2016 Citroen JUMPER length

81
jumper_en_Chap03_Ergo-et-confort_ed01-2015
LOAd SPAcE FIttInGSSupport for stowing rail
Supports for securing a stowing rail are
available above the trims, on each side of
the vehicle.
Maximum load: 200 kg.
12 volt socket
Maximum power: 180 W.Lashing rings
Lashing rings are provided on the floor to
secure and make safe your loads: 8 for L1
and L2 length vehicles, 10 for L3 and L4
length vehicles.
Two additional rings are located on the
partition behind the cab.
Maximum load: 500 kg.
Side trim
The lower parts of the sides are fitted with
load protection trims.
As a safety precaution in case of sharp
braking, you are advised to place
heavy objects as far forwards towards the
cab as possible.
Practical information
3
EASE OF uSE and cOMFOrt

107
jumper_en_Chap05_Securite_ed01-2015
rEAr SEAt BELt S
The rear seats/bench seats are fitted with
three-point seat belts and inertia reels.
The centre seat has a seat belt guide and
inertia reel, solid with the seat back.
A carrier is provided at each outer seat to
allow the seat belt buckle to be secured
when not in use.
Good practice
The driver must ensure that passengers use
the seat belts correctly and that they are all
strapped in securely before moving off.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for short
journeys.
The seat belts are fitted with an inertia reel
which automatically adjusts the length of the
strap to your size.
Do not use accessories (clothes pegs, clips,
safety pins, etc.) which allow the seat belt
straps to fit loosely.
You can unfasten the seat belt by pressing
the red button on the buckle. Guide the seat
belt after unfastening.
Ensure that the seat belt has reeled in
correctly after use.
After folding or moving a seat or a rear
bench seat, ensure that the seat belt has
reeled in correctly and that the buckle is
ready to accommodate the tongue.
The airbag warning lamp also
comes on if the pretensioners are
deployed. Contact a C
i T roën

dealer or a qualified workshop.
In the event of an impact
o
nly for the front seats, and depending on
the nature and seriousness of the impact,
the pretensioning device may be deployed
before and independently of inflation of the
airbags.
i t instantly tightens the seat belts
against the body of the occupants.
Deployment of the pretensioners is
accompanied by a slight discharge of
harmless smoke and a noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system.
The force limiter reduces the pressure of the
seat belt against the body of the occupants.
The pyrotechnic pretensioners are active
when the ignition is switched on and the
seat belt fastened.
The inertia reels are fitted with a device
which automatically locks the strap in the
event of a collision or emergency braking or
if the vehicle rolls over.
Seat belts
5
SAFETY

123
jumper_en_Chap06_Accessoires_ed01-2015
rOOF cArrYIn G SYS t EMS
refer to the "Technical data -
"Dimensions" section for more
information on the length (L1 to L4) and the
height (H1 to H3) of the vehicle. Maximum load on the roof, evenly
distributed: 150 kg, for all versions,
within the vehicle's weight limit (Gross
Vehicle Weight).
For reasons of safety and to avoid damaging
the roof, it is essential to use a carrying
system (roof bars or roof rack) that is
approved for your vehicle.
r

oof bars can only be fitted to an H1 or
H2

height van, combi and minibus versions. o
n a minibus, check for the presence of roof
air conditioning units. The carrying system must always be
secured to the fitting points provided on the
vehicle's roof: 6, 8 or 10, depending on the
wheelbase of the vehicle.
o

bserve the instructions for fitting and use
provided with the carrying system.
o
n all H3 height versions, the roof
cannot be fitted with a carrying system.
o

bserve in full the legal requirements
related to carrying outsized loads.
6
Transport solutions
ACCESSoriES

173
jumper_en_Chap09_Caracteristiques-Techniques_ed01-2015
dIMEnSIOnS
The dimensions are given in millimetres.
This model is available in 4 lengths (L1...) and 3 heights (H1...); refer to the corresponding tables:VA
n
L1L2L3L4
H1 H2 H1 H2 H2 H3 H2 H3
L
o

verall length 4
9635
4135
9986
363
H
o

verall height 2
254 2 524 2 254 2 524 2 524 2 764 2 524 2 764
A Wheelbase 3
0003
4504
035
B Front overhang 948
cr

ear overhang 1
0151
380
dOverall width (incl./excl. mirrors)2 508 / 2

050
E Width of front track 1
810
F Width of rear track 1
790
G Height of load floor 535 to 565
I Length of interior floor 2
6703
1203
7054
070
jMaximum interior load height1

662 1 932 1 662 1 932 1 932 2 172 1 932 2 172
K Maximum interior width 1
870
M
i

nterior width between wheel arches 1
422
Volume (m
3) 89.5 10 11.5 13 15 15 17
9
TECHniCAL DATA
Dimensions

252
jumper_en_Chap11_Particularites_ed01-2015
dIMEnSIOnS
The dimensions are given in millimetres.
cHASSIS cAB
FLOO r c AB
L1 L2L2S L3L4
L
o

verall length 4

908 5

358 5
708 5
9436
208
A Wheelbase 3

000 3

450 3
800 4
0354
035
B Front overhang 948
cr

ear overhang 9601 225
dOverall width (incl./excl. mirrors) 2 508 / 2

050
- Passable width 2
207
- Max permitted body width 2
350
E Front track 1
810
-
r

ear track 1
790
- Width of increased rear track 1
980
F
o

verall height 2
153
- Max permitted body height 3
500
Chassis cab / Floor cab

256
jumper_en_Chap11_Particularites_ed01-2015
dIMEnSIOnS
The dimensions are given in millimetres.
c
HASSIS d O u BLE c AB
FLOO
r d O u BLE c AB
L2 L3L4
L
o

verall length 5 7986 2286 678
A Wheelbase 3 4504 0354 035
B Front overhang 948948948
cr

ear overhang 1 2451 3401 695
dWidth (with / without mirrors) 2 508 / 2 1002 508 / 2 1002 508 / 2 100
E Front track 1 8101 8101 810
-
r

ear track 1 7901 7901 790
F
o

verall height 2 4242 4242 424
Double cab

261
jumper_en_Chap11_Particularites_ed01-2015
tipper (in mm)
Load length 3 200
o

verall length 3
248
Load width 2 000
o

verall width 2 100
Height of body sides 350
o

verall height 550
dIMEnSIOnS
This conversion is only available on the L2 single chassis-cab; refer to\
the table below for the characteristics of the tipper.
For information on the characteristics of the L2 chassis cab, refer to t\
he "Dimensions" section for the floor cab version.
SPECiAL FEATUrES
Tipper body