2016 Citroen BERLINGO MULTISPACE ESP

3
Berlingo-2-VP_en_Chap00a_Sommaire_ed01-2016
Corresponds to
a left hand drive
vehicle.Corresponds to a
right hand drive
vehicle.
10.
201-286
TECHNOLOGY

on
BOARD
6.
148-152
ACCESSORIES
7

.
153-168
CHECKS 8

.
169-191
QUICK HELP
7-inch touch 
screen tablet 201
Audio
  system  
269
T

owing a trailer
148
T
owbar with detachable swan
 
neck
 
towball
 
150o

ther accessories

152
o

pening the bonnet

154
Petrol engine


155d

iesel engine

156
Levels

 
157
Checks

 
159
Fuel


161
Fuel cut-off

162
Diesel

 
priming
 
pump
 
162
BlueH

d
i and
a
dBlue
® 163 Battery  
169
T
emporary   puncture  
repair   kit  
171
Changing
  a   wheel  
172Removable snow screen 178
Snow
 
chains
 179
Changing a bulb

180 a fuse


186 a

 
wiper
 
blade
 
190
Being

 
towed
 
191
9.
192-200
TECHNICAL


D ATA
Dimensions 192
Engines  196
W
eights  
196
Identification

 
markings
 
200The "T

echnology on board"
section presents the new
audio/navigation   systems.
Contents
ConTEnTS

37
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
Warning lamp in the
screen is
indicates Solution - action
Cruise
control on.
cruise
 
control
 
selected. Manual
 
selection.
Chapter
 
4,
 
"Steering
 
mounted   controls"   section.
Speed limiter on.speed
 
limiter
 
selected. Manual
 
selection.
Chapter
 
4,
 
"Steering
 
mounted   controls"   section.
Gear shift
indicator on.a
 
recommendation
 
independent of the type and
density

 
of
 
traffic. To
 
reduce
 
fuel
 
consumption,   change   to   an  
appropriate

 
gear
 
with
  a   manual   gearbox.  
The driver retains responsibility to follow this
indication

 
or
 
not.
Diesel pre-
heating on.climatic
 
conditions
 
requiring
 
pre-heating. W

ait
 
until
 
the
 
warning
  lamp   goes   off   before  
operating

 
the
 
starter.
Presence of
water in the
Diesel filter
on and
accompanied by
  a   message   in
 the

  screen.
water in the Diesel filter. Have   the   filter   bled   by   a   CITROËN   dealer   or   a  qualified
  workshop   without   delay.
Chapter   7,   "Checks"   section.
According
  to   country.
Service
spanner on.that a service will be due
shortly. Refer
  to   the   list   of   checks   in   the   maintenance   and  
warranty

  guide.
Have the service carried out by a CITR
o Ë n
dealer
  or   a   qualified   workshop.
Time flashing. adjustment
  of   the   time.Use
  the   left-hand   button   on   the   instrument   panel.
Chapter
  3,   "Instruments   and   controls"   section.
REadY To Go
3

43
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
UNDER-INFLATION DETECTION WITH REINITIALISATION
System which automatically checks the pressures  of   the   tyres   while   driving.
The
  system   monitors   the   pressures  
in the four tyres, once the vehicle is
moving.
It

  compares   the   information   given   by  
the four wheel speed sensors with
reference values, which must be
reinitialised every time the tyre
pressures are adjusted or a wheel
changed

.
The
  system   triggers   an   alert   as   soon  
as

  it   detects   a   drop   in   the   inflation  
pressure

  of   one   or   more   tyres. The   under-inflation   detection  system
  does   not   replace   the   need  
for vigilance on the part of the
driver

.
This
  system   does   not   avoid   the   need   to  
check

  the   tyre   pressures   (including   the  
spare

  wheel)   every   month   as   well   as  
before

  a   long   journey.
Driving
  with   under-inflated   tyres  
impairs

  road   holding,   extends   braking  
distances

  and   causes   premature  
tyre wear

, particularly under arduous
condition (high loading, high speed,
long
  journey).
Driving
  with   under-inflated   tyres  
increases

  fuel   consumption.The
  inflation   pressures   defined   for  your vehicle can be found on the
tyre
  pressure   label.
For
  more   information   on   the  
identification

  markings,   refer   to   the  
corresponding

  section.
Tyre
  pressures   should   be   checked  
when the tyres are "cold" (vehicle
stopped

  for   1   hour   or   after   a   journey   of  
less

  than   6   miles   (10   km)   at   moderate  
speeds).
Otherwise

  (when   hot),   add   0.3   bar   to  
the

  pressures   shown   on   the   label.
REadY To Go
3

50
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
The information appears in  the   instrument   panel  
in

  the   form   of   an   arrow.   It  
may

  be   accompanied   by   a  
recommended

  gear.
The
  system   adapts   its   gear  
change

  recommendation  
according to the driving conditions
(slope,

 
load, ...)   and   the   demands  
of the driver (power

, acceleration,
braking, ...).
The
 
system   never   suggests:
-
 
engaging
  first   gear,
-
 
engaging
  reverse   gear.
With
 
an
 
electronic
 
gearbox,
 
the
 
system
 
is

 
only
 
active
 
in
 
manual
 
mode.
GEAR SHIFT INDICATOR
depending on the driving situation and
your   vehicle's   equipment,   the   system  
may

  advise   you   to   skip   one   (or   more)  
gear(s).

 
Y
ou   can   follow   this   instruction  
without

  engaging   the   intermediate  
gears.
The

  gear   engagement  
recommendations

  must   not   be  
considered

  compulsory.  
This
  is  
because

  the   configuration   of   the   road,  
the

  traffic   density   and   safety   remain  
determining

  factors   when   choosing  
the

  best   gear.  
Therefore,
  the   driver  
remains

  responsible   for   deciding  
whether or not to follow the indications
given.
This

  function   cannot   be   deactivated.
System
 
which
 
reduces
 
fuel
 
consumption

 
by
 
recommending
 
the
 
most

 
appropriate
 
gear.
Gearbox and steering wheel

55
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
The Stop & Start system requires  a   battery   of   specific  
characteristics.

 
All
  work   on   this  
type

  of   battery   must   be   done   only  
by

 
a
  CITROËN   dealer   or   a   qualified  
workshop.
For

 
more   information   on   the   12   V  
battery

,   refer   to   "Battery"   in   section   8.
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If  the   temperature   is   high  
enough,

  the   warning   lamp  
comes

  on   for   less   than  
one

second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp
 
to
 
go   off   then   operate   the   starter  
(Starting position) until the engine
starts.Door or bonnet open


warning lamp
If this comes on, a door or the bonnet is   not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (
d iesel engine) to
return
  to   idle.
d

o not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system
 
to
 
avoid
 
the
 
risk
 
of
 
injury
 
related

 
to
 
an
 
automatic
 
change
 
to
 
ST

ART
 

mode.
Driving on flooded roads
Before
 
driving
 
through
 
a
 
flooded
 
road,
 
it

 
is
 
strongly
 
recommended
 
that
 
you
 
deactivate

 
the
 
Stop
 
&
 
Start
 
system.
For
 
more
 
advice
 
on
 
driving,
 
particularly
 
on

 
flooded
 
roads,
 
refer
 
to
 
the
 
corresponding

 
section.
REadY To Go
3
Stop & Start

58
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
DIRECTION INDICATORS
"Motorway" function
Press  the   control   up   or   down   to   flash  
the corresponding direction indicator
three

  times.
LIGHTING
Left: downwards passing the point  of   resistance.
Right:
  upwards   passing   the  
point

  of   resistance.
Front and rear lighting
Lighting off
Automatic
  illumination   of  
headlamps
SidelampsDipped

  beam   (green)
Dipped beam/main beam change
Pull
 
the
 
stalk   fully   towards   you.
Lighting-on audible warning
o

n switching off the ignition, all of the
lamps
 
turn   off,   except   dipped   beam   if  
automatic

  guide-me-home   lighting   has  
been

 
activated.
 Checking

 
by
 
means
 
of
 
the
 
indicator
 lamps

 
in
 
the
 
instrument
 
panel
 
is
 described

 
in
 
the
 
"Instruments
 
and
 controls"

 
section
 
of
 
chapter
 
3.
Direction indicators
Selection is by turning this
ring. Main
  beam   (blue)
To activate the lighting
control, turn this ring to
the lighting off position "0"
then to the selection of
your   choice.
o

n opening the driver's door, there is
an audible warning if you have left the
lighting
  on.
Steering mounted controls

60
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
If the sunshine sensor
does not function correctly,
the  lighting   comes   on  
accompanied

  by   the   service  
warning

  lamp,   an   audible  
signal

 
and   a   message   in   the   screen.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Guide-me-home lighting
Keeping the dipped beam headlamps on   temporarily   with   the   ignition   off,  
makes

  the   driver's   exit   easier   when   the  
light

  is   poor.
HEADLAMP BEAM
The beam setting must be adjusted to suit
  the   load   in   the   vehicle.
0 -
  No   load.
1 -
  Partial   load.
2 -
 
A
verage   load.
3 -
  Maximum   authorised   load.
Manual operation
-
 
With

 
the
 
ignition
 
off,
 
"flash"
 
the
 
headlamps

 
within
 
one
 
minute
 
after
 
switching

 
off
 
the
 
ignition.
The
 
guide-me-home
 
lighting
 
switches
 
of

f
 
automatically
 
after
 
a
 
set
 
time.
Automatic operation
Refer to chapter 10, "Screen
menu
 
map"
 
section. Initial setting is position 0.
a

ctivate the function via the
vehicle
 
configuration
 
menu. Programming
The
 
system
 
is
 
activated
 
or
 
deactivated
 
in

 
the
 
vehicle
 
configuration
 
menu.
The
 
system
 
is
 
activated
 
by
 
default.
Switching off
The
 
system
 
does
 
not
 
operate:
-

below a certain angle of rotation of
the steering wheel,
-

 
above

 
25
 
mph
 
(40
 
km/h),
-
 
when

 
reverse
 
gear
 
is
 
engaged.
Switching on
This
 
function
 
starts:
-

when the corresponding direction
indicator is switched on,
or
-

 
from

 
a
 
certain
 
angle
 
of
 
rotation
 
of
 
the

 
steering
 
wheel.
With
 
dipped
 
or
 
main
 
beam
 
headlamps,
 
this

 
function
 
makes
 
use
 
of
 
the
 
beam
 
from

 
a
 
front
 
foglamp
 
to
 
illuminate
 
the
 
inside of a bend, when the vehicle
speed

 
is
 
below
 
25
 
mph
 
(approximately
 
40

 
km/h)
 
(urban
 
driving,
 
winding
 
road,
 
intersections,

 
parking
 
manoeuvres...).
Cornering lighting
Travelling abroad
If using your vehicle in a country
that drives on the other side of the
road,
  the   headlamps   must   be   adjusted  
to

 
avoid   dazzling   on-coming   drivers.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
The
 
function
 
is
 
deactivated
 
temporarily
 
when

 
you
 
use
 
the
 
manual
 
lighting
 
control

 
stalk.
Steering mounted controls

 67
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
The speed of the vehicle responds to
the pressure of the driver's foot, up
to the the accelerator pedal's point of
resistance, which indicates that the
programmed  speed   has   been   reached.
However, pressing the pedal beyond
this
  point   of   resistance   to   the   floor  
allows

  the   programmed   speed   to   be  
exceeded.

 
T
o   resume   use   of   the   limiter,  
simply

  reduce   the   pressure   on   the  
accelerator pedal gradually and return
to

  a   speed   below   that   programmed.
Adjustments can be carried out
when stationary, with the engine
running, or with the vehicle moving. This
  speed   limiter   shows   the   function  
selection

  status   in   the   instrument   panel  
and

  displays   the   programmed   speed:SPEED LIMITER
"LIMIT"
Function selected,
displaying of the
"Speed
  Limiter"  
symbol.
Function of

f,
last
  programmed  
speed -

OFF.
Function
  on.
Vehicle speed above,
the
  programmed  
speed setting is
displayed

  flashing.
o

perating fault
detected,
OFF - the dashes
flash.
1.
 
Limiter

 
mode
 
On
 
/
 
Off.
2.
 
Reduce

 
programmed
 
speed
 
setting.
3.

 
Increase

 
programmed
 
speed
 
setting.
4.

 
Speed

 
limiter
 
On
 
/
 
Pause.
"This is the selected speed which the
driver
 
does
 
not
 
wish
 
to
 
exceed".
This
 
selection
 
is
 
made
 
with
 
the
 
engine
 running while stationary or with the vehicle


moving.
 
The

 
minimum
 
speed
 
which
 
can
 be

 
programmed
 
is
 
20
 
mph
 
(30
 
km/h).
Steering mounted controls
EaSE oF USE and CoMFoRT
4