2016 Citroen BERLINGO MULTISPACE cruise control

65
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
Selecting the functionFirst activation /
Programming a
speed Temporarily exceeding the
speed setting
Deactivation (off)
- Press this button or
the  brake   or   clutch  
pedal.
Reactivation
- Following deactivation of the cruise
control,  press   this   button.
Your vehicle will return to the last
programmed
  speed.
Alternatively,
  you   can   repeat   the   "first  
activation"

  procedure.
It is possible to accelerate and drive
momentarily
 
at
 
a
 
speed
 
greater
 
than
 
the

 
programmed
 
speed
 
setting.
 
The

 
value

 
programmed
 
flashes.
When the accelerator pedal is
released, the vehicle will return to the
programmed
 
speed.
-

Reach the chosen speed by
pressing

 
the
 
accelerator.
-

Press the

SET - or SET +
 
button.
This
 
programmes/activates
 
the
 
speed
 
setting

 
and
 
the
 
vehicle
 
will
 
maintain
 
this

 
speed.
-

Place the switch in the

CRUISE
position.
 
The

 
cruise
 
control
 
is
 
selected but is not yet active and
no

 
speed
 
has
 
been
 
programmed.
Steering mounted controls
EaSE oF USE and CoMFoRT
4

66
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
Changing the
programmed speedSwitching the system off
Operating fault Cancelling the programmed
speed setting
When the vehicle becomes stationary, after switching of
f the ignition, the
system
  no   longer   memorises   a   speed.
There
 
are
 
two
 
methods
 
of
 
memorising
 
a speed

higher
 
than
 
the
 
previous
 
one:
-
Place the dial in position
0 or switch
off the ignition to switch everything
off.
Good practice
Without using the accelerator
-

Press the
SET +   button.
A brief   press   increases   the   speed   by   1   mph   (km/h).
A maintained   press   increases   the   speed   in steps
  of   5   mph   (km/h).
Using the accelerator
-
 
Exceed
  the   memorised   speed   until  
the speed required is reached,
-


Press the
SET + or SET -   button.
To
  memorise   a   speed   lower than the
previous
  one:
-

Press the
SET -   button.
a brief press decreases the speed by


1
  mph   (km/h).
A
 

maintained   press   decreases   the  
speed

  in   steps   of   5   mph   (km/h).The
  programmed   speed   setting   is  
cleared

  and   replaced   by   three   dashes.  
Contact a CITR

o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked.When

  changing   the   programmed  
speed

  setting   by   means   of   a  
maintained

  press,   pay   attention   as  
the speed can increase or decrease
rapidly

.
d

o not use the cruise control on
slippery   roads   or   in   heavy   traffic.
In the event of a steep slope, the cruise
control   cannot   prevent   the   vehicle   from  
exceeding

  the   programmed   speed  
setting.
In any event, the cruise control cannot
replace the need to observe the speed
limits

  and   the   need   for   vigilance   on   the  
part

  of   the   driver.
It   is   advisable   to   keep   your   feet   near  
the

  pedals.
To   avoid   any   jamming   under   the  
pedals:
-

 
ensure
  that   the   mat   and   its   fixings  
on

  the   floor   are   positioned   correctly,
-  
never
  place   one   mat   on   top   of  another
.
Steering mounted controls