2016 Hyundai Creta ABS

5-36
Driving your vehicle
Information
When you jump start your vehicle
because of a drained battery, the ABS
warning light ( ) may turn on at the
same time. This happens because of
the low battery voltage. It does not
mean your ABS is malfunctioning.
Have the battery recharged before
driving the vehicle.Electronic Stability Control (ESC)
(if equipped)
The Electronic Stability Control
(ESC) system helps to stabilize the
vehicle during cornering maneuvers.
ESC checks where you are steering
and where the vehicle is actually
going. ESC applies braking pressure
to any one of the vehicle’s brakes
and intervenes in the engine man
agement system to assist the driver
with keeping the vehicle on the
intended path. It is not a substitute
for safe driving practices. Always
adjust your speed and driving to the
road conditions.
i
When you drive on a road having
poor traction, such as an icy road,
and apply your brakes continuous
ly, the ABS will be active continu
ously and the ABS warning light
() may illuminate. Pull your car
over to a safe place and turn the
engine off.
Restart the engine. If the ABS
warning light is off, then your ABS
system is normal. Otherwise, you
may have a problem with your
ABS system. We recommend that
you contact an authorized
HYUNDAI dealer as soon as pos
sible.
CAUTION
OGC054007

The ESC OFF indicator light comes
on when the ESC is turned off with
the button.
Driving with wheels and tires with dif
ferent sizes may cause the ESC sys
tem to malfunction. Before replacing
tires, make sure all four tires and
wheels are the same size. Never
drive the vehicle with different sized
tires and wheels installed.
ESC OFF usage
When Driving
The ESC OFF mode should only be
used briefly to help free the vehicle if
stuck in snow or mud by temporarily
stopping operation of the ESC to
maintain wheel torque.
To turn ESC off while driving, press
the ESC OFF button while driving on
a flat road surface.To prevent damage to the transaxle:
•Do not allow wheel(s) of one axle
to spin excessively while the ESC,
ABS, and parking brake warning
lights are displayed. The repairs
would not be covered by the vehi
cle warranty. Reduce engine
power and do not spin the wheel(s)
excessively while these lights are
displayed.
•When operating the vehicle on a
dynamometer, make sure the ESC
is turned off (ESC OFF light illumi
nated).
Information
Turning the ESC off does not affect
ABS or standard brake system operation.NOTICEi
NOTICE
5-39
Driving your vehicle
5
When the ESC is blinking, this
indicates the ESC is active:
Drive slowly and NEVER attempt
to accelerate. NEVER turn the
ESC off while the ESC indicator
light is blinking or you may lose
control of the vehicle resulting in
an accident.
WARNING

6-18
What to do in an emergency
6. Loosen the wheel lug nuts counterclockwise one turn each in the
order shown above, but do not
remove any lug nuts until the tire
has been raised off of the ground. 7. Place the jack at the front (1) or
rear (2) jacking position closest to
the tire you are changing. Place
the jack at the designated loca
tions under the frame. The jacking
positions are plates welded to the
frame with two tabs and a raised
dot to index with the jack.
OGC064005OGS065004
Jack location
To reduce the possibility of injury,
be sure to use only the jack pro
vided with the vehicle and in the
correct jack position; never use
any other part of the vehicle for
jack support.
WARNING

7-56
Maintenance
Wheel replacement
When replacing the metal wheels for
any reason, make sure the new
wheels are equivalent to the original
factory units in diameter, rim width
and offset.
Replacing tires
To reduce the chance or serious
or fatal injuries from an accident
caused by tire failure or loss of
vehicle control:
•Replace tires that are worn,
show uneven wear, or are dam
aged. Worn tires can cause loss
of braking effectiveness, steer
ing control, and traction.
•Do not drive your vehicle with
too little or too much pressure in
your tires. This can lead to
uneven wear and tire failure.
•When replacing tires, never mix
radial and biasply tires on the
same car. You must replace all
tires (including the spare) if mov
ing from radial to biasply tires.
(Continued)
(Continued)
WARNING •Using tires and wheel other than
the recommended sizes could
cause unusual handling charac
teristics and poor vehicle con
trol, resulting in a serious acci
dent.
•Wheels that do not meet
HYUNDAI's specifications may
fit poorly and result in damage to
the vehicle or unusual handling
and poor vehicle control.
•The ABS works by comparing
the speed of the wheels. Tire
size can affect wheel speed.
When replacing tires, all 4 tires
must use the same size original
ly supplied with the vehicle.
Using tires of a different size can
cause the ABS (Antilock Brake
System) and ESC (Electronic
Stability Control) to work irregu
larly. (if equipped)
A wheel that is not the correct size
may adversely affect wheel and
bearing life, braking and stopping
abilities, handling characteristics,
ground clearance, bodytotire
clearance, snow chain clearance,
speedometer and odometer cali
bration, headlight aim and bumper
height.
WARNING

7-72
Maintenance
ITEMNameSymbolFuse RatingCircuit Protected
FUSE
POWER
OUTLET POWER
OUTLET
R R20APower Outlet Rear
STARTSTART10APCU/ECU, Inhibitor Switch, Clutch Pedal Assy,Start Relay, Start Inhibitor Relay
SENSORS10AD4FC, D4FB : Fuel HTR Relay, Fuel Water Sensor
ENGE10AAirflow Sensor(D4FB), Smart key Control Module, ECU/PCU(G4FC,D4FC,D4FB)
ABS10AABS/ ESC Control Module, Rheostat & ESC Switch, Engine Room Diagnosis Connector
AIRBAG 10AAirbag Control Unit
CLUSTERCLUSTER10AInstrument Cluster
* G4FC : Gamma 1.6 (Gasoline), D4FC : UII 1.4 (Diesel), D4FB : UII 1.6 (Diesel)

7-75
7
Maintenance
Engine Compartment Fuse Panel
ItemNameSymbolFuse RatingCircuit Protected
MULTIFUSEMDPS80AMDPS(Motor Power Steering)
ALTALT125A/150AG4FC (125A): Alternator, Battery, All Fuses connected to Alternator fuse
D4FC/D4FB (150A): Alternator, Battery, All Fuses connected to Alternator fuse
FUSE
ECU 2E210A/15AG4FC(10A): ECU (M/T), PCU(A/T)
D4FC(15A): CAM SNSR, Glow RLY, WGT,EGR Control Valve, Air Flow SNSR, IMMO
D4FB (15A): CAM SNSR, VGT Vacuum, IMMO
HEAD LAMPHIGH BEAM10AHead Lamp High Solenoid Relay (BiFunctional Type)
ABS 240AABS / ESC Control Module
ECU 4E425A/15AG4FC(25A): ECU (M/T), PCU(A/T)
D4FC(15A): Inlet Meter Valve,
D4FB(15A): Glow Plug Relay, Fuel Meter Unit
TCU 1625AD4FB: TCU(A/T)
B+540AInstrument Panel Fuse Block Fuse: FS01
ABS 140AABS / ESC Control Module, Engine Room Diagnosis
B+450AInstrument Panel Fuse Block Fuse: FS06, IPS1, IPS2, IPS3
* G4FC : Gamma 1.6 (Gasoline), D4FC : UII 1.4 (Diesel), D4FB : UII 1.6 (Diesel)

7-80
Maintenance
Headlight (Low/High)
1. Open the hood.
2. Remove the headlight bulb cover by turning it counterclockwise.
3. Disconnect the headlight bulb socketconnector.
4. Unsnap the headlight bulb retain ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head light assembly. 6. Install a new headlight bulb and
snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Turn signal light
1. Remove the turn signal light bulbcover by turning it counterclock
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
OGS075050
Turn signal lightParking
(Position) light
Headlight

7-81
7
Maintenance
Parking (Position) light
1. Remove the socket from the
assembly by pulling it straight out.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb by inserting it into the socket.
4. Install the socket in the assembly by pushing it in.
Front fog light bulb replacement
1. Remove the under cover by rotating the screws and bolts.
2. Reach your hand into the back of the front bumper.
3. Disconnect the power connector from the socket.
4. Remove the bulbsocket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5. Install the new bulbsocket into the housing by aligning the tabs on
the socket with the slots in the
housing. Push the socket into the
housing and turn the socket clock
wise.
6. Connect the power connector to the socket.
7. Reinstall the front bumper under cover.
Type B
(1) Headlight (Low/High)
(2) Parking (Position) light
(3) Front turn signal light
(4) Static bending light
(5) Front fog light (if equipped)
(6) Daytime running light (if equipped)
OGS075055