2016 Hyundai Creta light

4.Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5.Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
6.Insert a new bulb into the socket.
7.Install the socket into the assembly by aligning the tabs on the socket
with the slots on the assembly and
turning the socket clockwise.Rear fog lamp (if equipped)
1.Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
2.Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
3.Insert a new bulb in the socket.
4.Reinstall the light assembly to the body of the vehicle.
High mounted stop light
If the light does not operate, we rec
ommend that the vehicle be checked
by an authorized HYUNDAI dealer.
7-86
Maintenance
OGC074031

License plate light bulb replace
ment
1.Remove the tailgate trim.
2.Remove the socket by turning itcounterclockwise.
3.Remove the bulb by pulling it straight out. 4.Install a new bulb.
5.Install the socket by turning it
clockwise.
6.Install the tailgate trim.
7-87
7
Maintenance
OGS075057
OGS075058

Interior light bulb replacement1. Using a flatblade screwdriver,gently pry the lens from the interi
or lamp housing.
2. Remove the bulb by pulling it straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior lamp housing notches and snap
the lens into place.
Use care not to dirty or damage lens,
lens tab, and plastic housings.
NOTICE
7-88
Maintenance
Prior to working on the Interior
lamps, ensure that the “OFF” but
ton is depressed to avoid burning
your fingers or receiving an elec
tric shock.
WARNING
■Map lamp (if equipped)
■Room lampOGS075047/OGS075049/OGS075048
■Luggage room lamp

7-89
7
Maintenance
APPEARANCE CARE
Exterior care
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning
and caution statements that appear
on the label.
Finish maintenance
Washing
To help protect your vehicle’s finish
from rust and deterioration, wash it
thoroughly and frequently at least
once a month with lukewarm or cold
water.
If you use your vehicle for offroad
driving, you should wash it after each
offroad trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign
materials. Make sure the drain holes
in the lower edges of the doors and
rocker panels are kept clear andclean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar
deposits can damage your vehicle’s
finish if not removed immediately.
Even prompt washing with plain
water may not completely remove all
these deposits. A mild soap, safe for
use on painted surfaces, may beused.
After washing, rinse the vehicle thor
oughly with lukewarm or cold water.
Do not allow soap to dry on the finish. •Do not use strong soap, chemical
detergents or hot water, and do not
wash the vehicle in direct sunlight
or when the body of the vehicle is
warm.
•Be careful when washing the side
windows of your vehicle.
Especially, with highpressure
water, water may leak through the
windows and wet the interior.
•To prevent damage to the plastic
parts and lamps, do not clean with
chemical solvents or strong deter
gents.
NOTICE
Wet brakes
After washing the vehicle, test the
brakes while driving slowly to see if
they have been affected by water. If
braking performance is impaired,
dry the brakes by applying them
lightly while maintaining a slow for
ward speed.
WARNING

7-91
7
Maintenance
Brightmetal maintenance
• To remove road tar and insects,use a tar remover, not a scraper or
other sharp object.
• To protect the surfaces of bright metal parts from corrosion, apply a
coating of wax or chrome preser
vative and rub to a high luster.
• During winter weather or in coastal areas, cover the bright metal parts
with a heavier coating of wax or
preservative. If necessary, coat the
par ts with noncorrosive gasoli
neeum jelly or other protective
compound.
Underbody maintenance
Corrosive materials used for ice and
snow removal and dust control may
collect on the underbody. If these
materials are not removed, acceler
ated rusting can occur on the under
body parts such as the fuel lines,
frame, floor pan and exhaust system,
even though they have been treated
with rust protection.
Thoroughly flush the vehicle under
body and wheel openings with luke
warm or cold water once a month,
after offroad driving and at the end
of each winter. Pay special attention
to these areas because it is difficult
to see all the mud and dirt. It will do
more harm than good to wet down
the road grime without removing it.
The lower edges of the doors, rocker
panels, and frame members have
drain holes that should not clog with
dirt; trapped water in these areas can
cause rusting.
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by
water. If braking performance is
impaired, dry the brakes by apply
ing them lightly while maintaining
a slow forward speed.
WARNING

bulb wattaGE
8-3
8
Specifications & Consumer information
* : If equipped
Light BulbWattage (W)
Front Headlight
Type A 60/55
Type B 60
Turn signal light 21
Position light Type A 5
Type B LED
Static bending light (SBL)* 55
Fog light* 35
Side Repeater light (Outside mirror) Type A 5
Type B LED
Daytime running light*21/5
Rear Rear combination light Stop/Tail 21/5
Tail 21/5
Turn signal 21
Back up 16
High mounted stop light 5
License plate light 5
Fog light*21
Interior Map lamp
8
Room lamp 8
Sunvisor lamp5
Luggage room lamp 8