2016 Citroen BERLINGO MULTISPACE display

158
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Levels
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
Topping up
The
 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).

164
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Good practice
While the quantity of
a
dBlue® in
the
 
additive
 
tank
 
is
 
sufficient,
 
no
 
information

 
is
 
displayed.
On
 
the
 
other
 
hand,
 
once
 
the
 
fluid
 
level drops to the quantity needed
for

 
a
 
range
 
of
 
1
 
500
 
miles
 
(2
 
400
 
km)  
driving, you are warned by dif

ferent
temporary
 
signals
 
(warning
 
lamp,
 
message,

 
audible
 
signal).
As
 
more
 
miles
 
are
 
covered,
 
these
 
signals

 
intensify
 
and
 
the
 
message  
becomes

 
permanent.
When the
a
dBlue
® tank is empty, restarting
 
becomes   impossible.
It
 
is
 
strongly
 
recommended   that   you  
do not wait for the successive alerts
before topping-up the a

dBlue
® additive,
but
 
do
 
this
 
as
 
soon
 
as
 
possible.
Filling the AdBlue® tank
For light vehicles, 5 or 10 litre
containers
 
and
 
1.89
  litre  
(1/2 US gallon)

 
bottles   are   available  
from

 
CITROËN
 
dealers,   until   they   are  
equipped

with
a
dBlue
® delivery pumps.
If
 
you
 
want
 
to
 
fill
 
the
 
AdBlue® tank yourself, ensure that you have a
suitable
 
filler
 
pipe,
 
which
 
may   or   may  
not be supplied with the additive
container

.
adBlue®

165
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
AdBlue®
Range indicators
Rules on the display of alertsFor   more   information   on   the  
displays

  and   warning   lamps,   refer  
to

  chapter   3,   "Instruments   and  
controls"

  section. Range greater than 1 500 miles
(2 400 km)
No
  information   displayed.
Once   the   1   500   miles   (2   400   km)  
threshold is reached, the URE

a

warning

  lamp   comes   on   temporarily  
and

  the   remaining   range   message   is  
displayed.
The

  alert   is   repeated   every   200   miles  
(300

  km)   until   the   next   threshold   is  
reached.
Every

  time   the   ignition   is   switched  
on, the alert is given, together with an
audible

  signal.
Remaining range less than
1
500 miles (2 400 km) and greater
than 350 miles (600 km)
Driving range
With
  the   touch   screen   tablet:
If
  the   range   is   greater   than   3   100   miles  
(5

  000   km),   a   range   value   is   not   given.
Press this button to display
the
  information.
-

select the "
d riving
assistance"
  menu,
-

select "
d iagnostic",
-
 
select
  CHECK.
d
ifferent levels of alert are triggered
according
  to   the   remaining   driving  
range threshold
Y

ou   will   be   informed   as   each   mileage  
threshold is reached and the alerts will
change

  from   temporary   to   permanent.
-

The 1st is triggered at a remaining driving
  range   of   1   500   miles  
(2
 
400
  km).
-

The 2nd is triggered at a remaining driving
  range   of   350   miles  
(600
 
km).
-
 
Up

 
to
 
0   miles,   at   which   point   it   will  
be

 
impossible   to   restart   the   engine  
after

 
a
 
stop.
CHECkS
7

 167
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
AdBlue®
Fault confirmed
In addition to the previous signals,
the  UREA
 
warning   lamp   flashes   and  
the

  remaining   range   allowed   will   be  
displayed

  in   miles   (kilometres).
The alert will be repeated every
30
seconds with an update of the
driving
  range   in   steps   of   30   miles  
(50 km).
Go

  to   a   CITROËN   dealer   or   a   qualified  
workshop

  as   soon   as   possible.
You
  risk   not   being   able   to   start   the  
engine.
Starting prevented, having
covered the 650 miles (1 100 km)
At

  each   attempt   at   starting,   the   alert   is  
activated

  and   the   message   "Emissions  
fault:

  Starting   prevented"   is   displayed.Refilling / Topping-up the
AdBlue®
Precautions to take
Use only a dBlue® that meets the ISO 22241
 
standard.
The
a
dBlue
® fluid is an urea-based solution.
This
 
fluid
 
is
 
non-flammable,   colourless  
and

 
odourless.
To
 
be
 
kept
 
in   a   cool   area.
Containers (5 or 10 litres) and
bottles (1.89 litres) of AdBlue
®
Please check the use-by date.
Read   the   instructions   on   the   label.
Ensure that you have a suitable
filler
  pipe,   which   may   or   may   not   be  
supplied

  with   the   container. In
  the   event   of   an   overflow,   wipe  
around

  the   filler   mouth   using   a  
damp

  cloth.
If any a dBlue
® fluid is split or splashed
 
on
 
to
 
you,   wash   immediately  
with cold water or wipe yourself with a
clean

 
damp
 
cloth.
If
 
the
 
fluid
 
has
 
crystallised,   clean   it   off  
using

 
a
 
sponge
 
and   hot   water.
CHECKS
7

Audio and Telematics
201
Berlingo-2-VP_en_Chap10a_SMEGplus_ed01-2016
7-inch touch screen tablet
GPS satellite navigation - Multimedia audio - Bluetooth® telephone
Contents
First steps
2 02
Steering
 
mounted
 
controls
 
2
04
Menus
205
na

vigation

206
na

vigation - Guidance
2
14
Tr a f fi c
 2

18
Radio Media

2
20
Radio
226
d

a
B (di

gital
a
u

dio Broadcasting) radio
2
28
Media


230
Settings


234
Connected services
2

42
Internet browser
2

43
MirrorLink
TM 246
C
arPlay® 250
T
elephone

254
Frequently
  asked   questions  
2
62
The
 
system
 
is
 
protected
 
in
 
such
 
a
 
way
 
that
 
it
 
will
 
only
 
operate
 
in
 
y

our
 
vehicle. As
 
a
 
safety
 
measure,
 
the
 
driver   should   only   carry   out   operations  
w

hich
 
require
 
prolonged
 
attention   while   the   vehicle   is   stationary.
The
 
display
 
of
 
an
 
energy
 
economy   mode   message   signals   that  
e

lectrical
 
systems
 
operating
 
are   going   into   standby.
Refer
 
to
 
the
 
energy
 
economy   mode   section.
TECHNOLOGY on BOARD
10

Audio and Telematics
202
Berlingo-2-VP_en_Chap10a_SMEGplus_ed01-2016
First steps
Use the buttons above the touch screen tablet
for  access   to   the   menu   carousel,   then   press   the  
v

irtual   buttons   in   the   touch   screen   tablet.
Each
  menu   is   displayed   in   one   or   two   pages  
(

primary   page   and   secondary   page).
Secondary page
Primary
 pag

eIn
  very   hot   conditions,   the   system   may  
g

o into stand-by (screen and sound
completely
  off)   for   a   minimum   period   of  
5 m

inutes.

Audio and Telematics
203
Berlingo-2-VP_en_Chap10a_SMEGplus_ed01-2016
Volume adjustment (each source is independent, i ncluding t raffic a nnouncements (

TA)   and   navigation   instructions).
Mute
  the   sound   by   pressing   simultaneously   on  
t

he   volume   increase   and   reduce   buttons.
Unmute
  the   sound   by   pressing   one   of   the   two  
v

olume
 b
uttons.Press Menu
 

to   display   the   menu  
c

arousel.
Increase   volume.
Reduce
  volume.
Selecting the audio source (depending on
version):
-
 
"

FM"
 
/
 
"DAB"
 
/
 
"AM"*
 
stations.
-
 
"

USB"
 
memory
 
stick.
-
 
S

martphone
 
via
 
MirrorLink
TM or CarPlay®.
-
T
elephone connected by Bluetooth* and
Bluetooth
 
audio
 
streaming*.
-

M

edia player connected to the auxiliary
socket
 
( jack,
 
cable
 
not
 
supplied).
-
 
J

ukebox*,
 
after
 
first
 
copying
 
audio
 
files
 
to  
t

he
 
internal
 
memory
 
of
 
the
 
system.
*
  Depending   on   equipment.
Short-cuts:
 
using
 
the
 
touch
 
buttons
 
in
 
the
 
upper
 b

and of the touch screen tablet, it is possible
to go directly to the selection of audio source,
the list of stations (or titles, depending on the
s o u r c e).
The screen is of the "resistive" type, it
is 
n
ecessary  
t
o  
p
ress  
f
irmly,  
p
articularly  
f

or   "flick"   gestures   (scrolling   through   a  
l

ist,   moving   the   map...).   A   simple   wipe  
w

ill   not   be   enough.   pressing   with   more  
t

han   one   finger   is   not   recognised.
The screen can be used when wearing
gloves.   This   technology   allows   use   at  
a

ll
 t
emperatures.
Following prolonged operation in very
high   temperatures,   the   volume   may   be
 l

imited   to   protect   the   system.   The   return   to
 n

ormal   takes   place   when   the   temperature
 i

n   the   passenger   compartment   drops.
To clean the screen, use a soft
non-abrasive cloth (spectacles cloth)
without   any   additional   product.
Do
  not   use   pointed   objects   on   the  
sc

reen.
do n

ot touch the screen with wet
hands.
TECHNOLOGY on BOARD
10

Audio and Telematics
205
Berlingo-2-VP_en_Chap10a_SMEGplus_ed01-2016
Menus
Settings
Radio Media
Navigation
Driving
Connected services Telephone
Adjust the settings for sound (balance, a
mbience,   ...),   colour   schemes   and   the   display  
(

language,   units,   date,   time,   ...).
Select an audio source, a radio station, display
photographs.
Enter navigation settings and choose a
destination.
Access
  to   the   trip   computer.
ac

tivate, deactivate or enter settings for certain
vehicle
  functions.
Connect
 
using
 
the
 
"Internet
 
browser".
op

erate certain applications on your
smartphone
 
via
 
MirrorLink
TM or CarPlay®. Connect a telephone by Bluetooth
®.ac
cess to the CarPlay® function after
connection
 
of
 
your
 
smartphone   by   USB   cable.
(Depending
 o

n
 e

quipment)
(Depending
 o

n
 e

quipment)
TECHNOLOGY on BOARD
10