104
C1_en_Chap05_eclairage-visibilite_ed01-2016
Wiper control stalk
Manual controls
The wipers are controlled directly by the driver.
Windscreen wipers
Wiping speed control stalk: raise or lower the stalk to the desired position.
Single
wipe.
Park.
Intermittent
wipe.
Normal
wipe (moderate rain).
Fast
wipe (heavy rain).
Do
not
operate
the
wipers
on
a
dry
w
indscreen.
Under
extremely
hot
or
c
old
conditions,
ensure
that
the
wiper
b
lades
are
not
stuck
to
the
windscreen
b
efore
operating
the
wipers.
In
wintry
conditions,
remove
snow,
ice
o
r
frost
present
on
the
windscreen,
a
round
the
wiper
arms
and
blades
and
t
he
windscreen
seal,
before
operating
t
he
wipers.
For
a single wipe of the windscreen, raise and
r
elease the control stalk.
Lighting and visibility
105
C1_en_Chap05_eclairage-visibilite_ed01-2016
Rear wiperRear screenwash
Wiper off, turn the control stalk towards you to o
perate the rear screenwash, accompanied by
s
everal sweeps of the rear wiper.
Windscreen wash
Turn the ring to this position for a steady wipe.
Pushing
the stalk away from you operates the
w
ash
during wiping.
Pull
the
wiper
stalk
towards
you.
T
he windscreen
wash,
then
the
windscreen
w
ipers,
operate
for
a
pre-determined
time.
Do not use the front or rear screenwash
when the screenwash reservoir is
empty.
You risk damaging the pump.
5
Lighting and visibility
110
C1_en_Chap06_securite_ed01-2016
Active City Brake
Active City B rake i s a d riving a ssistance s ystem t
hat aims to avoid a frontal collision or reduce
t
he speed of an impact if the driver does not
r
eact or reacts too late (brake application too
l
ate). This
system is designed to improve
d
riving safety.
It
remains the driver's responsibility to
c
ontinuously monitor the state of the
t
raffic and to assess the distances and
r
elative speeds of other vehicles.
Active
City Brake can in no
c
ircumstances replace the need for
v
igilance on the part of the driver.
Never
look at the laser sensor through
a
n optical instrument (magnifying glass,
m
icroscope...) at a distance of less than
1
0 centimetres: risk of eye injury.Automatic
braking occurs later than if
d
one by the driver, so as to intervene
o
nly when there is a high risk of
c
ollision.Principle
Using a laser sensor and a camera located at the top of the windscreen, this system detects
a
vehicle running in the same direction or
s
tationary ahead of your vehicle.
When
necessary, the vehicle's braking system
i
s operated automatically to reduce the speed
o
f impact or to help avoid a collision with the
v
ehicle
a
head.
Conditions for activation
Active City Brake only operates if the following
c onditions are met:
●
t
he engine is running,
●
t
he vehicle is in a for ward gear,
●
t
o trigger the pre-collision alert :
-
t
he speed is between 9 and 87 mph
(
15 and 140 km/h),
-
t
he difference in speed between your
v
ehicle and the one ahead is more than
a
bout 9 mph (15 km/h),
●
f
or braking assistance :
-
t
he speed is between about 18 and
5
0 mph (30 and 80 km/h),
-
t
he difference in speed between your
v
ehicle and the one ahead is more than
a
bout 18 mph (30 km/h),
●
f
or automatic pre-collision braking:
-
t
he speed is between about 6 and
5
0 mph (10 and 80 km/h),
-
t
he difference in speed between your
v
ehicle and the one ahead is more than
a
bout 6 mph (10 km/h),
●
t
he braking assistance systems (ABS,
E
BFD, EBA) are not faulty,
●
t
he trajectory control systems (TRC, DSC)
a
re not deactivated or faulty,
●
t
he vehicle is not in a tight corner,
●
t
he system has not been triggered during
t
he previous 10 seconds.
Safety
114
C1_en_Chap06_securite_ed01-2016
Operating faults
Sensor fault
The operation of the laser sensor may suffer inter ference from accumulations of dirt or
m
isting of the windscreen or the presence of
a
n object causing an obstruction (e.g.: bonnet
ope
n). In
this case you are warned by the
d
isplay of this flashing warning lamp
i
n the instrument panel.
Use
the windscreen demisting and regularly
c
lean the area of the windscreen in front of the
sen
sor.Do
not stick or other wise fix any object
o
n the windscreen in front of the sensor.
System fault
In the event of a malfunction of the system, you are warned by the
d
isplay of this flashing warning lamp
i
n the instrument panel.
Have
the
system checked by a CITROËN
d
ealer
or
a qualified workshop.
In
the event of an impact to the
w
indscreen at the sensor, deactivate
t
he
system and contact a CITROËN
d
ealer or a qualified workshop to have
y
our windscreen replaced.
Never
try to remove, adjust or test the
sen
sor.
Only
a CITROËN dealer or a qualified
w
orkshop is able to work on the system.
Safety
116
C1_en_Chap06_securite_ed01-2016
Seat belt not fastened /
unfastened warning lamps
1. Front seat belts not fastened / unfastened w
arning lamp, in the instrument panel.
2.
L
eft
h
and
r
ear
s
eat
b
elt
u
nfastened
w
arning
l
amp, in the seat belts and passenger's
f
ront airbag display screen.
3.
R
ight hand rear seat belt unfastened
w
arning lamp, in the seat belts and
p
assenger's front airbag display screen.Rear seat belt warning lamp(s)
The warning lamp(s) 2 and/or 3 come on in the seat belts and passenger's front airbag warning
l
amp display screen when one or more rear
p
assengers
u
nfasten
t
heir
sea
t
b
elt.
From
about 12 mph (20 km/h) and for about
30
seconds, illumination of the warning lamp is
a
ccompanied by an audible signal.
Beyond
this time, if the seat belt is still not
f
astened, the tone of the audible signal
c
hanges and remains active for about a further
9
0 seconds.
If
you
place
a
load
on
the
front
p
assenger
seat,
this
may
cause
the
w
arning
lamp
to
come
on.
Front seat belt(s) warning lamp
The warning lamp 1 comes on in the instrument p anel if the front seat belt is not fastened or is
u
nfastened.
From
about 12 mph (20 km/h) and for about
30
seconds, illumination of the warning lamp is
a
ccompanied by an audible signal.
Beyond
this time, if the seat belt is still not
f
astened, the tone of the audible signal
c
hanges and remains active for about a further
9
0 seconds.
Safety
119
C1_en_Chap06_securite_ed01-2016
Deactivating the passenger's
front airbag
Only the passenger's front airbag can be deactivated.
F
W
ith the ignition off ,
insert the key in the
p
assenger airbag deactivation switch.
F
T
urn it to the "OFF"
p
osition.
F
R
emove the key keeping the switch in the
n
ew position.When
the ignition is on, this warning
l
amp comes in the seat belt and
p
assenger's front airbag display
s
creen. It stays on while the airbag is
d
eactivated. To
assure the safety of your child,
t
he passenger's front airbag must be
d
eactivated when you install a rear ward
f
acing child seat on the front passenger
sea
t.
Other wise, the child would risk being
s
eriously injured or killed if the airbag
w
ere deployed.
Reactivating the passenger's
front airbag
When you remove a rear ward facing child seat, w
ith the ignition off , turn the switch to the
"ON"
position to reactivate the airbag and so
a
ssure the safety of your front passenger in the
e
vent of an impact.
When
the ignition is switched on, this
w
arning lamp comes on in the seat
b
elt and passenger's front airbag
d
isplay screen. It stays on while the
f
ront airbag is activated.
Operating fault
Illumination of this warning lamp in the instrument panel indicates a fault
w
ith the airbags.
Contact
a
CITROËN dealer or a qualified
w
orkshop
without delay to have the system
c
hecked.
The airbags may no longer be
d
eployed
in the event of a serious impact.
In
this
case, do not install a child seat or seat
a
n
adult
on the front passenger seat.
6
Safety
141
C1_en_Chap07_info-pratiques_ed01-2016
Electrical energy economy mode*
System which manages the duration of use of certain functions to conserve a sufficient level of charge in the battery.
After
the engine has stopped, you can still use functions such as the audio system, windscreen
w
ipers, dipped beam headlamps, courtesy lamps, etc. for a maximum combined duration of
t
wenty minutes.
This
period may be greatly reduced if the battery is not fully charged.
Let
the engine run for the duration
s
pecified to ensure that the battery
c
harge is sufficient.
Do
not repeatedly and continuously
r
estart the engine in order to charge the
b
attery.
A
flat battery prevents the engine from
s
tarting.
Refer
to the "Battery" section.
Switching to economy mode
Once this time has elapsed the active functions are put on standby.
Exiting economy mode
These functions are reactivated automatically next time the vehicle is driven.
To restore the use of these functions
immediately,
start the engine and let it run for at
l
east 5 minutes.
*
O
nly on vehicles with the "Keyless Entry and
S
tarting" system.
7
Practical information
144
C1_en_Chap07_info-pratiques_ed01-2016
Fitting roof bars
When fitting transverse roof bars, use the accessories recommended by CITROËN and
f
ollow the manufacturer's fitting instructions.
For
more information, contact a CITROËN
d
ealer or a qualified workshop. Please
refer to national legislation in
o
rder to comply with the regulations
c
oncerning the transportation of objects
w
hich are longer than the vehicle.
Maximum weight authorised on the bars,
for a loading height not exceeding 40 cm
(except bicycle carrier): 40 kg.
If the height exceeds 40 cm, adapt the
speed of the vehicle to the profile of the
road to avoid damaging the roof bars.
Changing a wiper
b
lade
Removing the front wiper blade
F Raise the wiper arm.
F R emove the wiper blade, sliding it towards
t
he outside.
Fitting the front wiper blade
F Put the corresponding new wiper blade in p
lace and fix it.
F
F
old down the wiper arm carefully.
To conserve the effectiveness of
the
flat-blade type wiper blades, we
r
ecommend that they are:
-
h
andled with care,
-
c
leaned regularly with soapy water,
-
n
ot used to hold a cardboard sheet
a
gainst the windscreen,
-
r
eplaced at the first signs of wear.
Practical information