2016 Citroen BERLINGO MULTISPACE light

168
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Filling
Ensure that the vehicle is parked on a flat  and   level   surface.
Pour
  the   contents   of   the   container   /  
bottle

  into   the   dedicated   tank.
After
  filling   the  
AdBlue® tank, observe the
 
following
 
procedure:
-

Switch on the ignition without
starting.
-


W

ait 10 seconds before starting the
engine.
Never
 
dispose
 
of
 
empty  
AdBlue®
containers and bottles in the
household
 
waste.
Place
 
them
 
in
 
a
 
special
 
container
 
provided

 
this
 
purpose
 
or
 
take
 
them
 
to  
your

 
dealer.
k
eep a dBlue
® out of the reach of
children,
 
in
 
its
  original   container.
n

ever transfer a dBlue
® to another
container:
 
it
 
would
 
loose
 
its
  purity.
Never
 
dilute
 
the
 
fluid
 
with
 
water.
Never
 
pour
 
the
 
fluid
 
into
 
the   Diesel   fuel  
tank.
Recommendations on storage
never store containers or bottles of adBlue® in your vehicle.
Freezing of the AdBlue
®
adBlue® freezes at about -11°C (12.2° F) and
 
deteriorates   above   25°C   (77°F).
It
 
is
 
recommended   that   containers   and  
bottles be stored in a cool area and
protected

  from   direct   sunlight.
Under
 
these   conditions,   the   fluid   can  
be

 
kept
  for   at   least   a   year.
a

dditive that has been frozen can
be used once it has thawed out in
ambient air. The
  SCR   system   includes   an  
a dBlue
® tank heater that ensures operation
  of   the   vehicle   in   normal  
conditions.
In exceptional situations, such
as

 
when
 
the
 
vehicle   is   kept   at  
temperatures

  below   -15°C   (5°F)   for   a  
long

 
period,
 
there   may   be   an   emission  
fault alert related to freezing of the a

dBlue
® additive.
Park
 
the   vehicle   in   an   area   at   a   more  
moderate

  temperature   for   a   few   hours  
until

the a dBlue
® becomes a fluid again.
The
 
emissions
 
warning   lamp   does   not  
go

 
off
 
immediately,   but   does   so   after   a  
few

 
miles
 
of
 
driving.
adBlue®

172
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
1. Parking the vehicle
- The  occupants   must   get   out   of   the  vehicle
  and   wait   in   a   safe   location.
-
 
If
  possible,   park   the   vehicle   on  
level, stable and non-slippery
ground.
-

 
Apply
  the   parking   brake,   switch  
of

f   the   ignition   and   engage   first   or  
reverse

  gear. -
 Place   a   chock   under   the   wheel  diagonally opposite the one to be
changed.
CHANGING A WHEEL
2. T

ools
The tools are stowed in a storage area
closed  by   a   flap   under   a   front   seat.
-
 
If
  necessary,   move   the   seat   forward  
to

  access   the   storage   compartment  
from

  the   rear.
-
 
Remove
  the   flap   then   take   out   the  
jack

  and   the   tool   carrier.
-
 
Remove
  the   tools   needed   from   the  
carrier

.
1.
 
Jack.
2.

 
Wheelbrace.
3.

 
Chock.
4.


Spanner for the Modutop roof bars
and

  rear   lamps.
5.
 
Alloy
  wheel   trim   removal   tool.
6.
 
T
owing   eye.
If
 
the
 
vehicle
 
is
 
fitted
 
with
 
a
 
towbar,
 
it

 
is
 
sometimes
 
necessary
 
to
 
raise
 
the

 
vehicle
 
slightly
 
to
 
make
 
it
 
easier
 
to

 
remove
 
the
 
spare
 
wheel
 
from
 
its
 
carrier

.
On
 
certain
 
types
 
of
 
ground
 
and/
or if considerable loads are being
transported, call a CITR
o
Ë
n
dealer or
a
 
qualified
 
workshop.
The
 
jack
 
and
 
tools
 
are
 
specific
 
to
 
your
 
vehicle.

 
Do
 
not
 
use
 
them
 
for
 
other
 
purposes.
Changing a wheel

180
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
CHANGING A BULB
Type A
All  glass   bulb:   pull   gently  
as

  it   is   fitted   by   pressure.
Type C
Halogen
  bulb:   release   the  
retaining

  spring   from   its  
housing. T
ype B
Bayonet
  bulb:   press  
on the bulb then turn it
anticlockwise.
T

ypes of bulb
Various
 
types
  of   bulb   are   fitted   to   your  
vehicle.
T

o
 
remove
 
them:
Type D
Light-emitting   diode  
(LED):

  for   replacement  
of

  the   daytime   running  
lamps,

  contact   a  
CITR

o Ë n dealer or a
qualified
  workshop.
Changing a bulb

182
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
3. Direction indicators
Type B,  PY21W   -   21W   (amber)
-
 
Remove
  the   cover   by   pulling   the  
flexible

  rubber   tab.
-

T
urn the bulb holder a quarter turn
anticlockwise.
-
 
Remove
  the   bulb   by   pressing   it  
lightly

  while   turning   it   anticlockwise.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing. 4. Front foglamps
T

ype C, H1 - 55W
-
 
Remove
  the   three   clips   and   the  
screw securing the wheel arch liner

,
located
  below   the   bumper.
-
 
Move
  the   wheel   arch   liner   upwards.
-
d isconnect the bulb holder
connector by pressing the tab at
the
  top.-
 
Remove
  the   bulb   holder   by  
squeezing the two clips (at top and
bottom)

  using   a   finger   and   thumb.
-
 
Replace
  the   module   (bulb   holder  
and

  bulb).
-

Carry out the operations in reverse
order

  to   fit   the   module   and   refit   the  
wheel

  arch   liner.
Changing a bulb

184
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Rear lamps
This procedure requires the use of
the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the wiring
correctly to avoid trapping the
wiring.
a

fter changing the rear direction
indicator
  bulb,   the   reinitialisation   time   is  
above

  2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-
 
Remove
  the   faulty   bulb   by  
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-
 
with
  tailgate,   pull   the   lamp   unit  
towards the centre of the vehicle,
-

 
with
  hinged   doors,   pull   the   lamp  
unit

  towards   you.
For
 
more
 
information
 
on
 
bulbs,
 
refer
 
to
 the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


T

ype B,
 
P21/5W
 
-
 
21/5W
2.

Direction indicators


T

ype B,
 
PY21W
 
-
 
21W
 
(amber)
3.

Reversing lamps


T

ype B, P21W - 21W
4.

Foglamps


T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
other
 
lamps
 
and

 
their
 
edges
 
to
 
avoid
 
damaging
 
their

 
coating
 
and
 
seals. Chapter
  9,   "Changing   a   wheel"  
section.
-


Identify the failed bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-
 
Holding
  the   lamp,   disconnect   the  
electrical

  connector.
Changing a bulb

196
Berlingo-2-VP_en_Chap09_Caract-technique_ed01-2016
ENGINE CHARACTERISTICS
The engine characteristics (capacity,
maximum  power,   maximum   power  
speed, fuel, C

o
2 emissions...) for your vehicle are given in the registration
certificate.
These characteristics correspond
to the values type-approved
on a test bed, under conditions
defined
 
in
 
European   legislation  
(Directive 1999/99/EC).
For

 
more
 
information,   refer   to   the  
manufacturer's

 
website   or   sales  
brochure

 
for
 
the
  model.   Contact  
a

 
CITROËN
 
dealer   or   a   qualified  
workshop.
WEIGHTS AND TOWED LOADS
These values, expressed in kg, can be found
  on   the   manufacturer's   VIN   plate  
or

  label.
The
  maximum   weights   and   towed  
loads for your vehicle can be found on
the

  vehicle's   registration   certificate.
The
  kerb   weight   is   equal   to   the   weight  
without

  load   +   driver   (75   kg)   +   fuel   tank  
filled

  to   90%.
The GTW and towed load values
indicated
  are   valid   up   to   a   maximum  
altitude

  of   1000   metres.  
The
  value   of  
the

  towed   load   mentioned   must   be  
reduced by 10 % for each additional
1000

  metres.
With
  load   transfer,   the   braked   trailer  
weight can be increased, on condition
that the equivalent of this load is
removed

  from   the   vehicle   so   that   the  
GTW

  is   not   exceeded. High
  ambient   temperatures  
may

  result   in   a   reduction   in   the  
performance

  of   the   vehicle   in  
order

  to   protect   the   engine.   When   the  
ambient

  temperature   is   higher   than  
37 °C,

  limit   the   towed   weight.
Towing with a lightly loaded
vehicle can adversely affect road
holding.
Towing
  a   trailer   increases   braking  
distances.
When

  towing,   the   maximum   permitted  
speed

  is   reduced   (comply   with   the  
legislation

  in   force   in   the   country).
The
  recommended   nose   weight   is  the downward force on the towball
(removable
  with   or   without   tools).
GVW: gross vehicle weight, the
maximum
  authorised   weight.
GTW:
  gross   train   weight,   the   maximum  
weight

  for   vehicle   plus   trailer.
The
  location   of   the   manufacturer's  
plate

  is   given   in   chapter   9,  
"Identification

  markings"   section.
In
  each   country,   it   is   imperative   that  
the

  maximum   towed   loads   authorised  
by

  local   legislation   are   complied  
with.

 
T
o   find   out   your   vehicle's   towing  
capacities and its gross train weight,
consult

  a   CITROËN   dealer.
Weights

Audio and Telematics
 247
Berlingo-2-VP_en_Chap10a_SMEGplus_ed01-2016
As a safety measure and because it requires sustained attention by the
driver,
  using   a   smartphone   when  
d

riving   is   prohibited.
All
  operations   must   be   done   with   the  
v

ehicle stationary .
The synchronisation of a
smartphone
  allows   applications   on   a  
s

martphone   that   are   adapted   to   the  
M

irrorLink
TM technology to be displayed
i
n
 
the
 
vehicle's   screen.
The principles and standards
are
 
constantly   evolving.   For   the  
c

ommunication   process   between   the  
s

martphone   and   the   system   to   work  
c

orrectly,
 
the   smartphone   must   be  
u

nlocked;
 
update   the   operating   system  
o

f
 
your
 
smartphone   as   well   as   the   date  
a

nd
 
time
 
in
 
the   smartphone   and   the  
s

ystem.
For
 
the
 
list
 
of   eligible   smartphones,  
c

onnect to the brand's internet website
in
 
your
 
country. As
  a   safety   measure,   applications  
c

an only be viewed with the vehicle
stationary; display is interrupted once
the   vehicle   is   moving.When connecting a smartphone to the s
ystem,   it   is   recommended   that   Bluetooth®
be
 
started
 
on
 
the
 
smartphone.
Start the application on the
smartphone   (optional,   depending  
o

n   the   smartphone   and   operating  
s

yste m).
Access
 
to
  the   different   audio   sources   remains  
a

ccessible   in   the   margin   of   the   MirrorLink
TM
display,
 
using
 
touch
 
buttons
 
in
 
the
 
upper
 
bar.
Access
 
to
 
the
 
menus
 
for
 
the
 
system
 
is
 
possible  
a

t
 
any
 
time
 
using
 
the
 
dedicated
 
buttons.
du

ring the procedure, several screen
pages relating to certain functions
are
 
displayed.
ac

cept to start and end the
connection.
Connect
 
a
 
USB
 
cable.
 
The
 
s

martphone
 
charges
 
when
 
c

onnected
 
by
 
a
 
USB
 
cable.
Press on " MirrorLink
TM" to
start the application in the
system.
on
ce connection is established, an page
is displayed with the applications already
downloaded   to   your   smartphone   and   adapted  
t

o   MirrorLink
TM technology.
If only one application has been downloaded to
the
 
smartphone,   it   starts   automatically.
MirrorLinkTM smartphone
connection
Press the end of the lighting control stalk to s
tart   voice   recognition   of   your   smartphone   via  
t

he   system.
Voice
  recognition   requires   a   compatible  
s

martphone   connected   to   the   vehicle   by  
Bl

uetooth.
Voice recognition
Please note:
-  i f   your   smartphone   is   supported,   to  
m

ake   it   "MirrorLink
TM" compatible, s
ome
 
phone
 
manufacturers  
n

evertheless invite you to first
download
 
a
 
dedicated   application.
From
 
the
 
system,
 
press   on  
"C

onnected services " to display the
primary
 pag

e.
TECHNOLOGY on BOARD
10

Audio and Telematics
251
Berlingo-2-VP_en_Chap10a_SMEGplus_ed01-2016
As a safety measure and because it requires sustained attention by the
driver,
  using   a   smartphone   when  
d

riving   is   prohibited.
All
  operations   must   be   done   with   the  
v

ehicle stationary .
As
  a   safety   measure,   applications  
c

an only be viewed with the vehicle
stationary; display is interrupted once
the
  vehicle   is   moving.
The synchronisation of a
smartphone
  allows   applications   on   a  
s

martphone   that   are   adapted   to   the  
C

arPlay
® technology to be displayed in
t
he
 
vehicle's   screen.
as

the principles and standards are
constantly
  evolving,   it   is   recommended  
t

hat
 
you
 
update   the   operating   system   of  
y

our
 
smartphone.
For
 
the
 
list   of   eligible   smartphones,  
c

onnect to the brand's internet website
in
 
your
 
country.
on c
onnecting the USB cable, the
" Telephone " function changes to
" CarPlay "   in   the   menu   carrousel.
Press on " CarPlay" to display the
CarPlay
® inter face.
P
ress on " CarPlay" to display the
CarPlay
® inter face.
C
onnect
  a   USB   cable.   The  
s

martphone   charges   when  
c

onnected   by   a   USB   cable.
Press   the   end   of   the   lighting   control   stalk   to  
s

tart   voice   recognition   of   your   smartphone   via  
t

he   system.
CarPlay® smartphone
connection
During the procedure, one or more s
creen pages relating to certain
functions
  are   displayed   on   connection.
From
  the   system,   press   on  
"
C
onnected services
" to display the
primary
 pag
e.
Connect   the   USB   cable.   The  
s

martphone   is   charged   while  
c

onnected   by   the   USB   cable.
o

r
Voice recognition
TECHNOLOGY on BOARD
10