electrical Circuit
3 — Blade Fuse With Bad Electrical Circuit 470 IN CASE OF EMERGENCY