2016 Citroen BERLINGO MULTISPACE battery

48
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
Trip recorder zero
reset button
after this operation, if you wish to
disconnect   the   battery,   lock   the  
vehicle

  and   wait   for   at   least   five  
minutes,

  otherwise   the   zero   re-set   will  
not

 
be   registered.
Engine oil level indicator
depending on your vehicle's engine,
when the ignition is switched on,
the engine oil level is indicated for
a few
seconds, after the service
information. Oil level
correct
Low oil level
Flashing of "OIL",
linked
  with   the  
service

  warning   lamp,  
accompanied

  by   an  
audible

  signal   and   a   message   in   the  
screen, indicates a low oil level which
could

  damage   the   engine.
If   the   low   oil   level   is   confirmed   by   a  
check

  using   the   dipstick,   it   is   essential  
that

  the   level   is   topped   up.
Oil level gauge
fault
Flashing of "OIL--"
indicates a
malfunction   of   the  
engine

  oil   level   indicator.   Contact  
a

  CITROËN   dealer   or   a   qualified  
workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been of
f for
more
  than   30   minutes.Dipstick
A
  =   maximum,   never   exceed  
this level as a surplus of oil
may

  damage   the   engine.
Contact a CITR o Ë n dealer
or   a   qualified   workshop  
without

  delay.
B  
=
 
minimum,
 
top
 
up
 
the
 
level
 
via

  the   oil   filler   cap,   using   the  
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
  and   controls.  
When the lighting reaches
the

  minimum  
(or
 
maximum)   setting,   release   the  
button then press it again to increase
(or

 
reduce)
 
the   brightness.
a

s soon as the lighting is of the
required
 
brightness,   release   the   button.
Zero reset
Your CITROËN dealer or a qualified workshop  carries   out   this   operation  
after

  each   service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-

 
switch
  on   the   ignition.
The
  display   begins   a   countdown.
When the display shows "=0", release
the
  button;   the   spanner   disappears.

53
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
STOP & START
The Stop & Start system puts the engine
  temporarily   on   standby   -   STOP mode

  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).
The
  engine   restarts   automatically   -  
ST

ART
 
mode   -   as   soon   as   you   want   to  
move

  off.
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system
  reduces   fuel   consumption   and  
exhaust

  emissions   as   well   as   the   noise  
level

  when   stationary.
Operation
Going into engine STOP modeThe "ECO"   warning   lamp  
comes

  on   in   the   instrument  
panel and the engine goes
into

  standby:
-

with a manual gearbox
, at speeds
below
  12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with a 6-speed electronic
gearbox

,   at   speeds   below   5   mph  
(8

  km/h),   when   you   press   the   brake  
pedal or put the gear lever into
position

N. If
  your   vehicle   is   fitted   with   the   system,  
a

  time   counter   calculates   the   sum   of  
the

  periods   in   STOP
 
mode   during   a  
journey

.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With a 6-speed electronic
gearbox,   for   your   comfort   during  
parking

  manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP
 
mode   does   not   affect   the  
functionality of the vehicle, such as
braking,

  power   steering,   for   example.
n

ever refuel with the engine in
STOP
 
mode;   you   must   switch   off  the
  ignition   with   the   key.Special cases: STOP mode
unavailable
STOP
 

mode   is   not   invoked   when:
-
the vehicle is on a steep slope
(rising or fallin

g),
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded

6   mph   (10   km/h)   since   the   last  
engine

  start   using   the   key,
-  
the
  engine   is   needed   to   maintain  
a

  comfortable   temperature   in   the  
passenger

  compartment,
-  
demisting
  is   on,
-  
some
  special   conditions   (battery  
charge,

  engine   temperature,  
braking

  assistance,   ambient  temperature...)
  where   the   engine  is needed to assure control of a
system.
In this case, the
"ECO"
warning
  lamp   flashes   for   a  
few

  seconds,   then   goes   off.
This operation is perfectly normal.
REadY To Go
3
Stop & Start

54
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Going into engine START modeThe "ECO"
  warning   lamp
 goes

  off   and   the   engine   starts:
-

with a manual gearbox
, when you
fully depress the clutch pedal,
-

with a 6-speed electronic
gearbox

:
●
 
gear
  lever   in   position   A or M,
when
  you   release   the   brake  
pedal,
●

 
or
  gear   lever   in   position   N and
the
  brake   pedal   released,   when  
you

  move   the   gear   lever   to  
position

A or M,
●
 
or
  when   you   engage   reverse  
gear

.
With
  a   manual   gearbox   in   STOP
 mode,

  if   a   gear   is   engaged   without  
fully depressing the clutch pedal, a
warning

  lamp   comes   on   or   a   message  
is

  displayed   asking   you   to   depress   the  
clutch

  pedal   to   restart   the   engine.
Special cases: START invoked
automatically
For
  your   safety   and   comfort,   START
 
is  
invoked

  automatically   when:
-

you open the driver's door
,
-

you unfasten the driver's seat belt, In this case the

"ECO"
warning
  lamp   flashes   for   few  
seconds,

  then   goes   off.
This operation is perfectly normal.
Deactivation
In certain circumstances, such as the need to   maintain   a   comfortable   temperature   in the

  passenger   compartment,   it   may   be
 preferable

  to   deactivate   Stop   &   Start.
At any time, press the "ECO
OFF" switch to deactivate the
system.
This
 
is
 
confirmed   by   the   switch   warning  
lamp

 
coming   on   accompanied   by   a  
message

  in   the   screen.
If
 
the
 
system   has   been   deactivated  
in

 
STOP
 

mode,   the   engine   restarts  
immediately

.
Reactivation
Press the "ECO OFF" switch again.
The   system   is   active   again;   this   is  
confirmed

  by   the   switch   warning  
lamp

  going   off   and   a   message   in   the  
instrument

  panel.
The
  system   is   reactivated  
automatically

  at   every   new   start  
using

  the   key.
Operating fault
In the event of a malfunction with  the   system,   the   "ECO
OFF"
  switch   warning   lamp  
flashes,

  then   comes   on  
continuously

.
This
  system   requires   a   specific  
battery

  with   a   special   specification  
and technology (reference
numbers

  available   from   a   CITROËN  
dealer

 
or
  a   qualified   workshop).
Fitting a battery not listed by
CITROËN introduces
  the   risk   of  
malfunction

  of   the   system.
have
 
it
 
checked   by   a   CITROËN   dealer  
or

 
a
 
qualified   workshop.
In
 
the
 
event   of   a   fault   in   STOP
 
mode,  
the

 
vehicle   may   stall.  
All
  of   the   warning  
lamps

 
in
 
the   instrument   panel   come  
on.

 
It
 
is
 
then   necessary   to   switch   off  
the ignition and start the engine again
using

 
the
  key.
-

the speed of the vehicle exceeds
15

 
mph
 
(25
 
km/h)
 
with
 
a
 
manual
 
gearbox

 
or
 
7
 
mph
 
(11
 
km/h)
 
with
 
the 6-speed electronic gearbox
system,
-
 some

 
special
 
conditions
 
(battery
 charge,

 
engine
 
temperature,
 
braking
 assistance,

 
ambient
 
temperature...)
 where the engine is needed to


assure
 
control
 
of
 
a
 
system.
Stop & Start

55
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
The Stop & Start system requires  a   battery   of   specific  
characteristics.

 
All
  work   on   this  
type

  of   battery   must   be   done   only  
by

 
a
  CITROËN   dealer   or   a   qualified  
workshop.
For

 
more   information   on   the   12   V  
battery

,   refer   to   "Battery"   in   section   8.
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If  the   temperature   is   high  
enough,

  the   warning   lamp  
comes

  on   for   less   than  
one

second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp
 
to
 
go   off   then   operate   the   starter  
(Starting position) until the engine
starts.Door or bonnet open


warning lamp
If this comes on, a door or the bonnet is   not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (
d iesel engine) to
return
  to   idle.
d

o not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system
 
to
 
avoid
 
the
 
risk
 
of
 
injury
 
related

 
to
 
an
 
automatic
 
change
 
to
 
ST

ART
 

mode.
Driving on flooded roads
Before
 
driving
 
through
 
a
 
flooded
 
road,
 
it

 
is
 
strongly
 
recommended
 
that
 
you
 
deactivate

 
the
 
Stop
 
&
 
Start
 
system.
For
 
more
 
advice
 
on
 
driving,
 
particularly
 
on

 
flooded
 
roads,
 
refer
 
to
 
the
 
corresponding

 
section.
REadY To Go
3
Stop & Start

 59
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
LED DAYTIME RUNNING LAMPS
Rear foglamps (amber, 
2nd rotation of the ring
forwards).
Front
  foglamps   (green,  
1st

rotation of the ring
forwards). Rotate this ring forwards
to switch on and
rearwards   to   switch   off.
Their   state   is   confirmed   by  
the

  warning   lamps   in   the  
instrument

  panel. Do   not   forget   to   switch   them   off  
when

  they   are   no   longer   needed.
Operation   of   the   automatic   illumination  
of

  headlamps   switches   off   the   rear  
foglamps,

  but   the   front   foglamps  
remain

  on.
To switch off the front and
rear   foglamps,   turn   the  
ring rearwards twice in
succession.
Automatic illumination of headlamps
In foggy weather or in snow,
the  sunshine   sensor   may   detect  
sufficient

  light.
a

s a consequence, the lighting
will
  not   come   on   automatically.   If  
necessary

,   you   must   switch   on   the  
dipped

  beam   headlamps   manually.
d

o not cover the sunshine sensor
located on the windscreen, behind
the
 
mirror.   It   is   used   for   the   automatic  
illu

mination   of   headlamps   and   for   the  
automatic

  rain   sensitive   wipers.
Activation The
  sidelamps  
and

  dipped   beam  
headlamps

  switch  
on

  automatically   if  
the light is poor

, or
during operation of the windscreen
wipers.  
They
  switch   off   as   soon   as   the  
light

  becomes   bright   enough   or   the  
windscreen

  wipers   stop.
o

n starting the vehicle, in daylight the
LED
 
daytime
 
running
 
lamps
 
come
 
on
 
automatically

.
If
 
the
 
sidelamps
 
and
 
headlamps
 
are
 
switched

 
on
 
manually
 
or
 
automatically,
 
the

 
daytime
 
running
 
lamps
 
go
 
off.
Programming
For countries where exterior lighting by
day   is   not   a   legal   requirement,   you   can  
activate or deactivate the function via
the

  configuration   menu.
If the user does not operate any
equipment
 
for
 
30
 
minutes,
 
the
 
Economy

 
mode
 
engages
 
to
 
avoid
 
discharging

 
the
 
battery.
 
Electrical
 
functions are put on standby and the
battery

 
warning
 
lamp
 
flashes.
Sidelamp
 
operation
 
is
 
not
 
affected
 
by
 
Economy

 
mode.
In clear weather or in rain, both day
and  night,   rear   foglamps   dazzle   and  
their

  use   is   prohibited.
Refer to chapter 8, "Battery
section".
Front and rear foglamps
They
 
operate
 
with
 
the
 
sidelamps
 
and
 
dipped

 
beam
 
headlamps.
Turn the ring to the AUTO  position.  The activation of this function is
accompanied
  by   a   message   in   the  
screen.
Deactivation
T

urn   the   ring   forwards   or   rearwards.  
The deactivation of this function is
accompanied

  by   a   message   in   the  
screen. This
  function   is   not   compatible   with  
daytime

  running   lamps.
Steering mounted controls
EASE OF USE and COMFORT
4

106
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
12 volt socket (120 W max)
It is advisable to limit the use of this socket  to   avoid   discharging   the   battery.
Protective net
Open the cover located in the hook support.
Fix the top of the net in the notches,
having
  first   turned   the   bar   1/4   of   a   turn.
Ensure that the end of the bar engages
correctly
  in   the   metal   part   of   its  
location.
Fix the straps in the locations provided
on

  the   floor.
Tighten
  the   net   using   the   straps.
Stowing rings
Use these rings to secure loads on the
floor.
The connection of an electrical
device not approved by CITR
o
Ë
n
,
such
 
as
 
a
 
USB
 
charger,
 
may
 
adversely af

fect the operation of
vehicle
 
electrical
 
systems,
 
causing
 
faults such as poor telephone reception
or interference with displays in the
screens.
Practical information

 107
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
REAR FITTINGS
(7 SEAT VERSION )
Cup holder
Any liquid carried in a cup (mug or other) on board which could spill,
presents   a   risk.
Take
  care.
12 volt socket (120 W max)
It is advisable to limit the use of this socket   to   avoid   discharging   the   battery.
Stowing rings
Use the stowing rings on the floor to secure  and   retain   your   loads   firmly.
The
  seat   belt   anchorages   must   not   be  
used

  for   this   purpose.
 It

  is   recommended   that   the   load   is  
immobilised

  by   securing   it   firmly  
using the stowing rings on the
floor

.
EASE OF USE and COMFORT
4
Practical information

11 3
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
ELECTRIC WINDOWS
Lower the window fully, then raise it, it
will  rise   in   steps   of   a   few   centimetres  
each

  time   the   control   is   pressed.  
Repeat the operation until the window
is

  fully   closed.
Continue to press the control for at
least one second after the window
closed
  position   has   been   reached.
The safety anti-pinch does not operate
during
  these   operations.
Safety anti-pinch
When the window rises and meets an obstacle,  it   stops   and   partially   lowers.
Manual mode
This mode is available depending  on   equipment;   it   is  
identified

  by   this   symbol   on   the  
control

  in   question.
Good practice
If the electric windows meet an obstacle  during   operation,   you   must  
reverse

  the   movement   of   the   window.  
T

o  
do
 
this,
 
press
 
the
 
control
 
concerned.
When the driver operates the
passenger electric window controls,
they

  must   ensure   that   no   one   is  
preventing correct closing of the
windows.
The

  driver   must   ensure   that   the  
passengers use the electric windows
correctly

.
Be aware of children when operating
the
  windows.
Following
  several   consecutive   closing/
opening operations of the electric
window
  control,   a   protection   system  
is triggered which only allows closing
of

  the   window.  
After
  closing,   wait  
approximately

  40   minutes.   Once   this  
time

  has   elapsed,   the   control   becomes  
operational

  again.
1.
d
river's side
2.

Passenger's side
Reinitialisation
Following reconnection of the battery,
or   in   the   event   of   a   malfunction,   the  
safety

  anti-pinch   function   must   be  
reinitialised. The electrical functions of the electric
windows
  are   deactivated:
-  
approximately
  45   seconds   after   the  
ignition is switched of

f,
-
after one of the front doors is
opened,

  if   the   ignition   is   off.
There
 
are
 
two
 
operating
 
modes:
Press or pull the control, without
passing
 
the
 
point
 
of
 
resistance.
The window stops when you release
the
 
control.
One-touch mode
Press or pull the control, beyond the
point
  of   resistance.
The window opens or closes fully when
the
  control   is   released.
Pressing or pulling the control again
stops
  the   movement   of   the   window.
EaSE oF USE and CoMFoRT
4
Mirrors and windows