2016 Citroen BERLINGO MULTISPACE RHD wheel

148
Towing a trailer
Berlingo-2-VP_en_Chap06_Accessoire_ed02-2015
For more information about weights and towed loads, refer to
chapter  9,   "Weights"   section.
TOWING A TRAILER , A CARA VAN ...
Distribution of loads
d

istribute the load in the trailer so
that
  the   heaviest   objects   are   as  
close as possible to the axle and
the nose weight is close to the
maximum

  authorised   without,   however,  
exceeding

  it.
Cooling
Towing a trailer on a slope increases
the
  coolant   temperature.a s the fan is electrically controlled, its
cooling capacity is not dependent on
the
  engine   speed.
You should therefore use a high gear
to lower the engine speed and reduce
your
  speed.
In all cases, pay attention to the
coolant
  temperature.
Driving advice
A towed   vehicle   must   free   wheel:  gearbox
  in   neutral.

150
Towing a trailer
Berlingo-2-VP_en_Chap06_Accessoire_ed02-2015
TOWBAR WITH SWAN NECK T
OWBALL ,
LOCKABLE

AND
QUICKL
Y
DET

ACHABLE
Presentation
This swan neck towbar, delivered assembled,   can   be   removed   and   fitted  
easily

.   No   tools   are   needed.
Instructions for fitting and before
every use
Check
  that   the   swan   neck   is   correctly  
locked

  by   verifying   the   following   points:
-
 
the
  green   mark   on   the   locking  
wheel is visible
-

 
the
  safety   lock   on   the   locking   wheel  
is directed toward the rear

,
-
 
the
  safety   lock   is   closed   and   the  
key

  removed;   the   locking   wheel   can  
no longer be operated,
-

 
the
  swan   neck   must   no   longer  
move

  at   all   in   its   carrier.
When
  hooking   up   the   trailer,   don't  
forget

  to   connect   the   trailer   harness.
Fitting

152
Berlingo-2-VP_en_Chap06_Accessoire_ed02-2015
Equipment
Berlingo-2-VP_en_Chap06_Accessoire_ed02-2015
OTHER ACCESSORIES
These accessories and parts, having
been tested and approved for reliability
and safety, are all adapted to your
vehicle. 
A 
wide   range   of   recommended  
accessories and genuine parts is
available.
a further range is also available,
structured

  around   comfort,   leisure   and  
maintenance:
Anti-theft

  alarm,   window   etching,   first  
aid

  kit,   high   visibility   vest,   front   and  
rear

  parking   sensors,   warning   triangle,  
security

  bolts   for   alloy   wheels, ...
Seat
  covers   compatible   with   airbags  
for the front seats, bench seat, rubber
mats,

 
carpet
 
mats,
 
snow
 
chains,
 
blinds,
 
tailgate

  bicycle   carrier,   ...
To
  prevent   the   mat   from   becoming  
caught

  under   the   pedals:
-
 
ensure
  that   the   mat   and   its   fixings  
are positioned correctly

,
-
 
never
  fit   one   mat   on   top   of   another.Audio
  equipment,   hands-free   kit, speakers,
  CD   changer,   satellite navigation

 
system,
 
USB
 
box,
 
V
ideo  
kit, 
...
Regardless
  of   the   audio   and   telematic
 equipment

  offered   on   the   market,   the
 technical constraints associated with


the
  fitting   of   equipment   of   these   product
 groups

  mean   that   the   special   features
 of

  the   equipment   and   its   compatibility
 with the capacities of your vehicle's


standard
  equipment   must   be   taken   into
 account.

  Please   ask   a   CITROËN   dealer
 for

  more   information   before   fitting   such
 equipment.
Maximum weights on bars
-


T
ransverse bars on longitudinal
bars:
  75   Kg   (these   bars   are   not  
compatible

  with   the   Modutop   roof).
Installing radiocommunication
transmitters
You are advised to contact a CITR
o Ë n
dealer before installing accessory
radiocommunication
  transmitters   with  
external

  aerial   on   your   vehicle.
The
  CITROËN dealer   network  
will

  inform   you   of   the   specification  
(frequency

  band,   maximum   output  
power

,   aerial   position,   specific  
conditions of installation) of the
transmitters

  which   can   be   fitted,   in  
accordance with the Motor V

ehicle
Electromagnetic
  Compatibility  
Directive (2004/104/EC).Front

  mud   flaps,   rear   mud   flaps,  15/17 inch
  alloy   wheels,   wheelarch  
trim,

  leather   steering   wheel,   ...
Screenwash, interior and exterior
cleaning
  and   maintenance   products,  
spare

  bulbs,   ...
The
  fitting   of   electrical   equipment  
or accessories which are not
recommended

  by   CITROËN   may  
result in a failure of your vehicle's
electronic

  system.   Please   note   this  
specific

  warning.  
Y
ou   are   advised  
to contact a dealer to be shown the
range

  of   recommended   equipment   or  
accessories.
d

epending on the country in which
the
  vehicle   is   sold,   it   is   compulsory  
to have a high visibility vest, warning
triangle and spare bulbs available in
the

  vehicle.

171
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
The temporary tyre repair kit consists of  a   compressor   and   a   bottle  
(containing

  a   sealant).
Using the kit
1. Tick  the   deflated   wheel   on   the  speed
  limitation   sticker   then   affix  
the

  sticker   to   the   vehicle's   steering  
wheel

  to   remind   you   that   a   wheel   is  
in

  temporary   use.
2.

Clip the bottle
1 on the
compressor 2.
3.

Connect the bottle
1 to the valve of
the
  tyre   to   be   repaired.
4.
 
T
ake   care   to   unwind   the  
compressor

  pipe   before   connecting  
it

  to   the   bottle.
5.

Connect the power lead to one of
the

  vehicle's   12V   sockets.
6.
 
Switch
  on   the   compressor   by  
pressing button

A until the tyre
pressure
  reaches   2.0   bars.   If   this  
pressure cannot be reached, the
tyre

  cannot   be   repaired.
7.
 
Remove
  and   store   the   compressor.
8.
 
Drive
  immediately,   for   a   few   miles  
(kilometres),

  at   reduced   speed,  
to
  fill   the   puncture.
9.
 
Adjust
  the   pressure   using   the  
compressor

  in   accordance   with   the  
recommendation

 
for
 
the
 
vehicle
 
and
 
check

  that   the   leak   is   filled   correctly  
(no

  further   loss   of   pressure).
10.
 
Drive
  at   reduced   speed   (50 mph  
[80

  km/h]).  
The
  tyre   must   be  
examined

  and   repaired   by   a  
specialist

  as   soon   as   possible.
a
fter use, the bottle can be stored in
a   plastic   bag,   supplied   in   the   kit,   to  avoid staining your vehicle with traces
of
  fluid.
Warning:
  the   bottle   of   gel   contains  
ethylene-glycol, a product which
is

  harmful   if   swallowed   and   which  
causes

  irritation   to   the   eyes.
Keep
  it   out   of   reach   of   children.
a

fter use, do not discard the bottle into
the
  environment,   take   it   to   a   CITROËN  
dealer or to an specialised waste
disposal

  site.
Replacement
  bottles   of   sealant   are  
available

  from   CITROËN   dealers.
TEMPORARY PUNCTURE
REP

AIR KIT
The kit is located in one of the two storage   compartments   located  
under

  the   front   seats.
Vehicles
  supplied   with   a   temporary  
puncture

  repair   kit   do   not   have   a   spare  
wheel

  or   tooling   (jack,   wheelbrace,   ...).
QUICk HELP
8
Changing a wheel

172
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
1. Parking the vehicle
- The  occupants   must   get   out   of   the  vehicle
  and   wait   in   a   safe   location.
-
 
If
  possible,   park   the   vehicle   on  
level, stable and non-slippery
ground.
-

 
Apply
  the   parking   brake,   switch  
of

f   the   ignition   and   engage   first   or  
reverse

  gear. -
 Place   a   chock   under   the   wheel  diagonally opposite the one to be
changed.
CHANGING A WHEEL
2. T

ools
The tools are stowed in a storage area
closed  by   a   flap   under   a   front   seat.
-
 
If
  necessary,   move   the   seat   forward  
to

  access   the   storage   compartment  
from

  the   rear.
-
 
Remove
  the   flap   then   take   out   the  
jack

  and   the   tool   carrier.
-
 
Remove
  the   tools   needed   from   the  
carrier

.
1.
 
Jack.
2.

 
Wheelbrace.
3.

 
Chock.
4.


Spanner for the Modutop roof bars
and

  rear   lamps.
5.
 
Alloy
  wheel   trim   removal   tool.
6.
 
T
owing   eye.
If
 
the
 
vehicle
 
is
 
fitted
 
with
 
a
 
towbar,
 
it

 
is
 
sometimes
 
necessary
 
to
 
raise
 
the

 
vehicle
 
slightly
 
to
 
make
 
it
 
easier
 
to

 
remove
 
the
 
spare
 
wheel
 
from
 
its
 
carrier

.
On
 
certain
 
types
 
of
 
ground
 
and/
or if considerable loads are being
transported, call a CITR
o
Ë
n
dealer or
a
 
qualified
 
workshop.
The
 
jack
 
and
 
tools
 
are
 
specific
 
to
 
your
 
vehicle.

 
Do
 
not
 
use
 
them
 
for
 
other
 
purposes.
Changing a wheel

173
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
3. Spare wheel
- Unscrew the bolt using the
wheelbrace until the carrier is
lowered  fully.
-
o
pen the rear doors to gain access
to
 
the
 
spare
 
wheel. -
 Detach   the   carrier   from   the   hook  and place the spare wheel near the
wheel
  to   be   changed.
QUICk HELP
8
Changing a wheel

174
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
4. Procedure
- Place  the   foot   of   the   jack   in   contact  with the ground directly below the
jacking
  point   closest   to   the   wheel   to  
be

  changed.
-
 
Extend
  the   jack   until   its   head  
comes

  into   contact   with   the   jacking  
point used; the vehicle's contact
area

A   must   be   engaged   with   the  
head

  of   the   jack.
-

Raise the vehicle until there is
sufficient

  space   between   the   wheel  
and the ground, so that


(not punctured) spare wheel can be
easily
  fitted.
-
 
Resume
  and   complete   the  
unscrewing

  of   the   wheel   bolts.
-
 
Remove
  the   bolts   and   remove   the  
wheel.
-

 Remove
 
the
 
wheel
 
trim.
-

Loosen the wheel bolts and start
unscrewing

 
them. Ensure
  that   the   jack   is   stable,   the   foot  of
  the   jack   must   be   in   contact   with   the  
ground,

  and   directly   below   the   jacking  
point

  used.
If the ground is slippery or loose, the
jack
  may   slip   or   drop   -   Risk   of   injury!
Ensure
  that   the   jack   is   positioned   only  
at

  one   of   the   jacking   points   under   the  
vehicle,

  making   sure   that   the   vehicle's  
contact surface is centred on the head
of

  the   jack.
Otherwise
  there   is   a   risk   of   damage  
to

  the   vehicle   and/or   of   the   jack  
dropping -

  Risk   of   injury!
Do
  not   extend   the   jack   until   you   have  
started unscrewing the bolts on the
wheel to be changed and have placed
the

  chock   under   the   wheel   diagonally  
opposite.
Changing a wheel

175
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
- Position the wheel on the hub and
start  tightening   the   bolts   by   hand.
-

Carry out an initial tightening of the
bolts

  using   the   wheelbrace.
5. Fitting the spare wheel
- Lower  the   vehicle   completely   by  folding
  the   jack,   then   remove   the  
jack.
-


T
ighten the bolts again using the
wheelbrace,
  tighten   them   fully  
without

  forcing   them.
-

Place the wheel to be repaired in
the

  carrier. -
 Secure   the   carrier   on   the   hook   then  raise the carrier by tightening the
bolt
  with   the   wheelbrace.
-
 
Fully
  tighten   the   bolt,   then   check  
that

  the   wheel   is   held   flat   against  
the

  floor.
If this is not the case, repeat the
operation.
n

ever go underneath a vehicle
that
  is   supported   only   by   a   jack  
(use

  a   stand).
n

ever use a power driver in place of
the
  wheelbrace.
QUICk HELP
8
Changing a wheel