2016 Citroen JUMPER ECU

152
jumper_en_Chap08_Aide-rapide_ed01-2015
courtesy lamps
type c , 12 V 10 W - 10 W
-
Press at the points indicated by the

arrows, then remove the courtesy lamp.
-
o pen the protective flap.
-

Change the bulb moving aside the two

contacts.
-

Ensure that the new bulbs are secured

correctly between the two contacts.
-

Close the protective flap.
-


Fix the courtesy lamp in its housing and

ensure that it is secured correctly.
Side marker lamps
type A , W5W - 5W
- i f your vehicle is fitted with these lamps
(L4 body), remove the two fixing screws.
-

Pull the bulb holder to release it from the

lugs.
-

Pull the bulb out and change it.
direction indicator side
repeaters
type A , W 16 W F - 16 W
-
Move the mirror glass to access the

screws.
-
r emove the two fixing screws.
-

Pull the bulb holder to release it from the

lugs.
-

Pull the bulb out and change it. Front /

r ear
Failed bulb or lamp

154
jumper_en_Chap08_Aide-rapide_ed01-2015
third brake lamp
type A, W5W - 5W (x 4)
- r emove the two lamp fixing screws.
-
r emove the lamp by pulling it towards
you.
number plate lamps
type c , C5W - 5W
-
Press the point, indicated by the arrow
,
then remove the plastic lens.
-
r emove the failed bulb by moving aside
the two contacts.
-

With the new bulb in place, ensure that

it is secured correctly between the two
contacts.
-
r eplace the plastic lens and press on it
to lock it in place. -
r emove the bulb holder by squeezing
the two tabs.
- r emove the failed bulb by pulling it out.
-

Change the bulb.
Failed bulb or lamp

155
jumper_en_Chap08_Aide-rapide_ed01-2015
cHAnGInG A WIPE r BLA d E
The steps, located in the front bumper,
enable you to reach the blades and the
screenwash jets.changing a front wiper blade
raise the wiper arm.
Unclip the blade by pressing the button and
remove it by pulling it outwards.
Fit the new blade and ensure that it is
secured correctly.
r

eturn the wiper arm to the normal position.
Check that the screenwash or
headlamp wash jets are not blocked.
Worn wiper blade
QUiCK HELP
8

156
jumper_en_Chap08_Aide-rapide_ed01-2015
Parking the vehicle
Where possible, park the vehicle on level,
stable and non-slippery ground.
Apply the parking brake, switch off the
ignition and engage first gear.
Wear a high visibility vest and position the
warning triangle on the road.
You must ensure that the occupants get out
of the vehicle and wait in a safe location.
tools
These are stowed in a box located under the
front passenger seat.
-
T
urn the button a quarter of a turn then
pull the box.
-

After use, press the button then turn it a

quarter of a turn to secure the box.
A.

Long socket.
B.

Bar.
c

. Jack.
d

. Wheelbrace.
E.

Screwdriver (handle and bits).
F.


r emovable towing eye.
cHAnGInG A WHEELPneumatic suspension
i
f you vehicle is fitted with this system, you
must first activate vehicle lifting mode.
Press the two controls simultaneously for at
least 5 seconds; their indicator lamps come
on.
This mode is deactivated automatically after
changing a wheel, once the speed of the
vehicle has exceeded 3 mph (5 km/h).
The jack and the tool kit are specific to


your vehicle. Do not use them for other
purposes.
n

ever go underneath a vehicle supported
only by a jack (use an axle stand).
Puncture

159
jumper_en_Chap08_Aide-rapide_ed01-2015
Fitting the spare wheelStowing the wheel
- Put the spare wheel in place on the hub
and fit the bolts by hand.
-

Pre-tighen the bolts using the

wheelbrace
d and the bar

B.
-

Lower the vehicle completely by folding

the jack
c
, then remove the jack.
-


T
ighten the bolts again using the
wheelbrace
d and the bar

B (tighten
them fully without forcing them). You must place the wheel to be repaired or
the spare wheel under the vehicle to secure
the carrier system.
-

Place the wheel at the rear of the vehicle.
●


For eversions with
steel wheels, hook
the carrier H on the outside.
●

Screw in the grip
G to secure the carrier
and wheel. ●
For versions with alloy wheels, position
the strap j
on the outside.
●


Fit the three strap fixing screws
I to the
alloy wheel.
Puncture
QUiCK HELP
8

160
jumper_en_Chap08_Aide-rapide_ed01-2015
refer to the "Technical data -
i
dentification markings" section for the
location of the tyre pressure label.
-
Fit the long socket
A
, the wheelbrace
d

and bar B to the securing screw.
-

T

urn the assembly clockwise to fully
draw in the cable and raise the wheel
under the vehicle.
-

Check that the wheel is positioned


horizontally flat against the floor of the
vehicle and that the the cut-out for the
carrier system is visible.
-

Stow the tools and the trim (depending


on version).
refitting the repaired wheel
refitting the repaired wheel is the same as
fitting the spare wheel; don't forget to refit
the wheel trim.
The spare wheel is not designed to be used
over long distances. Have the tightening of
the bolts and pressure of the spare wheel
checked by a C
i T roën dealer or a qualified
workshop without delay.
Also, have the original wheel repaired and
refitted by a C
i T roën dealer or a qualified
workshop as soon as possible.
Puncture

249
jumper_en_Chap11_Particularites_ed01-2015
PrESEntAtIO n
The crew cab is available on van versions and comprises a bench seat, se\
at belts, a storage
space and side windows.
i

t is separated from the load space and a high-strength partition offering comfort and safety.
rear bench seat
This ergonomic bench seats four people.
Storage space
A storage space is provided under the bench
seat.
From the cab, tilt the seat cushion forward
for access to it
Good practice
Do not tilt the bench seat cushion during
transportation.
n
o not attach anything to the cab fixing
structure.
Do not exceed the number of passengers
indicated on the registration certificate.
i

n the rear, the load space is intended for
carrying goods only.
You are advised to place the goods or heavy
objects as far forwards as possible in the
load space (towards the cab) and secure
them by means of straps using the stowing
rings on the floor.
SPECiAL FEATUrES
Crew cab

250
jumper_en_Chap11_Particularites_ed01-2015
Sliding side windows
Depending on the vehicle's equipment, the
side windows of row 2 can be opened.
Squeeze the two controls then slide the
window.
While driving, the window must be

closed or secured in an intermediate
position.
Do not extend long objects outside the
vehicle via the window.
Seat belts
Each rear seat is fitted with a three-point
inertia reel seat belt.
Fastening
Pull the strap in front of you, with an even
movement, ensuring that it does not twist.
Secure the buckle in its housing.
Check that the seat belt is fastened securely
and that the automatic locking system is
operating correctly by pulling the strap
rapidly.
u
nfastening
Press the red button on the buckle housing,
the seat belt rolls up automatically but you
are advised to guide it.
Use the seat belt to restrain one person
only per seat.
child seats
Do not install child seats, booster
cushions or carrycots on the rear seats
of the cab.
Crew cab