2016 Citroen BERLINGO MULTISPACE parking brake

52
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Acceleration
For optimum acceleration (e.g. to overtake  another   vehicle),   simply  
press the pedal beyond the point of
resistance at the end of its travel, by
pressing

  down   firmly.
Vehicle stationary, with the
engine running
In the event of a prolonged stop with
the engine running, the gearbox
changes  automatically   to   neutral   N.
Stopping the vehicle
Before stopping the engine, put the
gear selector in position N.
In all cases, it is essential to apply
the
  parking   brake.   Check   that   the  
parking

  brake   warning   lamp   is   on   in   the  
instrument

  panel.
Before doing anything in the
engine
  compartment,   check   that  
the gear selector is in neutral

N.
Changing gear
In situations of high engine speeds
(heavy acceleration), a change
up will not occur unless the driver
operates the electronic gearbox control
paddle. Pull on the "+" control
paddle
  to   change   up.
Pull on the "-" control
paddle to change
down.
-

If the vehicle stops or reduces
speed

  (for   example   when  
approaching a stop sign),
the gearbox changes down
automatically

,   to   first   gear   if  
needed.
-


It is not necessary to release the
accelerator

  completely   during   gear  
changes.
-

a
gear change instruction is
accepted only if the engine speed
permits.
-


For safety reasons, depending on
the engine speed, a change down
may

  be   performed   automatically.
Manual mode
Changing to manual mode
Move the gear selector to M. Automatic mode Changing to automatic
mode
Move the gear selector to A.
The gearbox then operates in
automatic
 
mode,
 
without
 
any
 
action
 
on
 
your

 
part.
It constantly selects the gear that is
best
 
suited
 
to
 
the
 
following
 
conditions:
-

driving style,
-

 
road

 
profile,
-
 
optimum

 
fuel
 
consumption.
Gearbox and steering wheel

53
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
STOP & START
The Stop & Start system puts the engine
  temporarily   on   standby   -   STOP mode

  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).
The
  engine   restarts   automatically   -  
ST

ART
 
mode   -   as   soon   as   you   want   to  
move

  off.
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system
  reduces   fuel   consumption   and  
exhaust

  emissions   as   well   as   the   noise  
level

  when   stationary.
Operation
Going into engine STOP modeThe "ECO"   warning   lamp  
comes

  on   in   the   instrument  
panel and the engine goes
into

  standby:
-

with a manual gearbox
, at speeds
below
  12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with a 6-speed electronic
gearbox

,   at   speeds   below   5   mph  
(8

  km/h),   when   you   press   the   brake  
pedal or put the gear lever into
position

N. If
  your   vehicle   is   fitted   with   the   system,  
a

  time   counter   calculates   the   sum   of  
the

  periods   in   STOP
 
mode   during   a  
journey

.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With a 6-speed electronic
gearbox,   for   your   comfort   during  
parking

  manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP
 
mode   does   not   affect   the  
functionality of the vehicle, such as
braking,

  power   steering,   for   example.
n

ever refuel with the engine in
STOP
 
mode;   you   must   switch   off  the
  ignition   with   the   key.Special cases: STOP mode
unavailable
STOP
 

mode   is   not   invoked   when:
-
the vehicle is on a steep slope
(rising or fallin

g),
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded

6   mph   (10   km/h)   since   the   last  
engine

  start   using   the   key,
-  
the
  engine   is   needed   to   maintain  
a

  comfortable   temperature   in   the  
passenger

  compartment,
-  
demisting
  is   on,
-  
some
  special   conditions   (battery  
charge,

  engine   temperature,  
braking

  assistance,   ambient  temperature...)
  where   the   engine  is needed to assure control of a
system.
In this case, the
"ECO"
warning
  lamp   flashes   for   a  
few

  seconds,   then   goes   off.
This operation is perfectly normal.
REadY To Go
3
Stop & Start

56
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Starting and switching off
HILL START ASSIST
This system (also called HHC - Hill Holder
  Control),   linked   to   the   dynamic  
stability

  control   system,   makes   hill  
starts easier and is activated in the
following

  conditions:
-
 
the
  vehicle   must   be   stationary,  
engine

  running,   foot   on   the   brake,
-
 
the
  gradient   of   the   road   must   be  
steeper than 5%,
-

 
uphill,
  the   gearbox   must   be   in  
neutral or in a gear other than
reverse,
-

 
downhill,
  reverse   gear   must   be  
engaged.
The

  Hill   Start  
Assist
  system   is   a   driving  
aid.

  It   is   not   an   automatic   vehicle  
parking

  function   or   an   automatic  
parking

  brake.
Operation
With the brake pedal and clutch pedal pressed,   from   the   time   you   release  
the

  brake   pedal,   without   using   the  
parking

  brake,   you   have   approximately  
2 seconds

  to   move   off   before   the  
vehicle

  starts   to   roll   back.
During
  the   moving   off   phase,   the  
function

  is   deactivated   automatically,  
gradually

  releasing   the   braking  
pressure.

  During   this   phase,   the  
characteristic

  noise   of   mechanical  
release

  of   the   brakes   may   be   heard,  
indicating

  the   imminent   movement   of  
the

  vehicle.
Operating fault
Hill start assist is deactivated in the
following   situations:
-

when the clutch pedal is released,
-

 
when
  the   parking   brake   is   applied,
-

when the engine is switched of
f,
-
 
when
  the   engine   stalls.
If
  a   malfunction   of   the  
system

  occurs,   this  
warning

  lamp   comes   on  
accompanied

  by   an   audible  
signal

  and   confirmed   by  
a

  message   in   the   screen.   Have   the  
system

  checked   by   a   CITROËN   dealer  
or

  a   qualified   workshop.

57
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Starting and switching off
DRIVING RECOMMENDATIONS
observe the driving regulations and
remain   vigilant   whatever   the   traffic  
conditions.
Pay

  close   attention   to   the   traffic   and  
keep

  your   hands   on   the   wheel   so   that  
you

  are   ready   to   react   at   any   time   to  
any

  eventuality.
On
  a   long   journey,   a   break   every   two  
hours

  is   strongly   recommended.
In
  difficult   weather,   drive   smoothly,  
anticipate

  the   need   to   brake   and  
increase

  the   distance   from   other  
vehicles.
Driving on flooded roads
We strongly advise against driving
on  flooded   roads,   as   this   could   cause  
serious

  damage   to   the   engine   or  
gearbox, as well as to the electrical
systems

  of   your   vehicle. If you are obliged to drive through
water:
-
 
check
  that   the   depth   of   water   does  
not

  exceed   15   cm,   taking   account  
of

  waves   that   might   be   generated  
by other users,
-
 
deactivate
  the   Stop   &   Start   system,
-
drive as slowly as possible without
stallin

g.   In   all   cases,   do   not   exceed  6
  mph   (10   km/h),
- do not stop and do not switch of f
the
  engine.
On
  leaving   the   flooded   road,   as   soon  
as

  circumstances   allow,   make   several  
light

  brake   applications   to   dry   the   brake  
discs

  and   pads.
If in doubt on the state of your vehicle,
contact a CITR
o Ë n dealer or a
qualified
  workshop.Never
  drive   with   the   parking   brake  
applied

  -   Risk   of   overheating   and  
damage

  to   the   braking   system!
Risk   of   fire!
As   the   exhaust   system   of   your   vehicle  
is

  very   hot,   even   several   minutes   after  
switching

  off   the   engine,   do   not   park  
or run the engine over areas where
inflammable

  substances   and   materials  
are

  present:   grass,   leaves,   etc...)
n

ever leave a vehicle
unsupervised with the engine
running.   If   you   have   to   leave  your vehicle with the engine running,
apply
  the   parking   brake   and   put   the  
gearbox into neutral or position

N or P,
depending
  on   the   type   of   gearbox.
Important!
REadY To Go
3

11 4
Berlingo-2-VP_en_Chap05_Securite_ed01-2016
HAZARD WARNING LAMPS
H
ORN
Press the centre of the steering wheel.
PARKING BRAKE
Applying
Pull the parking brake lever up to immobilise
  your   vehicle.
Check
  that   the   parking   brake   is   applied  
firmly

  before   leaving   the   vehicle.Pull
  on   the   parking   brake   lever,   only
with the vehicle stationary.
In the exceptional case of use of the
parking
  brake   when   the   vehicle   is  
moving,

  apply   the   brake   by   pulling  
gently

  to   avoid   locking   the   rear   wheels  
(risk

  of   skidding).
Press this button, the direction
indicators
 
flash.
They
 
can
 
operate
 
with
 
the
 
ignition
 
off.
The
 
hazard
 
warning
 
lamps
 
should
 
only
 
be used in dangerous situations, when
stopping

 
in
 
an
 
emergency
 
or
 
when
 
driving

 
in
 
unusual
 
conditions.
When
  parking   on   a   slope,   direct   your  
wheels

  towards   the   pavement   and   pull  
the

  parking   brake   lever   up.
There is no advantage in engaging
a
  gear   after   parking   the   vehicle,  
particularly

  if   the   vehicle   is   loaded.
If the parking brake is still on or has not been released properly, this is
indicated
  by   this   warning   lamp   which
 comes

  on   in   the   instrument   panel.
Automatic operation of hazard
warning lamps
When braking in an emergency, depending on the force of deceleration,
the  hazard   warning   lamps   come  
on

  automatically.  
They
  switch   off  
automatically

  the   first   time   you  
accelerate.
It

  is   also   possible   to   switch   them   off   by  
pressing

  the   switch   on   the   dashboard.Releasing
Pull the lever up slightly and press the
button  to   lower   the   parking   brake   lever.
driving safely

 149
Towing a trailer
Berlingo-2-VP_en_Chap06_accessoire_ed01-2016
Good Practice
In certain cases of particularly arduous
use  (towing   the   maximum   load   up   a  
steep

  slope   in   high   temperatures),   the  
engine

  automatically   limits   its   power.  
In this case, the air conditioning is
automatically

  cut   off   to   save   engine  
power

.
Tyres
Check
  the   tyre   pressures   of   the   towing  
vehicle and of the trailer

, observing the
recommended
  pressures.
Chapter
  7,   "Levels"   section.
If
  the   coolant   temperature  
warning

  lamp   comes   on,   stop  
the vehicle and switch of

f the
engine
  as   soon   as   possible.Brakes
Towing
  increases   the   braking   distance.  Drive
  at   a   moderate   speed,   change  
down

  early   and   brake   gradually.
Towbar
We recommend the use of genuine CITRo Ë n towbars and their wiring
harnesses, which have been tested
and
  approved   from   the   design   stage   of  
your vehicle, and that you entrust the
fitting

  of   this   equipment   to   a   CITROËN  
dealer

.
If
  this   equipment   is   not   fitted   by   a  
CITROËN

  dealer,   it   is   imperative   that  
it

  is   fitted   using   the   electrical   pre-
equipment
  installed   at   the   rear   of   the  
vehicle and in accordance with the
manufacturer's

  instructions.
In accordance with the general
instructions
  a   reminder   of   which   has  
been given above, we draw your
attention

  to   the   risk   associated   with  
fitting

  a   towbar   or   electrical   accessory  
not

  recommended   by   CITROËN.  
Fitting

  such   equipment   could   result   in  
the failure of your vehicle's electronic
system.

  Please   obtain   information   from  
the

  Manufacturer   before   fitting   this   type  
of

  equipment.
Side wind
Sensitivity
 
to
 
side
 
wind
 
is
 
increased.
 
Drive

 
smoothly
 
and
 
at
 
a
 
moderate
 
speed.
ABS/DSC
The

 
ABS

 
or
 
DSC
 
systems
 
only
 
control
 
the

 
vehicle,
 
not
 
the
 
trailer
 
or
 
caravan.
Parking sensors
The
 
rear
 
parking
 
sensors
 
system
 
does
 
not

 
function
 
while
 
the
 
vehicle
 
is
 
towing.
Chapter
 
9,
 
"Identification
 
markings"

 
section.
ACCESSORIES
6

 159
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Checks
CHECKS
Carbon filter and passenger compartment filterParticle filter (Diesel)
Maintenance of the particle filter must be  carried   out   by   a   CITROËN   dealer.
o

n acceleration after the vehicle has
been running for a prolonged period
at
  very   low   speed   or   at   idle,   you   may,  
in

  exceptional   circumstances,   notice  
the

  emission   of   water   vapour   at   the  
exhaust.

 
This
  water   vapour   does   not  
have any adverse ef

fect on vehicle
handling
  or   the   environment.
Battery
At the start of summer or winter, have your  battery   checked   by   a   CITROËN  
dealer

  or   a   qualified   workshop.
Brake pads
Brake pad wear depends on the style of driving, in particular for vehicles
which are used in town, over short
distances.
  It   may   be   necessary   to  
check

  the   thickness   of   the   pads,   even  
between

  services.
Unless
  there   is   a   leak   on   the   circuit,   a  
drop

  in   the   brake   fluid   level   indicates  
that

  the   brake   pads   are   worn.
Brake disc / drum wear
For information on checking the brake disc  /   drum   wear,   contact   a   CITROËN  
dealer

.
Parking brake
Where the parking brake travel is too great or there is a reduction in the
performance
  of   the   system,   the   parking
 brake

  should   be   adjusted,   even   between
 services.
Have

  the   system   checked   by   a   CITROËN
 dealer

  or   a   qualified   workshop.
Oil filter
Change the filter regularly in accordance  with   the   manufacturer's  
servicing

  schedule.
An
 
access
 
flap
 
allows
 
replacement
 
of
 
the

 
filters.
The
 
carbon
 
filter
 
permits
 
continuous
 
and

 
effective
 
filtering
 
of
 
dust.
If
 
the
 
passenger
 
compartment
 
filter
 
becomes

 
blocked,
 
this
 
may
 
reduce
 
the
 performance
 
of
 
the
 
air
 
conditioning
 system
 
and
 
generate
 
unpleasant
 odours.
W
e
 
recommend
 
the
 
use
 
of
 
a
 
combined
 
passenger

 
compartment
 
filter.
 
By
 
means

 
of
 
its
 
second
 
special
 
active
 
filter

,
 
it
 
contributes
 
to
 
the
 
purification
 
of the air breathed by the occupants
and the cleanness of the passenger
compartment

 
(reduction
 
of
 
allergic
 
symptoms,

 
unpleasant
 
odours
 
and
 
greasy

 
deposits).
Refer to theservicing and warranty
booklet
 
for
 
the
 
replacement
 
interval
 
for
 
these

 
components. Depending
  on   the   environment   (dusty  
atmosphere...)

  and   the   use   of   the  
vehicle

  (urban   driving...),   change   them  
twice

  as   often   if   necessary.
CHECKS
7

172
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
1. Parking the vehicle
- The  occupants   must   get   out   of   the  vehicle
  and   wait   in   a   safe   location.
-
 
If
  possible,   park   the   vehicle   on  
level, stable and non-slippery
ground.
-

 
Apply
  the   parking   brake,   switch  
of

f   the   ignition   and   engage   first   or  
reverse

  gear. -
 Place   a   chock   under   the   wheel  diagonally opposite the one to be
changed.
CHANGING A WHEEL
2. T

ools
The tools are stowed in a storage area
closed  by   a   flap   under   a   front   seat.
-
 
If
  necessary,   move   the   seat   forward  
to

  access   the   storage   compartment  
from

  the   rear.
-
 
Remove
  the   flap   then   take   out   the  
jack

  and   the   tool   carrier.
-
 
Remove
  the   tools   needed   from   the  
carrier

.
1.
 
Jack.
2.

 
Wheelbrace.
3.

 
Chock.
4.


Spanner for the Modutop roof bars
and

  rear   lamps.
5.
 
Alloy
  wheel   trim   removal   tool.
6.
 
T
owing   eye.
If
 
the
 
vehicle
 
is
 
fitted
 
with
 
a
 
towbar,
 
it

 
is
 
sometimes
 
necessary
 
to
 
raise
 
the

 
vehicle
 
slightly
 
to
 
make
 
it
 
easier
 
to

 
remove
 
the
 
spare
 
wheel
 
from
 
its
 
carrier

.
On
 
certain
 
types
 
of
 
ground
 
and/
or if considerable loads are being
transported, call a CITR
o
Ë
n
dealer or
a
 
qualified
 
workshop.
The
 
jack
 
and
 
tools
 
are
 
specific
 
to
 
your
 
vehicle.

 
Do
 
not
 
use
 
them
 
for
 
other
 
purposes.
Changing a wheel