2016 JEEP PATRIOT turn signal

WARNING!
• Any voice commanded system should be used only in safe driving conditionsfollowing applicable laws regarding phone use. Your attention should be
focused on safely operating the vehicle. Failure to do so may result in a
collision causing you and others to be severely injured or killed.
• In an emergency, to use Uconnect Phone, your mobile phone must be:
• turned on
• paired to Uconnect Phone
• have network coverage
UCONNECT VOICE COMMAND
Voice Command Operation
The Uconnect Voice Command system allows you to control your AM, FM radio,
satellite radio, disc player, HDD, Uconnect Phone, a memo recorder, and supported
portable media devices.
• When you push the “Voice Command” button
located on the radio faceplate
or steering wheel, you will hear a beep. The beep is your signal to give a command.
If you do not say a command within a few seconds, the system will present you with
a list of options. If you ever want to interrupt the system while it lists options, push
the “Voice Command” button
, listen for the BEEP, and say your command.
NOTE:
U.S. residents visit driveuconnect.com for more info on which voice command
features apply to your vehicle. Canadian residents visit driveuconnect.ca for more
info on which voice command features apply to your vehicle.
• Start a dialogue by pushing the “Voice Command” button
, you will hear a
beep. The beep is your signal to give a command. Below are a list of voice
commands for each of the different modes:
While In: Voice Command Example:
Main Menu “Radio AM” (to switch to the AM radio mode)
“Radio FM” (to switch to the FM radio mode)
“Satellite Radio” (to switch to the Satellite radio mode) “Disc” (to switch to the disc mode)
“USB” (to switch to the USB mode)
“Bluetooth Streaming” (to switch to the Bluetooth Stream- ing mode)
“Memo” (to switch to the memo recorder)
“System Setup” (to switch to system setup)
ELECTRONICS
75

Auto Unlock Doors On Exit
To have all of the vehicle doors unlock when any door is opened:
• Enter your vehicle and close all the doors, and fasten your seat belt.
• Cycle the ignition switch between the LOCK and ON position four times, ending inthe LOCK position (do not start the engine).
• Push the power door UNLOCK switch to unlock the doors. A single chime will indicate that programming is complete.
Auto Door Lock
To have the doors lock automatically when the vehicle’s speed exceeds 15 mph
(24 km/h):
• Enter your vehicle and close all the doors.
• Cycle the ignition switch between LOCK and ON and then back to LOCK fourtimes, ending up in the LOCK position (do not start the engine).
• Push the power door LOCK switch to lock the doors. A single chime will indicate that programming is complete.
Sound Horn With Lock
To turn the horn chirp on or off when the doors are locked:
• Push the LOCK button for at least four seconds, but no longer than 10 seconds.Then, push the PANIC button while still holding the LOCK button.
• Release both buttons at the same time.
Flashing Lights With Lock
The turn signal lights flash when the doors are locked, which can be turned on or off.
To turn this feature on or off:
• Push and hold the UNLOCK button and the LOCK button at the same time for at least four seconds, but no longer than 10 seconds.
• Release both buttons at the same time.
ELECTRONICS
80

3. Push and hold the HomeLink button you want to program while you push and holdthe hand-held transmitter button.
4. Continue to hold both buttons and observe the indicator light. The HomeLink indicator will flash slowly and then rapidly after HomeLink has received the
frequency signal from the hand-held transmitter. Release both buttons after the
indicator light changes from slow to rapid.
5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually be found where the hanging antenna wire
is attached to the garage door opener motor. Firmly push and release the
“LEARN” or “TRAINING” button.
NOTE:
You have 30 seconds in which to initiate the next step after the LEARN button has
been pushed.
6. Return to the vehicle and push the programmed HomeLink button twice (holding the button for two seconds each time). If the device is plugged in and activates,
programming is complete.
NOTE:
If the device does not activate, push the button a third time (for two seconds) to
complete the training.
7. To program the remaining two HomeLink buttons, repeat each step for each remaining button. DO NOT erase the channels.
Programming A Non-Rolling Code
NOTE:
For programming Garage Door Openers manufactured before 1995.
1. Turn the ignition switch to the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from theHomeLink button you wish to program while keeping the HomeLink indicator light
in view.
3. Push and hold the HomeLink button you want to program while you push and hold the hand-held transmitter button.
4. Continue to hold both buttons and observe the indicator light. The HomeLink indicator will flash slowly and then rapidly after HomeLink has received the
frequency signal from the hand-held transmitter. Release both buttons after the
indicator light changes from slow to rapid.
5. Push and hold the programmed HomeLink button and observe the indicator light. If the indicator light stays on constantly, programming is complete and the garage
door (or device) should activate when the HomeLink button is pushed.
6. To program the two remaining HomeLink buttons, repeat each step for each remaining button. DO NOT erase the channels.
ELECTRONICS
82

When the system detects a malfunction, the telltale will flash for approximately one
minute and then remain continuously illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the malfunction exists. When the malfunc-
tion indicator is illuminated, the system may not be able to detect or signal low tire
pressure as intended. TPMS malfunctions may occur for a variety of reasons,
including the installation of replacement or alternate tires or wheels on the vehicle
that prevent the TPMS from functioning properly. Always check the TPMS malfunc-
tion telltale after replacing one or more tires or wheels on your vehicle to ensure that
the replacement or alternate tires and wheels allow the TPMS to continue to function
properly.
NOTE:
Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air
temperature change. Keep this in mind when checking tire pressure inside a garage,
especially in the Winter. Example: If garage temperature is 68°F (20°C), and the
outside temperature is 32°F (0°C), then the cold tire inflation pressure should be
increased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this
outside temperature condition.
CAUTION!
The TPMS has been optimized for the original equipment tires and wheels. TPMS
pressures and warning have been established for the tire size equipped on your
vehicle. Undesirable system operation or sensor damage may result when using
replacement equipment that is not of the same size, type, and/or style. Aftermar-
ket wheels can cause sensor damage. Do not use tire sealant from a can, or
balance beads if your vehicle is equipped with a TPMS, as damage to the sensors
may result.
– Brake Warning Light
This light monitors various brake functions, including brake fluid level and parking
brake application. If the brake light turns on, it may indicate that the parking brake
is applied, that the brake fluid level is low, or that there is a problem with the brake
system master cylinder reservoir.
If the light remains on when the parking brake has been disengaged, and the fluid
level is at the full mark on the master cylinder reservoir, it indicates a possible brake
hydraulic system malfunction or that a problem with the Brake Booster has been
detected by the Anti-Lock Brake System (ABS)/Electronic Stability Control (ESC)
system. In this case, the light will remain on until the condition has been corrected.
If the problem is related to the brake booster, the ABS pump will run when applying
the brake, and a brake pedal pulsation may be felt during each stop.
WHAT TO DO IN EMERGENCIES
91

The “ESC Activation/Malfunction Indicator Light” starts to flash as soon as the tires
lose traction and the ESC system becomes active. If the light begins to flash during
acceleration, ease up on the accelerator and apply as little throttle as possible. Be
sure to adapt your speed and driving to the prevailing road conditions. The light also
flashes when Traction Control System (TCS) is active. To improve the vehicle's
traction when starting off in deep snow, sand or gravel, it may be desirable to switch
the ESC system to Partial Off mode by momentarily pushing the ESC Off
switch.
INSTRUMENT CLUSTER INDICATOR LIGHTS
– Turn Signal Indicator
The arrows will flash with the exterior turn signals when the turn signal lever is
operated. A tone will chime, and a EVIC message will appear if either turn signal is
left on for more than 1 mile (1.6 km).
NOTE:
If either indicator flashes at a rapid rate, check for a defective outside light bulb.
– High Beam Indicator
Indicates that headlights are on high beam.
– Front Fog Light Indicator
This indicator will illuminate when the front fog lights are on.
– Vehicle Security Light
This light will flash rapidly for approximately 15 seconds when the vehicle security
alarm is arming. The light will flash at a slower speed continuously after the alarm is
set. The security light will also come on for about three seconds when the ignition is
first turned on.
– 4WD Indicator
This light indicates the vehicle is in 4-wheel drive (4WD) mode.
– Electronic Stability Control (ESC) OFF Indicator Light
This light indicates the Electronic Stability Control (ESC) is off.
– Cruise Indicator
This indicator shows that the Electronic Speed Control System is ON.
– Hill Descent Control Indicator — If Equipped
This indicator will illuminate when Hill Descent Control (HDC) has been selected
using the Hill Descent Control Switch.
WHAT TO DO IN EMERGENCIES
94

REPLACEMENT BULBS
All the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not
approved and should not be used for replacement
Interior Bulbs
Bulb Number
Front Header Lamp T578
Center Dome Lamp T578
Rear Cargo Lamp/Flashlight 8–A35LF
Exterior Bulbs
Bulb Number
Low Beam/High Beam Headlamp H13
Front Park/Turn Signal/Side Marker Lamp 3757KA
Front Fog Lamp PSX24W
Center High Mounted Stop Lamp
(CHMSL) LED Assembly (Serviced At Authorized
Dealer)
Rear Tail/Turn/Stop Lamp 3157
Backup Lamp W16W (921)
License Lamp W5W
MAINTAINING YOUR VEHICLE
128

Electronic Stability Control (ESC)
Activation/Malfunction Indicator
Light ................93
Electronic Throttle Control (ETC)
Indicator Light...........90
FrontFogLightIndicator .....94
HighBeamIndicator .......94
Instrument Cluster Warning
Lights ................89
Malfunction Indicator Light
(MIL).................93
Oil Pressure Warning Light ....89
Tire Pressure Monitoring System
(TPMS) Light ............90
Turn Signal Indicator .......94
Vehicle Security Light .......94
Clutch .................118
ClutchFluid..............118
Compact Spare Tire ..........126
Compass Calibration ..........78
Coolant (Antifreeze) .........116
Cooling System ............118
Adding Coolant (Antifreeze) . .118
Coolant Level ...........118
Disposal Of Used Coolant ....118
Drain, Flush, And Refill .....118
Inspection ............118
Points To Remember ......118
Pressure Cap ...........118
Selection Of Coolant
(Antifreeze) ........116, 118
Corrosion Protection .........118
Customer Assistance ......129, 130
Defects, Reporting ..........130
Delay (Intermittent) Wipers ......32
Dimmer Switch, Headlight ......30
Disabled Vehicle Towing ........89
Disarming, Security System ......12
Disposal Antifreeze (Engine Coolant) . . .118
Driver's Seat Back Tilt .........26
Electronics Your Vehicle's Sound System . . .42
Electronic Speed Control (Cruise Control) ................34
Electronic Stability Control (ESC) . .93 Electronic Throttle Control Warning
Light.................90
Electronic Vehicle Information Center (EVIC) ................79
Average Fuel Consumption ....78
Distance Traveled .........78
Electronic Vehicle Information Cen-
ter(EVIC) ..............78
ExitMenu ..............78
Language (Selecting The
Language) ..............79
Travel Time .............78
Trip Functions ...........78
Units (Set Units) ..........79
Emergency, In Case Of Jacking ...............96
Jump Starting ..........103
Overheating ............95
Towing ............89,107
Engine Air Cleaner ............118
Break-In Recommendations . . .29
Checking Oil Level ........118
Compartment ........112, 114
Coolant (Antifreeze) .......116
Cooling ...............118
Jump Starting ..........103
Oil .............. 116, 118
Oil Filler Cap ...........118
Oil

Selection ...........118
Overheating ............95
Enhanced Accident Response Feature ...............109
Exhaust System ............118
Filters Air Cleaner ............118
EngineOil ......... 116, 118
Engine Oil Disposal .......118
Flashers TurnSignal .............94
Fluid, Brake ..............117
Fluid Capacities ............116
Fluids, Lubricants And Genuine Parts ................116
FogLights .............30,94
FoldingRearSeat ...........26
FoldingRearSeat(Sedan) ......26
INDEX
135

InstrumentCluster ........30
LowFuel ..............89
SeatBeltReminder ........93
Security Alarm...........94
Tire Pressure Monitoring
(TPMS) ...............90
Transmission Warning .......93
TurnSignal ..........29,31
Locks Liftgate, Tailgate ..........10
Lubrication, Body ...........118
Lumbar Support ............26
Maintenance Free Battery ......118
Maintenance,General ........118
MaintenanceProcedures.......118
Maintenance Record .........122
MaintenanceSchedule........118
Malfunction Indicator Light (Check Engine)................93
Manual Transmission Lubricant Selection .......117
Master Cylinder (Brakes) .......118
MediaCenterRadio........51,54
MOPAR Accessories .........131
Multi-Function Control Lever .....29
Navigation ................63
Navigation System (Uconnect GPS) ...........63
Navigation Voice Prompt Volume . . .63
New Vehicle Break-In Period .....29
OilChangeIndicator..........95
Oil,Engine ........... 116, 118
Capacity ..............116
Change Interval .........118
Checking .............118
Disposal ..............118
Filter ............ 116, 118
Filter Disposal ..........118
Materials Added To .......118
Recommendation .....116, 118
Viscosity .............118
Oil Filter, Selection ..........118
Oil Pressure Light ...........89
Outlet Power ................84 Overheating, Engine
..........95
PaintCare...............118
Panic Alarm ...............10
Passing Light ..............30
Phone (Pairing) .............73
Phone (Uconnect) ...........72
Placard, Tire And Loading Information .............125
Power Inverter ...............83
Outlet (Auxiliary Electrical
Outlet) ...............84
Sunroof ...............40
Power Seats Down.................24
Forward ...............24
Rearward ..............24
Tilt ..................24
Up ..................24
Power Steering Fluid .........117
Power Transfer Unit ..........117
Preparation For Jacking ........97
Programmable Electronic Features . .79
Radio Presets ........45,48,52,57
RadioOperation.....45,48,52,57
R
earCamera ..............37
Rear ParkSense System ........37
Rear Seat, Folding ...........26
Rear Wiper/Washer ...........33
Recreational Towing ..........88
Refrigerant ...............118
Remote Keyless Entry (RKE) Arm The Alarm ...........12
Disarm The Alarm .........12
Lock The Doors ...........10
Panic Alarm ............10
Remote Keyless Entry (RKE) . . .10
Unlock The Doors .........10
Remote Starting How To Use Remote Start .....11
KeyFob ...............11
Remote Starting System .....11
Remote Starting System ........11
Replacement Bulbs ..........128
Reporting Safety Defects .......130
INDEX
137