2016 Citroen DS5 HYBRID Owner's Manual

11Hybrid4 system













On starting and when stationary

There is no flow of energy; the Stop & Start alternator-starter
stops and restarts the HDi Diesel engine automatically,
whatever the operating mode selected.


Energy recovery

During this phase (deceleration, braking, foot off the
accelerator, … all modes), the high voltage battery is
recharged by the electric motor/generator, then being driven by
the rear wheels.
You can maximise this energy recovery by taking your foot off
the accelerator pedal; deceleration will be less marked than
with a conventional vehicle.


100% electric

In all electric running (AUTO or ZEV modes), only the electric
motor drives the vehicle, via the rear wheels, powered by the
high voltage battery.
The display of " Zero Emission
" indicates that the HDi Diesel
engine is stopped and the vehicle is producing no CO
2.

Fuel consumption histogram
(Only with touch screen)


This graph represents the history of average fuel
consumption figures.
It is accessible via the " Driving
" menu of the touch
screen.
These figures are calculated over the last 30 minutes in
periods of 5 minutes.


60 % Hybrid Use
corresponds to 60 % of the cumulative
running time with the addition of the Hybrid4 system and
40 % of the time with the Diesel engine only.

For more information on the trip computer, refer to the
corresponding section.



Fuel consumption

13Hybrid4 system
Tr i p c o m p u t e r


System that gives you information on the current journey (range, fuel consumption…).












Instrument panel screen



Information display



)
Press the end of the wiper control stalk
to
display the various tabs in succession.



- The current information tab with:


●
the range,

●
the current instantaneous fuel
consumption.





- Tr i p "1"
with:


●
the average speed,

●
the average fuel consumption,
for the first trip.





- Tr i p "2"
with:


●
the average speed,

●
the average fuel consumption,
for the second trip.


Trips "1"
and "2"
are independent but their use
is identical.
For example, trip "1"
can be used for daily
figures, and trip "2"
for monthly figures.


- The energy flows.


Resetting the trip recorder



)
When the desired trip is displayed, press
the end of the wiper control stalk for more
than two seconds.



Resetting the histogramme
(Only with touch screen)



)
When trip "2"
is displayed, press the end
of the wiper control stalk for two seconds to
reset the fuel consumption histogramme.


- The radio or media playing.

- Navigation instructions.

Touch screen


Information display


The current instantaneous fuel consumption tab with:


- the range,

- the current fuel consumption.


The trip "1"
tab with:


- the average speed,

- the average fuel consumption,
for the first trip.


The trip "2"
tab with:


- the average speed,

- the average fuel consumption,
for the second trip.


The energy flows.
The fuel consumption histogram.




Trip reset



)
Select the "

Driving " menu.
The trip computer information is displayed in
the primary page of the menu.


)
Press one of the buttons to display the
desired tab.


)
When the desired trip is displayed,
press the reset button or press and
hold the end of the wiper control stalk.

Trips "1"
and "2"
are independent but their use
is identical.
For example, trip "1"
can be used for daily
figures, and trip "2"
for monthly figures.


Resetting the histogram



)
When trip "2"
is displayed, pressing
the reset button also resets the fuel
consumption histogram.




1.
"Instantaneous".


2.
"Trip 1".


3.
"Trip 2".


4.
"Hybrid".


5.
"Histogram".


6.
"00.0 / Reset".

15Hybrid4 system

Starting the Hybrid4 system


Activation of the Hybrid4 system

On activation of the Hybrid4 system, the
instrument panel lights up, the power indicator
needle is placed at position " 0
". The steering
column automatically unlocks (perceptible
noise and movement of the steering column).
Depending on certain parameters, such as the
state of charge of the high voltage battery or
the ambient temperature, the Hybrid4 system
itself determines whether it is necessary to
start the HDi Diesel engine.
The mode selector is at the AUTO
position.

In wintry conditions with the
engine cold, the Diesel pre-
heating warning lamp can stay
on for a few seconds; wait until
it goes off before releasing the
brake pedal.






























Starting - switching off the Hybrid4 system


Never leave children alone inside the
vehicle when the Hybrid4 system is
active.



)
Place the gear selector at position N
.

)
Insert the electronic key in the reader.
or


)
With Keyless Entry and Starting, simply
having the electronic key inside the vehicle
is sufficient.
)
Press the brake pedal firmly.


)
Make a single short press (about one
second) on the " START/STOP
" button.

)
Maintain pressure on the brake pedal until
the READY
lamp comes on, signalling
activation of the Hybrid4 system, confirmed
by an audible signal.

If the Hybrid4 system does not activate:


)
If N
is flashing in the instrument
panel, move the gear selector to
position A
then to position N
.

)
If the " Foot on the brake
" is
displayed, press the brake pedal
firmly.


The READY
lamp may come on after
a few seconds if there is a demand
for activation of the Hybrid4 system
after energy economy mode has been
entered.

Moving off


For more information on the
electric parking brake, refer to the
corresponding section in the handbook
for the vehicle.

You can change the operating mode of the
Hybrid4 system at any time using its mode
selector.
Driving in ZEV
mode requires that particular
conditions be met.

When your vehicle vehicle moves off
in electric mode, it makes no noise. Be
very careful of pedestrians, cyclists...
as, because of this, they will not hear
you coming.

Head-up display

The colour of the speedometer varies
according to the drive train used:


- white display: Diesel engine
running,

- blue display: Diesel engine
stopped.

Using automatic mode with the
electronic gearbox optimises gear
changes and so gives more economical
driving.


)
If automatic operation of the electric
parking brake has been deactivated, pull
then release the control lever to release the
parking brake manually.

)
Progressively release the brake pedal.

)
With the parking brake released, the
vehicle then moves off.
If the parking brake is still applied and is in
automatic mode, accelerate progressively.

)
Move the gear selector to
position A
(automatic mode) or M
(manual
mode) or R
(reverse).

17Hybrid4 system

Switching off the Hybrid4 system




)
Immobilise the vehicle.

)
Place the gear selector in position N
.

)
Make a short press (about one second) on
the " START/STOP
" button.
The Hybrid4 stops:


- the READY
lamp goes off,

- the steering column locks,

- the electric parking brake is applied
automatically, unless its automatic mode is
deactivated.


)
Check that the parking brake warning
lamps are on.

)
Remove the electronic key from the reader.

Before doing anything under the
bonnet, the Hybrid4 must be switched
off ( READY
lamp off) and the electric
parking brake must be applied.

Check that the READY
lamp is off
before leaving the vehicle.
Never leave the electronic key in the
vehicle in your absence.





For reasons of safety and theft protection,
do not leave your electronic key in the
vehicle, even when you are close to it.
It is recommended that you keep it on
your person.
















Switching the ignition on


With the electronic key in the reader or the
Keyless Entry and Starting key inside the
vehicle, pressing the " START/STOP
" button,
with no action on the brake pedal
, allows the
ignition to be switched on.



)
Press the " START/STOP
"
button, the instrument panel
comes on but the Hybrid4 system
does not start up.

With the ignition on, the system goes
into energy economy mode when
necessary to maintain the state of
charge of the battery.

)
Press this button again to switch off the
ignition and so allow the vehicle to be
locked.

Back-up starting / emergency switching off


Back-up starting with the
Keyless Entry and Starting
system
When the electronic key is in the recognition
zone and after pressing the " START/STOP
"
button, the Hybrid4 system does not start up:


)
Insert the electronic key in the reader.

)
Place the gear selector at position N
.

)
Press the brake pedal firmly.

)
Press the " START/STOP
" button.
The Hybrid4 starts up; the READY
lamp is on.




















Electronic key not recognised
with Keyless Entry and Starting
If the electronic key is no longer in the
recognition zone when driving or when you
(later) request switching off of the Hybrid4
system, a message appears in the instrument
panel.


)
Press and hold the " START/STOP
" button
for about 3 seconds if you want to force the
Hybrid4 system to switch off. In the event of an emergency only, the engine
can be switched of without any conditions.


)
To do this, press and hold the " START/
STOP
" button for about 3 seconds.
In this case the steering column locks as soon
as the vehicle stops.

The electronic key must always remain
inside the vehicle when in use.



Emergency switching off

Note that restarting will not be possible
without the presence of the electronic
key in the recognition zone.