2016 HONDA ACCORD wheel torque

108 || 109
DRIVING
DRIVING
During Operation
If a vehicle is detected ahead of you when ACC is turned on, the system maintains, 
accelerates, or decelerates your vehicle’s set speed to keep the vehicle’s set
following interval from the vehicle ahead.
You can temporarily increase the vehicle speed
when you press the accelerator pedal. ACC stays
on unless you cancel it. When you release the 
accelerator pedal, the system resumes the set
speed or a sufficient speed to maintain the following
interval.
If a vehicle detected ahead of you slows down 
abruptly, or if another vehicle cuts in front of you, 
a beep sounds and BRAKE appears on the multi-
information display to alert you.
ACC has limited braking capability. 
When your vehicle speed drops below 22 mph (35 km/h), ACC will 
automatically cancel and no longer will apply your vehicle’s brakes. 
Always be prepared to apply the brake pedal when conditions require. 
WARNING
Canceling ACC
Press the CANCEL or MAIN button, or press the brake 
pedal. The ACC indicator goes off.
Certain conditions may cause ACC to cancel
automatically. When this happens, the amber ACC 
indicator appears on the multi-information display
(see page 23).
After adaptive cruise control has been canceled, you 
can still resume the prior set speed by pressing RES/+ 
when your vehicle speed is over 25 mph (40 km/h). 
Improper use of ACC can lead to a crash. 
Use ACC only when traveling on open highways in good weather.
WARNING
Beep
Road Departure Mitigation (RDM)*
Alerts and helps to assist you if the system determines a possibility of your vehicle 
unintentionally crossing over detected lane markings while driving between 45–90 
mph (72–145 km/h).
If your vehicle is getting too close to detected lane 
markings without a turn signal activated, a message
appears in the multi-information display. Steering
wheel torque and vibrations are applied to help your 
vehicle stay in the lane.
Braking may also be applied if the lane lines are solid 
and continuous.
If the system operates several times without detecting driver response, the system 
beeps to alert you.
Changing Settings
Determine the warning timing. The vehicle must be in Park (P).
1. Models with one display: Press the SETTINGS 
button. Select Vehicle Settings.
Models with touchscreen: From the HoMe
screen, select Settings. Select vehicle.
2. Select Driver Assist System Setup.
3. Select road Departure Mitigation Setting.
4. Select from the options.
Normal (default): Steering control starts from inside the lane edge.
Wide: Steering control starts from outside the lane edge.
Warning Only: The system only provides a BRAKE message, but does not apply 
steering or braking.
5. Press BACK to exit the menu.
Important Safety Reminder
The RDM system has limitations. Over-reliance on it may result in a collision. It is 
always your responsibility to keep your vehicle within the driving lane.
*if equipped
Beep
Turning the System On or Off
Press the RDM button to turn the system on or off. 
A green indicator appears on the button when the 
system is on.
RDM button
Indicator
Steering assistance

110 || 111
DRIVING
DRIVING
Lane Keeping Assist System (LKAS)*
Provides steering input to help keep the vehicle in the middle of a dete\
cted lane and
visual and tactile alerts if the vehicle is detected drifting out of its\
lane while driving
between 45–90 mph (72–145 km/h).
If your vehicle is getting too close to detected left 
or right side lane markings without a turn signal
activated, the system provides visual and tactile
alerts.
A Lane Departure message appears on the multi-
information display, and the steering wheel vibrates. 
Steering torque is also applied to help keep your 
vehicle within your driving lane. Take appropriate
action to stay within your driving lane.
Turning the System On or Off
1. Press the MAIN button. LKAS appears in the 
multi-information display.
2. Press the LKAS button. Lane outlines appear in 
the multi-information display. Dotted lane lines
turn solid when the system activates.
3. Press the MAIN button or the LKAS button to turn 
the system off.
Important Safety Reminder
LKAS is for your convenience only. It is not a substitute for your vehicle control. The 
system does not work if you take your hands off the steering wheel or fa\
il to steer
the vehicle.
Do not place an object on the top of the instrument panel. It may reflect onto the 
windshield and prevent the system from detecting lane lines properly.
MAIN button
*if equipped
Steering assistance
LKAS button
LaneWatch™*
Check the passenger-side rear areas in the upper display when the right turn signal
is activated.
Activating LaneWatch
Activate the right turn signal. The LaneWatch display 
appears. Check the display for blind spots, and 
visually confirm that it is safe to change lanes.
You can also press the LaneWatch button on the end 
of the turn signal switch to view a constant real-time
display. Press it again to turn the display off.
Changing Settings
Customize the display and how and when the display appears.
1. From the Home screen, select Settings.
2. Select Camera.
3. Select LaneWatch.
4. Select an option and make the preferred changes.
5. Press BACK to exit the menu.
Important Safety Reminder
Like all assistance systems, LaneWatch has limitations. Over-reliance on the system 
may result in a collision.
*if equipped
LaneWatch display
Failure to visually confirm that it is safe to change lanes before doing so may 
result in a crash and serious injury or death.
Do not rely only on LaneWatch while driving. Always look in your mirrors, to 
either side of your vehicle, and behind you for other vehicles before changing 
lanes.
WARNING