2016 CITROEN DS3 CABRIO DAG turn signal

35
DS3_en_Chap01_controle-de-marche_ed01-2015
With the engine running, when the needle is:
- i n zone A ,
  the   temperature   is   correct,
-

i
n zone B,   the   temperature   is   too   high;  
t

he central STOP
 
warning   lamp   and   the  
m

aximum   temperature   warning   lamp 1
come
  on   in   red,   accompanied   by   an  
a

udible   signal   and   a   message   in   the  
m

ultifunction
 s
creen.
You must stop as soon as it is safe to do so.
Wait
  a   few   minutes   before   switching   off   the  
e

ngine.
Contact
  a   CITROËN   dealer   or   a   qualified  
w

orkshop.
Coolant temperature indicator
After driving for a few minutes, the temperature and   pressure   in   the   cooling   system   increase.
To
  top   up   the   level:
F
 
w
ait   for   the   engine   to   cool   down,
F

u
nscrew the cap by two turns to allow the
pressure to drop,
F
 
w
hen   the   pressure   has   dropped,   remove  
t

he cap,
F
 
t
op   up   the   level   to   the   "MA X"   mark.
Monitoring

103
DS3_en_Chap04_conduite_ed01-2015
To facilitate unlocking of the steering column,   put   the   front   wheels   in   the  
s

traight  
a
head  
p
osition  
b
efore  
s
witching  
t

he   ignition   off.
Never
  switch   the   ignition   off   until   the
 v

ehicle   has   come   to   a   complete   stop
 a

nd   the   parking   brake   has   been   applied.
 W

ith   the   engine   stopped,   the   braking   and
 s

teering   assistance   systems   are   also   cut
 o

ff:   risk   of   loss   of   control   of   the   vehicle.When
  you   leave   the   vehicle,   take   the  
k

ey   with   you   and   lock   the   vehicle.
For   more   information,   refer   to   the  
"

Energy   economy   mode"   section.
Key reminder
If the key is left in the ignition switch, an audible   signal   sounds   when   the   driver's  
d

oor   is   opened.
Switching the engine off
F Immobilise   the   vehicle.
F  W ith   the   engine   at   idle,   turn   the   key   fully  
t

owards you to position 1 (Stop) .
F
 
R
emove   the   key   from   the   ignition   switch.
F
 
T
o   lock   the   steering   column,   turn   the  
s

teering   wheel   until   it   locks.
F
 
E
nsure   that   the   parking   brake   is   applied  
c

orrectly,   particularly   when   on   a   slope.
Energy economy mode
After switching off the engine (position  1
- Stop),
  you   can   still   use   functions  
s

uch   as   the   audio   and   telematic   system,   the  
w

ipers,   dipped   beam,   courtesy   lamps,   etc.,   for  
m

aximum   cumulative   period   of   30   minutes.
driving

DS3_en_Chap04_conduite_ed01-2015
When you move the selector in the gate to select   a   position,   the   corresponding   indicator   is  
d

isplayed   in   the   instrument   panel.
P.
 Pa

rk
R.
R

everse
n. N

eutral
d

.
 D
rive   (Automatic   driving)
S.
Sport
 pro
gramme
T .
Snow
 pro
gramme
1 2 3 4.
  
G
ears   engaged   during   manual  
ope

ration
-.
 I

nvalid   value   during   manual   operation
displays in the instrument panel
Foot on brake
F Press  the   brake   pedal   when   this  i
ndicator   lamp   is   displayed   in   the  
i

nstrument   panel   (e.g.:   starting  
t

he
 eng
ine).
Moving off
If position n is selected inadvertently
w hile   driving,   allow   the   engine   to  
r

eturn to idle then select position d to
accelerate.
If
  the   ambient   temperature   is  
b

elow -23°C,   the   engine   should   be   left  
a

t   idle   for   four   minutes,   to   ensure   the  
c

orrect   operation   and   life   of   the   engine  
an

d
 g
earbox. When
  the   engine   is   running   at   idle,   with  
t

he   brakes   released,   if   position   R
, d or
M   is   selected,   the   vehicle   moves   even  
w

ithout   the   accelerator   being   pressed.
When   the   engine   is   running,   never  
l

eave children in the vehicle without
supervision.
When   carrying   out   maintenance   with  
t

he   engine   running,   apply   the   parking  
b

rake   and   select   position   P
.
F
 
A

pply   the   parking   brake.
F

Sel
ect position P or n
.
F

 
S

tart   the   engine.
If this procedure is not followed, there is an
audible   signal,   accompanied   by   the   display   of  
a

n
 
warning   message.
F
 
W
ith   the   engine   running,   press   the   brake  
ped

al.
F
 
R

elease   the   parking   brake.
F

Sel
ect position R
, d or M
.
F
 
G

radually   release   the   brake   pedal.
The
 
vehicle   moves   off   immediately.

DS3_en_Chap04_conduite_ed01-2015
There is a risk of damage to the gearbox:
- i f you press the accelerator and
brake
  pedals   at   the   same   time,
-
 
i
f   you   force   the   movement   of   the  
s

elector   from   the   P position to
another position when the battery
is
  flat.
To
  reduce   fuel   consumption   when   at
 a

  prolonged   standstill   with   the   engine
 r

unning   (traffic   jam...),   put   the   selector   in
 t

he
n  

position   and   apply   the   parking   brake.
If the selector is not in position P
,
when
 
the
 
driver's
 
door
 
is
 
opened
 
or
 
a

pproximately
 
45
 
seconds
 
after
 
the
 
i

gnition
 
is
 
switched
 
off,
 
a
 
warning
 
m

essage
 
appears
 
in
 
the
 
screen.
F

R

eturn the selector to position P ;
 
t

he
 
message
 
disappears.
When
 
driving
 
on
 
flooded
 
roads
 
or
 
when
 
c

rossing
 
a
 
ford,
 
proceed
 
at
 
walking
 
p

ace.
Operating fault
Manual operation
When the ignition is on, the lighting o
f   this   warning   lamp,   accompanied  
b

y
 
an
 
audible   signal   and   a   message   in   the  
m

ultifunction   screen,   indicates   a   gearbox   fault.
In
 
this
 
case,   the   gearbox   switches   to   back-up  
m

ode
 
and
 
is   locked   in   3rd   gear.   You   may   feel  
a

 
substantial   knock   when   changing   from   P
to R
 
and
 
from  n to R .
  This   will   not   cause   any  
d

amage
 
to
 
the   gearbox.
Do
 
not
 
exceed   60   mph   (100   km/h),   local   speed  
r

estrictions
 p
ermitting.
Contact
 
a
 
CITROËN   dealer   or   a   qualified  
w

orkshop
 
as   soon   as   possible.
F
Sel
ect position M for sequential c
hanging o
f
 
the
 
four
 
gears.
F

P

ush the selector towards the +
 
sign
 
to
 
c

hange
 
up
 
a
 
gear.
F

P

ull the selector towards the -
 
sign
 
to
 
c

hange
 
down
 
a
 
gear.
It
 
is
 
only
 
possible
 
to
 
change
 
from
 
one
 
gear
 
to
 
a

nother
 
if
 
the
 
vehicle
 
speed
 
and
 
engine
 
speed
 
p

ermit;
 
other wise,
 
the
 
gearbox
 
will
 
operate
 
t

emporarily
 
in
 
automatic
 
mode. This
 
symbol
 
is
 
displayed
 
if
 
a
 
gear
 
i

s
 
not
 
engaged
 
correctly
 
(selector
 
b

etween
 
two
 
positions).
d

 
disappears
 
and
 
the
 
gears
 
e

ngaged
 
appear
 
in
 
succession
 
in
 
the
 
in

strument
 pan

el.
Stopping the vehicle
Before switching off the engine, you can engage p osition P or
n 
to   place   the   gearbox   in   neutral.
In
  both   cases,   apply   the   parking   brake   to  
i

mmobilise   the   vehicle.
Invalid value during manual
operation
If the engine speed is too low or too high, the gear   selected   flashes   for   a   few   seconds,   then  
t

he   actual   gear   engaged   is   displayed.
It
  is   possible   to   change   from   position  d
(automatic)
  to   position   M   (manual)   at   any   time.
When
  the   vehicle   is   stationary   or   moving  
v

ery   slowly,   the   gearbox   selects   gear   M1
automatically.
The
  sport   and   snow   programmes   do   not  
o

perate   in   manual   mode.

133
DS3_en_Chap05_visibilite_ed01-2015
The temporary illumination of the dipped beam headlamps   after   the   vehicle's   ignition   has   been  
s

witched   off   makes   the   driver's   exit   easier  
w

hen   the   light   is   poor.
Switching on
F With  the   ignition   off,   "flash"   the   headlamps  u
sing   the   lighting   stalk.
F
 
A
  further   "headlamp   flash"   switches   the  
f

unction   off.
Switching off
The manual guide-me-home lighting switches off   automatically   after   a   set   time.
Manual guide-me-home
lighting
The sidelamps and dipped beam headlamps are   switched   on   automatically,   without   any  
a

ction on the part of the driver, when a low level
of
  external   light   is   detected   or   in   certain   cases  
o

f   activation   of   the   windscreen   wipers.
As
  soon   as   the   brightness   returns   to   an  
a

dequate   level   or   after   the   windscreen   wipers  
a

re   switched   off,   these   lamps   are   switched   off  
a

utomatically   and   the   daytime   running   lamps  
c

ome   on.
Automatic illumination of
headlamps
Activation
F Turn   ring   to   the   "AUTO"  position.   The  a
ctivation   of   the   function   is   confirmed   by  
t

he   display   of   a   message.
deactivation
F Turn  ring   to   a   position   other   than   "AUTO".  T
he deactivation of the function is
confirmed
  by   the   display   of   a   message.
Operating fault
In the event of a fault with the
sunshine  sensor,   the   lighting   come  
o

n,   this   warning   lamp   is   displayed  
o

n   the   instrument   panel   and/or   a  
m

essage   appears   in   the   screen,  
a

ccompanied   by   an   audible   signal.
Contact
 
a
 
CITROËN   or   a   qualified   workshop  
w

orkshop.
Visibility

DS3_en_Chap08_info-pratiques_ed01-2015
Important:   if   your   vehicle's  Ad
Blue® tank is completely empty - w
hich
 
is
  confirmed   by   the   alert  
m

essages   and   the   impossibility   of  
s

tarting
 
the   engine,   you   must   add   at  
l

east
 
3.8   litres   (so   two   1.89   litre   bottles).If any additive is split or splashed, wash
immediately
  with   cold   water   or   wipe  
w

ith   a   damp   cloth.
If the additive has crystallised, clean it
off   using   a   sponge   and   hot   water.Important:
 i
n the event of a top-up after
a breakdown because of a lack of
additive ,   signalled   by   the   message   "Top
 u

p   emissions   additive:   Starting   prevented",
 y

ou   must   wait   around   5   minutes   before
 s

witching  
o
n  
t
he  
i
gnition,  
w
ithout opening
the driver's door, locking the vehicle
or introducing the key into the ignition
switch .
Switch   on   the   ignition,   then,   after
 1

0 seconds,   start   the   engine.
F

O

btain a bottle of AdBlue
®. After first c
hecking
 
the
 
use-by
 
date,
  read   carefully  
t

he instructions on use on the label before
pouring
 
the
 
contents
 
of
 
the   bottle   into   your  
v

ehicle's
 Ad

Blue
® tank. N ever dispose of AdBlue
® additive
bottles
 
in
 
the
 
household
 
waste.   Place  
t

hem
 
in
 
a
 
special
 
container   provided  
t

his
 
purpose
 
or
 
take
 
them
  to   your  
d

ealer.
F
 
A

fter
 
emptying
 
the
 
bottle,
 
wipe
 
away
 
any
 
s

pillage
 
around
 
the
 
tank
 
filler
 
using
 
a
 
damp
 
c

loth.
F
 
R

efit
 
the
 
blue
 
cap
 
to
 
the
 
tank
 
and
 
turn
 
it
 
a


6
th of a turn clockwise, to its stop.
F
 R
efit   the   black   cap   and   turn   it   a   quarter   of  
a

 
turn   clockwise   without   pressing.   Ensure  
t

hat the indicator on the cap lines up with
the
 
indicator   on   the   support.
F
 
D

epending   on   equipment,   return   the   spare  
w

heel   and/or   the   storage   box   to   the   bottom  
o

f
 
the   boot.
F
 
R

efit   the   boot   carpet   and   close   the   tailgate.

2Driving

Moving off


If position N
is selected inadvertently
while driving, allow the engine to
return to idle then select position D
to
accelerate.
If the ambient temperature is below
-23°C, the engine should be left at idle
for four minutes, to ensure the correct
operation and life of the engine and
gearbox.
When the engine is running at idle, with
the brakes released, if position R
, D
or
M
is selected, the vehicle moves even
without the accelerator being pressed.
When the engine is running, never
leave children in the vehicle without
supervision.
When carrying out maintenance with
the engine running, apply the parking
brake and select position P
.


)
Apply the parking brake.

)
Select position P
or N
.

)
Start the engine.
If these conditions are not met, there is an
audible signal, accompanied by the display of
an warning message.


)
With the engine running, press the brake
pedal.

)
Release the parking brake.

)
Select position R
, D
or M
.

)
Gradually release the brake pedal.
The vehicle moves off immediately.

4Driving

If the selector is not in position P
,
when the driver's door is opened or
approximately 45 seconds after the
ignition is switched off, a warning
message appears in the screen.


)
Return the selector to position P
;
the message disappears.
When driving on flooded roads or when
crossing a ford, proceed at walking
pace.



Manual operation



)
Select position M
for sequential
changing
of the six gears.

)
Move the selector towards the +
sign to
change up a gear.

)
Move the selector towards the -
sign to
change down a gear.
It is only possible to change from one gear to
another if the vehicle speed and engine speed
permit; other wise, the gearbox will operate
temporarily in automatic mode. This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).


D
disappears and the gears
engaged appear in succession in the
instrument panel.

Stopping the vehicle

Before switching off the engine, you can
engage position P
or N
to place the gearbox in
neutral.
In both cases, apply the parking brake to
immobilise the vehicle.

Invalid value during manual
operation
If the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D

(automatic) to position M
(manual) at any time.
When the vehicle is stationary or moving
very slowly, the gearbox engages first gear
automatically. When the ignition is on, the lighting
of this warning lamp, accompanied

Operating fault
by an audible signal and a message in the
multifunction screen, indicates a gearbox fault.
In this case, the gearbox switches to back-up
mode and is locked in 3rd gear. You may feel
a substantial knock when changing from P

to R
and from N
to R
. This will not cause any
damage to the gearbox.
Do not exceed 60 mph (100 km/h), local speed
restrictions permitting.
Contact a CITROËN dealer or a qualified
workshop as soon as possible.

There is a risk of damage to the gearbox:


- if you press the accelerator and
brake pedals at the same time,

- if you force the movement of the
selector from the P
position to
another position when the battery is
flat.
To reduce fuel consumption when at
a prolonged standstill with the engine
running (traffic jam...), put the selector
in the N
position and apply the parking
brake.