2016 FORD MUSTANG start stop button

3
Service Engine
Soon Light
Lights briefly when you switch
the ignition on. If it remains on
or is blinking after you start the
engine, the On-Board Diagnostics
(OBD-II) system has detected a
problem. Drive in a moderate
fashion (avoid heavy acceleration
and deceleration) and contact
an authorized dealer as soon
as possible.
4 Information Display
Provides information about
various systems on your vehicle.
Use the left-hand, 5-way controls
located on the steering wheel
to choose and confirm settings
and messages. Refer to the
Information Displays chapter
of your Owner’s Manual for
more information.
5
Steering Wheel
Media Controls
Press VOL+ or VOL– to increase or
decrease volume levels.
Press
or to access the previous
or next radio station, CD track or
preset satellite radio channel. Press
M repeatedly to access all
possible media sources.
Press
to access SYNC® voice
recognition*.
Press
to access SYNC phone
features or to answer a call.
Press
to end a call.
6 Push-button Switch
Allows you to start your vehicle

by pressing the START STOP
button while fully pressing down
on the brake pedal (with automatic
transmission) or the clutch
(with manual transmission). If
your vehicle has been idling for
an extended period of time, it
automatically shuts down. Before
the engine shuts down, a message
appears in the information
display, allowing the driver to
override the shutdown feature.
Press the button again to switch
the engine off.
Note: Your keyless remote must
be inside the vehicle to switch the
ignition on and start your vehicle.
The keyless warning alert sounds
the horn twice when you exit the
vehicle with the keyless remote
while your vehicle is running.
2
1
3
4
6
5
1 Cruise Control
To set a cruise control speed:
A. Press and release the ON button.
B. Drive to your desired speed, and then press and release
the SET+ button.
C. Take your foot off the accelerator pedal.
To change your set speed, press and release SET+ or SET–.
To cancel your set speed, press and release CNCL or tap the
brake pedal.
To resume a set speed, press and release RES.
To turn cruise control off, press and release OFF.
For information regarding adaptive cruise control*, see the
Cruise Control chapter in your Owner’s Manual.
2 Lighting Control
Switches off the headlamps.

Switches on the parking, instrument panel, license
plate and tail lamps.
Switches on the headlamps.
Autolamps* automatically switch the exterior lamps
on or off based on available daylight.

Switch the fog lamps* on or off by pressing
the control.
INSTRUMENT PANEL
4
5*if equipped*if equipped

Climate
SYNC 3 controls the temperature,
airflow direction, fan speed, and
activates other climate features, like
the heated steering wheel.* Use the
touchscreen to enter into each feature’s
submenu for additional options.
Set Your Temperature
» Touch the climate icon on your
touchscreen.
» Set your exact, desired temperature
using the
▲ or ▼ buttons.
Audio
No matter how you store your music,
SYNC makes it yours to enjoy when
you’re behind the wheel. Just press the
audio icon on the touchscreen. From
here, you can easily go between AM,
FM, Sirius, Bluetooth Stereo, Apps and
other media sources.
Set Your Radio Presets
» Touch the Audio icon > FM >
Direct Tune.
» Type in the frequency of your
desired station, and then select
Enter. You can also use the tune or
seek controls on the radio bezel or
the controls on the steering wheel
to select a station.
» Touch and hold one of the memory
preset buttons to save your station.
Bring in Your Own Music
Plug USB devices into your USB ports,
and use SYNC to play all of your favorite
music. After you plug your device into
a USB port, select Sources and then
choose USB. You can use the Shuffle
function to create random playlists.
Apps
Stream Apps
The system supports the use of
certain apps such as Pandora
® or
iHeartRadio® through a USB or
Bluetooth-enabled devices.
Each app gives you different on-screen
options depending on the app’s content.
Refer to your SYNC Supplement for
more information.
SYN C® 3* (CONTINUED)
Power Lumbar*
The power lumbar control is located on
the side of the driver seat.
Press one side of the control to increase
lower back firmness. Press the other
side of the control to decrease lower
back firmness.
Climate Controlled
Front Seats*
Touch the heated seat symbol
to cycle through the various heat
settings and off. More lights indicate
warmer settings.
Press the cooled seat symbol
to
cycle through the various cooling
settings and off. More lights indicate
cooler settings.
Dual-zone Automatic
Temperature Control*
To use, press the AUTO control and
then select the desired temperature by
using the control. Set an independent
temperature for the front-seat
passenger by using the passenger-side
rotary control.
Press and hold the AUTO control
to switch back to a single-zone
temperature control.
Rear Seat Access
Use the seatback release to fold the back
of the front seat forward. This release
handle is on the upper back of the front
seat. The seatback recline feature has
memory and locks automatically in the
original position.
Global Opening
You can use the remote control
to operate the windows with the
ignition off.
You can open the windows for a short
time after you unlock your vehicle
with the remote control. After you
unlock your vehicle, press and hold
the remote control unlock button to
open the windows. Release the button
once movement starts. Press the lock or
unlock button to stop movement.
Note: You can enable or disable this
feature in the information display, or
see an authorized dealer. To operate
this feature, you must deactivate the
accessory delay.
COMFORT
10
*if equipped
11
*if equipped

Rear Parking Aid*
The rear sensors are active only when the
transmission is in reverse (R). As your
vehicle moves closer to the obstacle, the
rate of the audible warning increases.
The system detects certain objects while
the transmission is in reverse (R) and the
vehicle is traveling at a speed of 3 mph
(5 km/h) or less.
The system can be switched off through
the information display. See the Parking
Aids chapter of your Owner’s Manual
for details.
Blind Spot
Information System (BLIS®) *
BLIS aids you in detecting vehicles that
may have entered the blind spot zone.
The detection area is on both sides of
the vehicle, extending rearward from
the exterior mirrors to approximately
13 feet (4 meters) beyond the bumper.
The system alerts you if certain vehicles
enter the blind spot zone while driving.
See the Driving Aids chapter of your
Owner’s Manual for details.
Cross Traffic Alert*
Cross traffic alert warns you of vehicles
approaching from the sides when the
transmission is in reverse (R). The system
illuminates an amber alert indicator in
the outside mirror on the side of your
vehicle the approaching vehicle is coming
from. Cross Traffic Alert also sounds an
audible alert and a message appears in the
information display indicating a vehicle
is coming from the right or left. This
system also works with the reverse sensing
system that sounds its own series of tones.
See the Driving Aids chapter of your
Owner’s Manual for details.
Note: Visibility aids do not replace
the need to watch where the vehicle is
moving. Refer to the Owner’s Manual
for safety information, more details and
system limitations.
FUNCTION(CONTINUED)
Collision Warning System*
This system is designed to alert you of certain collision risks.
A radar detects if your vehicle is rapidly approaching another
vehicle traveling in the same direction as yours. If it is, a
red warning light illuminates and an audible warning
chime sounds.
The brake support system assists the driver in reducing the
collision speed by charging the brakes. If the risk of collision
further increases after the warning light illuminates, the
brake support prepares the brake system for rapid braking.
This may be apparent to the driver. The system does not
automatically activate the brakes, but if the driver presses the
brake pedal, full force braking is applied even if the driver
lightly presses the brake pedal.
You can adjust the warning system sensitivity to one of three
possible settings through the information display control.
See the Driving Aids chapter in your Owner’s Manual
for details.
Traction Control
The system automatically turns on each time you switch the
ignition on. If your vehicle is stuck in mud or snow, switching
traction control off may be beneficial as this allows the wheels
to spin.
The switch for the stability and traction control system is on
the instrument panel. When you switch the system off, a message and an illuminated
icon appear on the instrument cluster.
Use the switch again to return the traction control system to
normal operation.
Note: When you switch traction control off, stability control
remains fully active.
AdvanceTrac™
The system automatically activates when you start your
engine. The electronic stability control portion of the

system disables when the transmission is in reverse (R),
or on some models, if you press and hold the stability control
button for more than five seconds when you apply the
brakes and the vehicle is at a stop. You can switch off the
traction control portion of the system independently. See
the Stability Control chapter of your Owner’s Manual
for details.
Pony Projection Lights*
The lights are on the bottom of the mirror housings.
This feature projects an image onto the ground a short
distance from the vehicle with the illuminated entry and
exit feature.
FUNCTION(CONTINUED)
16 17*if equipped*if equipped