2016 CADILLAC ELR lock

Cadillac ELR Owner Manual (GMNA-Localizing-U.S/Canada-9087644) -
2016 - crc - 9/17/15
Keys, Doors, and Windows 31
To remove the key, press the button
near the bottom of the transmitter,
and pull the key out. Never pull the
key out without pressing the button.
If it becomes difficult to turn the key,
inspect the key blade for debris.
See your dealer if a new key is
needed.
Contact Roadside Service if locked
out of the vehicle. SeeRoadside
Service 0336.
With an active OnStar subscription,
an OnStar Advisor may remotely
unlock the vehicle. See OnStar
Overview 0347.
Remote Keyless Entry
(RKE) System
See Radio Frequency
Statement 0343.
If there is a decrease in the RKE
operating range:
. Check the distance. The
transmitter may be too far from
the vehicle.
. Check the location. Other
vehicles or objects may be
blocking the signal.
. Check the transmitter's battery.
See “Battery Replacement” later
in this section.
. If the transmitter is still not
working correctly, see your
dealer or a qualified technician
for service.
Remote Keyless Entry
(RKE) System Operation
The Keyless Access system allows
for vehicle entry when the
transmitter is within range. See
“Keyless Access Operation”
following.
The RKE transmitter functions may
work up to 60 m (197 ft) away from
the vehicle.
Other conditions, such as those
previously stated, can impact the
performance of the transmitter.
ProCarManuals.com

Cadillac ELR Owner Manual (GMNA-Localizing-U.S/Canada-9087644) -
2016 - crc - 9/17/15
32 Keys, Doors, and Windows
K(Unlock) :Press once to unlock
the driver door. Press a second time
within five seconds to unlock all
doors.
The hazard warning lamps will flash
twice each time the button is
pressed and the alarm system will
be disarmed. See Vehicle Alarm
System 043.
Pressing and holding
Kwill open all
of the vehicle's windows. See Power
Windows 047. This feature can be
disabled by a dealer technician.
Q(Lock) : Press to lock all doors.
The hazard warning lamps will flash
once and the alarm system will be
armed. See Vehicle Alarm
System 043.
If the driver door is open when
Qis
pressed, all doors lock and then the
driver door will unlock if the
Unlocked Door Anti-Lockout feature
is enabled through vehicle
personalization. See Vehicle
Personalization 0145. This may
vary based on vehicle
personalization.
L(Vehicle Locator/Panic
Alarm) : Press and release to
initiate vehicle locator. The exterior
lamps flash and the horn chirps
three times. Press and hold for
three seconds to sound the panic
alarm. The horn sounds and the
turn signals flash for 30 seconds.
Press again to cancel the panic
alarm.
/(Remote Vehicle Start) : Press
and release
Qand then immediately
press and hold
/for at least
four seconds to start the vehicle
from outside using the RKE
transmitter. See Remote Start036.
i(Remote Trunk Release) :
Press and hold to release the trunk.
Keyless Access Operation
The vehicle has the Keyless Access
system that lets you unlock and
unlatch the doors and access the
trunk without removing the RKE
transmitter from your pocket, purse,
briefcase etc. The RKE transmitter
must be within 1m (3 ft) of the door
being opened. There is a touch pad
on the inside of the door handles. Keyless Access can be
programmed to unlock all doors on
the first touch pad press from the
driver door. See
Vehicle
Personalization 0145.
Keyless Unlocking from the
Driver Door
When the RKE transmitter is within
1 m (3 ft) of the driver door handle,
pressing the touch pad button on
the driver door handle will unlock
and open the driver door. See Door
Locks 038.
To customize whether the doors
automatically unlock all doors, see
Vehicle Personalization 0145.
Keyless Unlocking from the
Passenger Door
Press the door touch pad to unlock
all doors and open the passenger
door if the RKE transmitter is within
1 m (3 ft).
Passive Locking
This feature will lock the vehicle
several seconds after all doors are
closed if the vehicle is off and at
ProCarManuals.com

Cadillac ELR Owner Manual (GMNA-Localizing-U.S/Canada-9087644) -
2016 - crc - 9/17/15
Keys, Doors, and Windows 33
least one transmitter has been
removed or none remain in the
vehicle.
To customize whether the doors
automatically lock when exiting the
vehicle, seeVehicle
Personalization 0145.
If other electronic devices interfere
with the RKE transmitter signal, the
vehicle may not detect the RKE
transmitter inside the vehicle.
If passive locking is enabled, the
doors may lock with the RKE
transmitter inside the vehicle. Do
not leave the RKE transmitter in an
unattended vehicle.
Temporarily Disable Passive
Locking Feature
Temporarily disable the passive
locking by pressing and holding
K
on the interior door switch with a
door open for at least four seconds,
or until three chimes are heard.
Passive locking will then remain
disabled until
Qon the interior door
is pressed, or until the vehicle is
turned on. Keyless Trunk Opening
Press the touch pad to open if the
RKE transmitter is within 1 m (3 ft)
and the doors are locked. If the
doors are unlocked, the transmitter
is not required to open the trunk.
Keyed Access
To access a vehicle with a dead
transmitter battery, see
Door
Locks 038.
Programming Transmitters to
the Vehicle
Only RKE transmitters programmed
to this vehicle will work. If a
transmitter is lost or stolen, a
replacement can be purchased and
programmed through your dealer.
The vehicle can be reprogrammed
so that lost or stolen transmitters no
longer work. Each vehicle can have
up to eight transmitters programmed
to it.
Programming with a Recognized
Transmitter
A new transmitter can be
programmed to the vehicle when
there is one recognized transmitter. 1. The vehicle must be off and
both the recognized and new
transmitters must be with you.
2. Remove the key base from the recognized RKE transmitter.
3. Place the recognized transmitter in the cupholder.
4. Insert the vehicle key into thekey cylinder above the license
plate.
5. Open the trunk.
6. Turn the key counterclockwise five times within 10 seconds.
7. The DIC displays READY FOR REMOTE KEY 3 or 4, up to 8.
ProCarManuals.com

Cadillac ELR Owner Manual (GMNA-Localizing-U.S/Canada-9087644) -
2016 - crc - 9/17/15
34 Keys, Doors, and Windows
8. Remove the rubber liner toaccess the pocket. Place the
new transmitter, button side
down, on the indent in the
center console storage area.
9. Press POWER
O.
10. The DIC displays READY FOR REMOTE KEY 4 or 5, up to 8.
11. Press
QorKon each newly
programmed transmitter to
complete the process.
12. To program additional transmitters, repeat
Steps 8–11. Return the key base back into
the RKE transmitter.
13. Press and hold POWER
Ofor
at least 12 seconds to exit
programming.
Programming without a
Recognized Transmitter
If there are no currently recognized
transmitters available, follow this
procedure to program up to eight
transmitters. This feature is not
available in Canada. This procedure
will take approximately 30 minutes
to complete. The vehicle must be off
and all transmitters to be
programmed must be present.
1. Remove the key from the transmitter and insert the
vehicle key into the key
cylinder above the license
plate.
2. Open the trunk.
3. Turn the key counterclockwise five times within 10 seconds.
The DIC message displays
REMOTE LEARN PENDING
PLEASE WAIT.
4. Return the key base back into the RKE transmitter.
ProCarManuals.com

Cadillac ELR Owner Manual (GMNA-Localizing-U.S/Canada-9087644) -
2016 - crc - 9/17/15
Keys, Doors, and Windows 35
5. Wait for 10 minutes until theDIC displays PRESS ENGINE
START BUTTON TO LEARN,
then press POWER
O.
The DIC reads REMOTE
LEARN PENDING,
PLEASE WAIT.
6. Repeat Step 5 two additional times. After the third time all
previously known transmitters
will no longer work with the
vehicle. Remaining transmitters
can be relearned during the
next steps. The DIC display
should now show READY FOR
REMOTE #1.
7. Remove the rubber liner toaccess the pocket. Place the
new transmitter, button side
down, on the indent in the
center console storage area.
8. Press POWER
O. When the
transmitter is learned, the DIC
display will show that it is ready
to program the new transmitter.
9. Remove the transmitter from the transmitter pocket and
press
QorKon the
transmitter.
10. To program additional transmitters, repeat Steps 7–9.
11. When all additional transmitters are programmed, press and
hold POWER
Ofor
approximately 12 seconds to
exit programming mode.
Starting the Vehicle with a Low
Transmitter Battery
When you try to start the vehicle,
if the transmitter battery is weak,
or if there is interference with the
signal, the DIC may display NO
REMOTE DETECTED or NO REMOTE KEY WAS DETECTED
PLACE KEY IN TRANSMITTER
POCKET THEN START YOUR
VEHICLE. See
Key and Lock
Messages 0139.
To start the vehicle:
1. Open the center console storage area and the
storage tray.
2. Place the transmitter, buttonside down, into the transmitter
indent.
3. With the vehicle in P (Park) or N (Neutral), press the brake
pedal and POWER
O.
ProCarManuals.com

Cadillac ELR Owner Manual (GMNA-Localizing-U.S/Canada-9087644) -
2016 - crc - 9/17/15
Keys, Doors, and Windows 37
.If the heated seats have been
enabled through vehicle
personalization, the heated
seats will turn on during colder
outside temperatures. See
“Remote Start Auto Heated
Seats” underHeated Front
Seats 056 and “Remote Start
Auto Heat Seats” underVehicle
Personalization 0145.
. The rear defogger will turn on
during colder outside
temperatures.
. The engine may turn on during
colder outside temperatures.
. Selecting
1during colder
outside temperatures before
shutting the vehicle off will help
windshield clearing.
. Shutting the vehicle off in ECO
Mode without
1selected will
minimize the impact to electric
range. Shutting the vehicle off in
other modes will maximize
heating or air conditioning.
. Use remote start to heat or cool
the interior when the vehicle is
plugged in to maximize the electric range by utilizing
electricity from the electrical
outlet. See
“Engine Assisted
Heating Plugged-In” under
Vehicle Personalization 0145.
. Vehicle range may decrease if
the vehicle is not plugged into
an electrical outlet. If the vehicle
is plugged in, much of the
energy needed to support this
feature will be provided from the
electrical outlet, not from the
high voltage battery.
Laws in some communities may
restrict the use of features that
remotely start the engine. For
example, some laws may require a
person using the remote start
feature to have the vehicle in view
when doing so. Check local
regulations for any requirements on
remote starting of vehicles.
The RKE transmitter range may be
shorter while the vehicle is running.
Other conditions can affect the
performance of the transmitter. See
Remote Keyless Entry (RKE)
System 031.
Starting the Vehicle
To heat or cool the passenger
compartment using remote start:
1. Press and release
Qon the
RKE transmitter; the doors
will lock.
2. Immediately press and hold
/
until the turn signal lamps
flash, or for at least
four seconds. Pressing
/
again during a remote start will
turn the feature off.
Remote start will automatically shut
off after 10 minutes unless a time
extension is done.
While the remote start is active, the
parking lamps will turn on and
remain on.
After entering the vehicle during a
remote start, press the POWER
O
button on the center stack with the
brake pedal applied to operate as
normal.
ProCarManuals.com

Cadillac ELR Owner Manual (GMNA-Localizing-U.S/Canada-9087644) -
2016 - crc - 9/17/15
38 Keys, Doors, and Windows
The remote start can be initiated
two separate times between driving.
For each remote start, the
passenger compartment will be
heated or cooled for 10 minutes.
Extending Vehicle Run Time
The vehicle run time can also be
extended by another 10 minutes,
if during the first 10 minutes
Steps 1 and 2 are repeated while
the engine is still running. An
extension can be requested,
30 seconds after starting. This
provides a total of 20 minutes.
The remote start can only be
extended once.
When the remote start is extended,
the second 10-minute period is
added on to the first 10 minutes for
a total of 20 minutes.
A maximum of two remote starts,
or a remote start with an extension,
are allowed between ignition cycles.
The vehicle's ignition must be
changed to ON/RUN and then back
to OFF before the remote start
procedure can be used again.
Canceling Remote Start
To cancel a remote start, do any of
the following:
.Press and hold
/until the
parking lamps turn off.
. Turn on the hazard warning
flashers.
. Press the POWER
Obutton on
the center stack, with the brake
pedal applied, then press
POWER
Oagain to turn the
vehicle off.
Conditions in Which Remote
Start May Not Work
Conditions in which a remote start
may not occur include:
. An open hood.
. The RKE transmitter is in the
vehicle.
. Vehicle propulsion system fault
conditions, including an
emission control system
malfunction.
. High voltage battery fault
conditions. A remote start or extension will not
occur if the fuel level is low.
During a remote start, conditions in
which a remote start may be
canceled include:
.
Vehicle propulsion system or
high voltage battery fault
conditions.
. Low engine oil pressure.
. Engine coolant temperature that
is too high.
Door Locks
{Warning
Unlocked doors can be
dangerous.
. Passengers, especially
children, can easily open
the doors and fall out of a
moving vehicle. The chance
of being thrown out of the
vehicle in a crash is
increased if the doors are
not locked. So, all
(Continued)
ProCarManuals.com

Cadillac ELR Owner Manual (GMNA-Localizing-U.S/Canada-9087644) -
2016 - crc - 9/17/15
Keys, Doors, and Windows 39
Warning (Continued)
passengers should wear
safety belts properly and the
doors should be locked
whenever the vehicle is
driven.
. Young children who get into
unlocked vehicles may be
unable to get out. A child
can be overcome by
extreme heat and can suffer
permanent injuries or even
death from heat stroke.
Always lock the vehicle
whenever leaving it.
. Outsiders can easily enter
through an unlocked door
when slowing or stopping
the vehicle. Lock the doors
to help prevent this from
happening.
To lock or unlock the doors from the
outside press
QorKon the RKE
transmitter.
For Keyless Access, the RKE
transmitter must be within 1 m (3 ft)
of the door handle sensor (1). Grip
and press to open.
To lock or unlock the doors from the
inside, press
QorKon the power
door lock switch (2).
To open the door, press the door
latch button (3). If the vehicle is
stationary, the door latch button
unlatches an unlocked door.
See “Keyless Access Operation” in
Remote Keyless Entry (RKE)
System Operation 031.
Power Door Locks
Q: Press to lock the doors. The
indicator light in the switch will
illuminate when activated.
K: Press to unlock the doors.
Loss of Vehicle Electrical
Power
If the vehicle has lost battery power,
open the doors manually.
ProCarManuals.com