2016 Hyundai Creta ABS

7-83
7
Maintenance
6. Install a new headlight bulb and
snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
BiFunction projection
headlamp
This headlamp is bifunction type that
switches the low beam to high or the
high beam to low using solenoid sys
tem. So, the moving sound may be
heard when the headlamp switches
the low beam to high or the high beam
to low and it does not indicate mal
function of the headlamp.
Turn signal light
1. Remove the turn signal light bulb cover by turning it counterclock
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
Front fog light bulb replacement
1.Remove the under cover by rotating the screws and bolts.
2.Reach your hand into the back of the front bumper.
3.Disconnect the power connector from the socket.
4.Remove the bulbsocket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5.Install the new bulbsocket into the housing by aligning the tabs on the
socket with the slots in the hous
ing. Push the socket into the hous
ing and turn the socket clockwise.
6.Connect the power connector to the socket.
7.Reinstall the front bumper under cover.
i

7-85
7
Maintenance
Outside light
1. Open the tailgate
2. Loosen the light assembly retaining screws with a crosstip screw
driver.
3. Remove the rear combination light assembly from the body of the
vehicle. 4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
Inside lamp
Backup light/Tail light
1. Turn off the engine.
2. Open the tailgate.
3. Remove the service cover using a flatblade screwdriver.
OGC074046
Stop/Tail
Turn signal
Back upTailOGC074026
OGC074027
OGC074028
OGC074029

4.Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5.Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
6.Insert a new bulb into the socket.
7.Install the socket into the assembly by aligning the tabs on the socket
with the slots on the assembly and
turning the socket clockwise.Rear fog lamp (if equipped)
1.Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
2.Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
3.Insert a new bulb in the socket.
4.Reinstall the light assembly to the body of the vehicle.
High mounted stop light
If the light does not operate, we rec
ommend that the vehicle be checked
by an authorized HYUNDAI dealer.
7-86
Maintenance
OGC074031

Interior light bulb replacement1. Using a flatblade screwdriver,gently pry the lens from the interi
or lamp housing.
2. Remove the bulb by pulling it straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior lamp housing notches and snap
the lens into place.
Use care not to dirty or damage lens,
lens tab, and plastic housings.
NOTICE
7-88
Maintenance
Prior to working on the Interior
lamps, ensure that the “OFF” but
ton is depressed to avoid burning
your fingers or receiving an elec
tric shock.
WARNING
■Map lamp (if equipped)
■Room lampOGS075047/OGS075049/OGS075048
■Luggage room lamp

7-96
Maintenance
EMISSION CONTROl SYSTEM
The emission control system of your
vehicle is covered by a written limited
warranty. Please see the warranty
information contained in the Service
Passport in your vehicle.
Your vehicle is equipped with an
emission control system to meet all
emission regulations.
There are three emission control
systems which are as follows.
(1) Crankcase emission control system
(2) Evaporative emission control sys tem
(3) Exhaust emission control system
In order to assure the proper function
of the emission control systems, it is
recommended that you have your
car inspected and maintained by an
authorized HYUNDAI dealer in
accordance with the maintenance
schedule in this manual.1. Crankcase emission control
system
The positive crankcase ventilation
system is employed to prevent air
pollution caused by blowby gases
being emitted from the crankcase.
This system supplies fresh filtered air
to the crankcase through the air
intake hose. Inside the crankcase,
the fresh air mixes with blowby
gases, which then pass through the
PCV valve into the induction system.
2. Evaporative emission control
system
The Evaporative Emission Control
System is designed to prevent fuel
vapors from escaping into the atmos
phere.
Canister
Fuel vapors generated inside the fuel
tank are absorbed and stored in the
onboard canister. When the engine is
running, the fuel vapors absorbed in
the canister are drawn into the surge
tank through the purge control sole
noid valve.
Purge Control Solenoid Valve(PCSV)
The purge control solenoid valve is
controlled by the Engine Control
Module (ECM); when the engine
coolant temperature is low during
idling, the PCSV closes so that evap
orated fuel is not taken into the
engine. After the engine warms up
during ordinary driving, the PCSV
opens to introduce evaporated fuel to
the engine.