2016 FIAT FULLBACK keyless entry

VEHICLE CHANGES / ALTERATIONS
IMPORTANT
Any change or alteration of the vehicle might seriously affect its safety and road holding, thus causing accidents, in which the
occupants could even be fatally injured.
ACCESSORIES PURCHASED BY THE OWNER
If after buying the vehicle, you decide to install electrical accessories that require a permanent electrical supply (e.g. radio,
satellite anti-theft system, etc.) or accessories that in any case burden the electrical supply, contact a Fiat Dealership, whose
personnel will check whether the vehicles's electrical system is able to withstand the load required, or whether it needs to be
integrated with a more powerful battery.
IMPORTANT Take care when fitting additional spoilers, alloy wheels or non-standard wheel hubs: they could reduce the
ventilation of the brakes and affect efficiency under sharp, repeated braking or on long descents. Make sure that nothing
obstructs the pedal stroke (mats, etc.).
INSTALLING ELECTRICAL / ELECTRONIC DEVICES
Electrical and electronic devices installed after buying the vehicle in the context of after-sales service must carry the following
label: FCA Italy S.p.A. authorises the installation of transceivers provided that installation is carried out at a specialised
centre, in a workmanlike fashion and in compliance with manufacturer's specifications.
Traffic police may not allow the vehicle on the road if devices have been installed which modify the features of the vehicle. This
may also cause invalidation of warranty in relation to faults caused by the change either directly or indirectly related to it.
FCA Italy S.p.A. shall not be liable for damage caused by the installation of accessories either not supplied or recommended by
FCA Italy S.p.A. and not installed in compliance with the provided instructions.
RADIO TRANSMITTERS AND MOBILE PHONES
Radio transmitter equipment (vehicle mobile phones, CB radios, amateur radio etc.) cannot be used inside the vehicle unless a
separate aerial is mounted externally. Transmission and reception of these devices may be affected by the shielding effect of the
vehicle body. As far as the use of EC-approved mobile phones is concerned (GSM, GPRS, UMTS, LTE), follow the usage
instructions provided by the mobile phone Manufacturer. The use of these devices inside the passenger compartment (without
an external aerial) may cause the electrical systems to malfunction. This could compromise the safety of the vehicle in addition
to constituting a potential hazard for passengers' health. If mobile phones/laptops/smartphones/tablets are inside the vehicle
and/or close to the electronic key, a reduced performance of the Passive Entry/Keyless Entry-N-Go system may occur.
5

KEYS
1. Master key 2. Master key (plate)
3. Keyless entry key 4. Keyless
operation key 5. Emergency key
1)
NOTE The key is a precision electronic
part with a built-in signal transmitter.
Please observe the following in order to
prevent a malfunction.
Do not leave anywhere that is
exposed to direct sunlight, for example
on the dashboard.
Do not disassemble or modify.
Do not excessively bend the key or
subject it to a strong impact.
Do not expose to water.
Keep away from magnetic key rings.
Keep away from audio systems,
personal computers, TVs, and any
other equipment that generates amagnetic field.
Keep away from devices that emit
strong electromagnetic waves, such as
cellular phones, wireless devices and
high frequency equipment (including
medical devices).
Do not wash with ultrasonic cleaners
or similar equipment.
Do not leave the key where it may be
exposed to high temperature or high
humidity.
NOTE The engine is designed so that it
will not start if the ID code registered in
the immobilizer computer and the key’s
ID code do not match. Refer to the
section entitled “Electronic immobilizer”
for details and key usage.
KEY NUMBER TAG
The key number is stamped on the tag
as indicated in the illustration. Make a
record of the key number and store the
key and key number tag in separate
places, so that you can order a key
from your Fiat Dealership in the event
the original keys are lost.
ELECTRONIC
IMMOBILIZER
(where provided)
2)
The electronic immobilizer is designed
to reduce significantly the possibility of
vehicle theft. The purpose of the system
is to immobilize the vehicle if an invalid
start is attempted. A valid start attempt
can only be achieved, using a key
“registered” to the immobilizer system.
1
45
2
3
4AH3100320
5AA0109480
13

Vehicles without keyless operation
system
In the following cases, the vehicle may
not be able to receive the registered ID
code from the registered key and
engine may not start.
When the key contacts a key ring or
other metallic or magnetic object
When the key grip contacts metal of
another key
When the key contacts or is close to
other immobilizing keys (including keys
of other vehicles) In cases like these,
remove the object or additional key
from the vehicle key. Then try again to
start the engine. If the engine does not
start, we recommend you to contact a
Fiat Dealership.
NOTE If you lose one of the master
keys, the keyless entry keys or the
keyless operation keys, contact a Fiat
Dealership as soon as possible. Refer
to “Keys”. To obtain a key, take your
vehicle and all remaining keys to a Fiat
Dealership. If you need an extra spare
key, take your vehicle and all the keys
to a Fiat Dealership. All the keys have to
be re-registered in the immobilizer
computer unit. For further information,
please contact a Fiat Dealership.
KEYLESS ENTRY SYSTEM
Press the key switch to lock or unlock
the doors. It is also possible to operate
the outside rearview mirrors. (Vehicles
equipped with the mirror retractor
switch).
1. LOCK switch 2. UNLOCK switch
3. Indicator lamp
To lock
Press the LOCK switch (1). All the
doors will be locked. The turn-signal
lamps will blink once. When they are
locked with the room lamp switch in the
middle (●) position, the room lamp also
blink once.
To unlock
Press the UNLOCK switch (2). All the
doors will be unlocked. If the room
lamp switch is in the middle (●) position
at this time, the room lamp will come on
for approximately 15 seconds and theturn-signal lamps will blink twice.
NOTE For vehicles equipped with the
mirror retractor switch, the outside
rear-view mirrors automatically retract
or extend when all the doors are locked
or unlocked using the key switches of
the keyless entry system. Refer to
“Starting and driving: Outside rear-view
mirrors”.
NOTE If the UNLOCK switch (2) is
pressed and no door is opened within
approximately 30 seconds, relocking
will automatically occur.
It is possible to modify functions as
follows: For further information, please
contact a Fiat Dealership.
The time from pressing of the
UNLOCK switch (2) to the moment of
automatic locking can be changed.
Activating the operation confirmation
function (blinking of the turn-signal
lamps) only during locking, or only
during unlocking.
The confirmation function (this
indicates locking or unlocking of the
doors with the blink of the turn-signal
lamps) can be deactivated.
The number of times the turn-signal
lamps are blinked by the confirmation
function can be changed.
On vehicles with keyless operation
system, the buzzer sound can be
activated when a keyless operation is
done.
13
2213
6AHA101774
14
GETTING TO KNOW YOUR VEHICLE

Operation of the outside rearview
mirrors (Vehicles equipped with the
mirror retractor switch)
To fold — Locking the doors using the
LOCK switch (1), the outside rear-view
mirrors are folded automatically.
To extend — Unlocking the doors using
the UNLOCK switch (2), the outside
rear-view mirrors are extended
automatically.
Functions can be modified as stated
below. Please consult a Fiat Dealership.
Automatically extend when the
driver’s door is closed, and then the
following operation is performed.
Except for vehicles equipped with the
keyless operation system: turn the
ignition switch to the “ON” or “ACC”
position. Vehicles equipped with the
keyless operation system: put the
operation mode in ON or ACC
Automatically retract when the
ignition switch is turned to the “LOCK”
position or the operation mode is put in
OFF, and the driver’s door is then
opened.
Automatically extend when the
vehicle speed reaches 30 km/h.
Deactivate the automatic extension
function.The keyless entry system does not
operate in the following conditions:
The key is left in the ignition switch
(except for vehicles with keyless
operation system).
The operation mode is not in OFF
(vehicles with keyless operation
system).
The door is open.
NOTE The key switch will operate
within approximately4mfromthe
vehicle. However, the operating range
of the key switch may change if the
vehicle is located near a TV transmitting
tower, power station, or radio
broadcasting station.
If either of the following problems
occurs, the battery may be exhausted.
The key switch is operated at the
correct distance from the vehicle, but
the doors are not locked/unlocked in
response.
The indicator lamp (3) is dim or does
not come on. For further information,
please contact a Fiat Dealership. If you
replace the battery yourself, refer to
“Procedure for replacing key battery”.
NOTE If your key is lost or damaged,
please contact a Fiat Dealership for a
replacement key.
NOTE If you wish to add key, please
contact a Fiat Dealership. The following
numbers of the keys are available:
Keyless entry key: up to 4 keys
Keyless operation key: up to 4 keys.
Procedure for replacing the key
battery
1)
3)
Before replacing the battery, remove
static electricity from your body by
touching a metal grounded object.
NOTE You may purchase a
replacement battery at an electric
appliance store.
NOTE Fiat Dealership can replace the
battery for you if you prefer.
Keyless entry key
1. Remove the screw (A) from the key.
2. With the Fiat mark facing you, insert
the cloth-covered tip of a straight blade
(or minus) screwdriver into the notch in
the key case and use it to open the
case.
A
7AA0092878
15

NOTE Be sure to perform the
procedure with the Fiat mark facing
you. If the Fiat mark is not facing you
when you open the key case, the
switches may come out.
3. Remove the transmitter (B) from the
key case. Then, open the transmitter (B)
using the method described in step 2.
4. Remove the old battery.5. Install a new battery (CR1616) with
the + side (C) down.
6. Close the transmitter firmly.
7. Place the transmitter in the key case,
then securely close the case.
8. Attach the screw (A) removed in step
1.
9. Check the keyless entry system to
see that it works.
Keyless operation key
1. With the Fiat mark facing you, insert
the cloth-covered tip of a straight blade
(or minus) screwdriver into the notch in
the key case and use it to open the
case.
NOTE Be sure to perform the
procedure with the Fiat mark facing
you. If the Fiat mark is not facing you
when you open the key case, the
transmitter may come out.2. Remove the old battery.
3. Install a new battery (CR2032) with
the + side (A) up.
4. Close the key firmly.
5. Check the keyless operation function
to see that it works.
8AA0092881
B
9AHA105378
C
10AHA105381
11AF0006861
A
12AF0006858
16
GETTING TO KNOW YOUR VEHICLE

KEYLESS OPERATION
SYSTEM
The keyless operation system allows
you to lock and unlock the doors, start
the engine and change the operation
mode simply by carrying the keyless
operation key with you.
The switches on the keyless operation
key can also be used as the key switch
of keyless entry system. Refer to
“Starting and stopping the engine”.
Refer to “Keyless entry system”. The
driver should always carry the keyless
operation key. This key is necessary for
locking and unlocking the doors,
starting the engine and otherwise
operating the vehicle, so before locking
and leaving the vehicle, be sure to
check that you have the keyless
operation key.
4) 5)
You can limit the possible operations of
the keyless operation system. Please
consult a Fiat Dealership.
The keyless operation key uses an
ultra-weak electromagnetic wave. In the
following cases, the keyless operation
system may not operate properly or
may be unstable.
When there is equipment nearby that
emits strong radio waves, such as: a
power station, a radio/TV broadcasting
station or an airport.
The keyless operation system is
carried together with a communicationsdevice such as a cellular phone or radio
set, or with an electronic device such as
a personal computer.
The keyless operation key is touching
or covered by a metal object.
A keyless entry system is being used
nearby.
When the keyless operation key
battery is worn out.
When the keyless operation key is
set down in an area with strong radio
waves or noise. In such cases, use the
emergency key. Refer to “To
lock/unlock without using the keyless
operation function”.
NOTE Because the keyless operation
key receives signals in order to
communicate with the transmitters in
the vehicle, the battery continually
wears down regardless of keyless
operation key use. The battery life is
1 to 2 years, depending on usage
conditions. When the battery wears out,
replace the battery according to the
description in this manual or have it
replaced a Fiat Dealership. Refer to
“Procedure for replacing the key
battery”.
NOTE Because the keyless operation
key continually receives signals, strong
radio wave reception could affect
battery wear. Do not leave the key near
a TV, personal computer, or other
electronic device.Operating range of the keyless
operation system
If you are carrying the keyless operation
key, enter the operating range of the
keyless operation system, and press
the driver’s or front passenger’s door
lock/unlock switch, the ID code for your
key is verified.
You can lock and unlock the doors,
start the engine and change the
operation mode only if the ID codes of
your keyless operation key and the
vehicle match.
NOTE If the keyless operation key
battery is wearing out or there are
strong electromagnetic waves or noise
present, the operating range may
become smaller and operation may
become unstable.
Operating range for locking and
unlocking the doors
The operating range is approximately
70 cm from the driver’s or front
passenger’s door lock/unlock switch.
NOTE Locking and unlocking operate
only when you press a door switch that
detects the keyless operation key.
NOTE Operation may not be possible if
you are too close to the front door, door
window.
NOTE Even if the keyless operation key
is within 70 cm of the driver’s or front
passenger’s door lock/unlock switch, if
the key is near to the ground or high
up, the system may not operate.
17

ACC power auto-cutout function
After about 30 minutes has elapsed
with the operation mode in ACC, the
function automatically cuts out the
power for the audio system and other
electric devices that can be operated
with that position. (only that driver’s
door has closed and the selector lever
in the “P” (PARK) position).
When you open driver’s door or the
engine switch operate again, the power
is supplied again.
NOTE When ACC power supply
automatic stop, the steering wheel
can’t lock and you can’t lock and
unlock the doors by the keyless entry
key and keyless operation key.
NOTE It is possible to modify functions
as follows:
The time until the power cuts out can
be changed to about 60 minutes.
The ACC power auto-cutout function
can be deactivated. For details, we
recommend you to consult a Fiat
Dealership.
Operation mode OFF reminder
system
When the operation mode is in any
mode other than OFF, if you close all
the doors then try to lock the doors by
pressing the driver’s or front
passenger’s door lock/unlock switch, a
warning lamp will blink and the outer
buzzer will sounds and you cannot lock
the doors.
Operation mode ON reminder
system
If the driver’s door is opened with the
engine stopped and the operation
mode in any mode other than OFF, the
operation mode ON reminder inner
buzzer sounds intermittently to remind
you to put the operation mode in OFF.
WARNING
6)Do not remove the ignition key from the
ignition switch while driving. The steering
wheel will be locked, causing loss of
control.
7)If the ignition device has been tampered
with (e.g. an attempted theft), have it
checked over by a Fiat Dealership before
driving again.
8)Always remove the key when you leave
your vehicle to prevent someone from
accidentally operating the controls.
Remember to engage the handbrake.
Engage first gear if the vehicle is parked
uphill or reverse gear if the vehicle is
parked downhill. Never leave children
unattended in the vehicle.
9)Never extract the key while the vehicle is
moving. The steering wheel will lock as
soon as it is turned. This also applies to
cases in which the vehicle is towed.
10)Under no circumstances should
aftermarket operations be carried out
involving steering system or steering
column modifications (e.g. installation of
anti-theft device). This could negatively
affect performance and safety, invalidate
the warranty, cause serious safety
problems and also result in vehicle
non-compliance with type-approval
requirements.
23AHA103505
25

CENTRAL DOOR LOCKS
(where provided)
Repeated continuous operation
between lock and unlock could activate
the central door locking systems built-in
protection circuit and prevent the
system from operating. If this occurs,
wait approximately 1 minute before
operating the central door lock system.
All of the doors can be locked and
unlocked as described hereafter.
Driver’s door with key (except for
vehicles with keyless operation
system)
Driver’s door with key (except for
vehicles with keyless operation system)
A — Lock
B — UnlockDriver’s door with inside lock knob
Using the door lock knob on the driver’s
door locks or unlocks all doors.
A — Lock
B — Unlock
NOTE Be careful not to lock the doors
while the key is inside the vehicle when
getting off the vehicle.
Using the ignition switch or the
engine switch
On vehicles with the keyless entry
system or the keyless operation
system, it is possible to unlock all of the
doors whenever the ignition switch is
turned to the “LOCK” position or the
operation mode is put in OFF.
NOTE If you wish to change the setting
such that the doors are unlocked,
please contact a Fiat Dealership.Using the selector lever position
(vehicles with A/T)
On vehicles with the keyless entry
system or the keyless operation
system, it is possible to unlock all of the
doors using the selector lever by
placing the selector lever in the “P”
(PARK) position while the ignition switch
or the operation mode is in the “ON”
position.
NOTE If you wish to change the setting
such that the doors are unlocked,
please contact a Fiat Dealership.
BA
28AHA105453
29AHA105466P
30AHA105482
28
GETTING TO KNOW YOUR VEHICLE