2016 Hyundai Creta Fog lamp

1-3
Your vehicle at a glance
ExtErior ovErviEw (ii)
1
OGC014002
■Rear view
The actual shape may differ from the illustration. 1. Antenna ...
................................................43
2. Fuel filler lid ...........................................328
3. Rear parking assist system* .................385
4. Rear combination lamp .........................784
5. Rear window wiper blade ......................745
6. High mounted stop lamp .......................786
7. Rearview camera* .................................384
8. Tailgate ..................................................319
9. Rear fog light* .......................................354
* : if equipped

3-75
Convenient features of your vehicle
High beam operation
To turn on the high beam headlamp,
push the lever away from you. The
lever will return to its original position.
The high beam indicator will light
when the headlamp high beams are
switched on.
To turn off the high beam headlamp,
pull the lever towards you. The low
beams will turn on. To flash the high beam headlights,
pull the lever towards you, then
release the lever. The high beams
will remain ON as long as you hold
the lever towards you.
Rear fog light (if equipped)
Vehicle with front fog light
To turn on the rear fog light:
Position the light switch in the park
ing light position, turn the light switch
(1) to the front fog light position, and
then turn the light switch (1) to the
rear fog light position.
To turn the rear fog lights off, do one
of the following:
• Turn off the parking light switch.
• Turn the light switch to the rear fog light position again.
• When the light switch is in the parking light position, if you turn off
the front fog light, the rear fog light
will also turn off.
OGS045060L
Do not use high beam when there
are other vehicles approaching you.
Using high beam could obstruct the
other driver's vision.
WARNING
OGS045061L
OGS045062L

3-76
Convenient features of your vehicle
3
Vehicle without front fog light
To turn on the rear fog light:
Position the light switch in the head
lamp position, and then turn the light
switch (1) to the rear fog light position.
To turn the rear fog lights off, do one
of the following:
• Turn off the headlamp switch.
• Turn the light switch to the rear foglight position again.
Front fog light (if equipped)
Fog lights are used to provide
improved visibility when visibility is
poor due to fog, rain or snow, etc.
1. Turn on the park light.
2. Move the light switch (1) to the front fog light position.
3. To turn off the front fog light, turn the light switch to the front fog light
position again or turn off the park
ing light.
When in operation, the fog lights
consume large amounts of vehicle
electrical power. Only use the fog
lights when visibility is poor.
NOTICE
OGS045063L

3-78
Convenient features of your vehicle
3
Daytime running light (DRL)
(if equipped)
The Daytime Running Lights (DRL)
can make it easier for others to see
the front of your vehicle during the
day, especially after dawn and beforesunset.
The DRL system will turn the dedi
cated lamp OFF when:
1. The headlights or front fog lightsare in the ON position.
2. The engine is turned off.
Headlamp leveling device
To adjust the headlamp beam level
according to the number of the pas
sengers and loading weight in the
luggage area, turn the beam leveling
switch. The higher the number of the switch
position, the lower the headlamp
beam level. Always keep the head
lamp beam at the proper leveling
position, or headlights may dazzle
other road users.
Listed below are the examples of
proper switch settings. For loading
conditions other than those listed
below, adjust the switch position so
that the beam level may be the near
est as the condition obtained accord
ing to the list.
OGS045064L
Loading conditionSwitch position
Driver only 0
Driver + Front passenger 0
Full passengers
(including driver) 1
Full passengers (including
driver) + Maximum permis
sible loading 2
Driver + Maximum permis
sible loading 3

7-69
7
Maintenance
Inner Compartment Fuse Panel
ITEMNameSymbolFuse RatingCircuit Protected
FUSE
RR HTD30ARear Defogger Relay, Rear Defogger
TURN15ABody Control Module
SPARE20A
DOOR LOCK20ADoor Lock/Unlock Relay, Door Actuator, Tail Gate Unlock Relay, Tail Gate Latch
PDM115ASmart Key Control Module
WASHER15AMulti Function Switch
A/CON10AAir Condition Module(Manual, Auto), Cluster Ionizer, Blower Relay
MODULE 502'8/(
10AElectronic chromic mirror, Head lamp leveling Switch, Head Lamp LH/RH
MODULE 402'8/(
10ASmart key Control Module, Body Control Module
SPARE20A
SPARE20A
PDM 22210ASmart Key Control Module
* G4FC : Gamma 1.6 (Gasoline), D4FC : UII 1.4 (Diesel), D4FB : UII 1.6 (Diesel)

7-83
7
Maintenance
6. Install a new headlight bulb and
snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
BiFunction projection
headlamp
This headlamp is bifunction type that
switches the low beam to high or the
high beam to low using solenoid sys
tem. So, the moving sound may be
heard when the headlamp switches
the low beam to high or the high beam
to low and it does not indicate mal
function of the headlamp.
Turn signal light
1. Remove the turn signal light bulb cover by turning it counterclock
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
Front fog light bulb replacement
1.Remove the under cover by rotating the screws and bolts.
2.Reach your hand into the back of the front bumper.
3.Disconnect the power connector from the socket.
4.Remove the bulbsocket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5.Install the new bulbsocket into the housing by aligning the tabs on the
socket with the slots in the hous
ing. Push the socket into the hous
ing and turn the socket clockwise.
6.Connect the power connector to the socket.
7.Reinstall the front bumper under cover.
i

4.Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5.Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
6.Insert a new bulb into the socket.
7.Install the socket into the assembly by aligning the tabs on the socket
with the slots on the assembly and
turning the socket clockwise.Rear fog lamp (if equipped)
1.Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
2.Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
3.Insert a new bulb in the socket.
4.Reinstall the light assembly to the body of the vehicle.
High mounted stop light
If the light does not operate, we rec
ommend that the vehicle be checked
by an authorized HYUNDAI dealer.
7-86
Maintenance
OGC074031

bulb wattaGE
8-3
8
Specifications & Consumer information
* : If equipped
Light BulbWattage (W)
Front Headlight
Type A 60/55
Type B 60
Turn signal light 21
Position light Type A 5
Type B LED
Static bending light (SBL)* 55
Fog light* 35
Side Repeater light (Outside mirror) Type A 5
Type B LED
Daytime running light*21/5
Rear Rear combination light Stop/Tail 21/5
Tail 21/5
Turn signal 21
Back up 16
High mounted stop light 5
License plate light 5
Fog light*21
Interior Map lamp
8
Room lamp 8
Sunvisor lamp5
Luggage room lamp 8