2016 BUICK ENVISION ignition

4
Remote Keyless Entry Transmitter
Keyless Access System
F Optional equipment
Unlock
Press to unlock the
driver’s door. Press
again to unlock all
doors.
Power Liftgate
Press twice to open or
close the liftgate. Press
once to stop power liftgate operation.
Lock
Press to lock all doors.
Vehicle Locator/Panic Alarm
Press and release to locate your vehicle.
The exterior lamps will flash and the horn
will sound.
Press and hold to activate the alarm. Press
it again to cancel the alarm.
Note: To change the remote lock, unlock, and
remote start settings, go to Remote Lock, Unlock,
Start in the Vehicle Settings menu.
Remote Vehicle Start
Press and release the
Lock button and
then immediately press and hold the

button until the turn signal lamps flash to
start the engine from outside the vehicle.
After entering the vehicle, turn on the
ignition.
• During a remote start, the engine will
run for 10 minutes. Repeat these steps
to run the engine for an additional 10
minutes. A remote start can be extend
-ed once.
• Press and hold the
button until
the parking lamps turn off to cancel a
remote start.
Remote Start and Heated Seats: Select
the remote start heated seat option in the
Vehicle Settings to have the heated seats
turn on during a remote start. The heated
seat button indicators do not illuminate
and the temperature of the unoccupied
seat may be reduced during a remote start.
See Keys, Doors and Windows in your Owner Manual.
The Keyless Access System enables operation of the doors, igni-tion and liftgate without removing the Remote Keyless Entry
transmitter from your pocket or purse. The transmitter must be within 3 feet of the door being unlocked or the liftgate.
Keyless Unlocking
With the transmitter within range:
Press the lock button on the driver’s door handle to unlock
the driver’s door; press it again within 5 seconds to unlock all doors.
Press the lock button on a passenger door handle to unlock all doors.
Press the touchpad on the liftgate handle to open the liftgate.
Keyless Locking
With the ignition off, the transmitter removed from the vehicle, and all doors closed:
Press the lock button on any door handle to lock all doors immediately.
If Passive Locking is turned on, all doors will lock automatically after a short delay.
Note: To change the Keyless Locking and Unlocking settings, go to Remote Lock, Unlock, Start in the
Vehicle Settings menu.
See Keys, Doors and Windows in your Owner Manual.

5
Pushbutton Start
Auto Engine Stop/Start
Start
With the vehicle in Park or Neutral, press
the brake pedal and then press the
ENGINE START/STOP button to start the
engine. The green indicator on the button
will illuminate.
Note: The transmitter must be in the vehicle to turn
on the ignition. If the transmitter battery is weak,
place the transmitter in the front cupholder to
enable the engine to start. Replace the transmitter
battery as soon as possible.
Stop/Off
Shift to Park and press the ENGINE START/STOP button to turn off the engine.
Power will be available for 10 minutes to operate the audio system until the driver’s door
is opened and to operate the windows and sunroof
F until any door is opened.
Accessory Mode
With the engine off and the brake pedal NOT depressed, press the ENGINE START/
STOP button to place the ignition system in the accessory mode. The amber indicator
on the button will illuminate.
See Driving and Operating in your Owner Manual.
A fuel-saving stop/start system has been integrated with the 2.0L engine. While driv-ing, when the brake pedal is applied and the vehicle is at a complete stop, the automatic
engine stop/start system may turn off the engine, depending on operating conditions.
When the engine is off, the tachometer gauge will read AUTO STOP. Upon releasing the
brake pedal or applying the accelerator pedal, the engine will restart. After parking the
vehicle and turning off the engine, the tachometer gauge will read OFF.
The engine may remain running or restart if:
• A minimum vehicle speed is not reached.
• The engine or transmission is not at the required operating temperature.
• The outside temperature is not in the required operating range.
• The shift lever is in any gear other than Drive (D).
• The battery charge is low.
• The current settings for the climate control or defog system have not been reached.
• The Auto Stop time is greater than 2 minutes.
See Driving and Operating in your Owner Manual.

6
Front Seats
Set Memory Seat Positions
With the ignition On or in Accessory mode:
1. Adjust the seat and power outside
mirrors to the desired positions.
2. Press and release the SET button on the
driver’s door. A beep will sound.
3. Immediately press and hold button 1
until two beeps sound.
Repeat these steps using button 2 for a
second driver.
To store a seat position for more clearance when exiting the vehicle, repeat these steps
using the
Exit button instead of button
1 or 2.
Recall Memory Seat Positions
Press and hold button 1, 2 or Exit until the seat and mirrors reach the set position.
The memory/exit positions can be programmed to be recalled automatically.
To set the Auto Memory Recall or Easy Exit options, go to the Settings > Vehicle >
Comfort and Convenience menu.
See Seats and Restraints in your Owner Manual.
Power Seat Adjustments
A. Seat Adjustment
Move the horizontal control to move
the seat forward or rearward and to tilt,
raise or lower the seat.
B. Seatback Recline Adjustment
Move the vertical control to recline or
raise the seatback.
C. Lumbar Support Adjustment
Press the rear control to adjust the
amount of lumbar support.
Steering Wheel Adjustment
With the vehicle parked, push down the lever under the steering column to adjust the
steering wheel. The steering wheel can then be moved up or down and in or out. Pull
up the lever to lock the steering wheel in place.
See Instruments and Controls in your Owner Manual.
Ac
B

16F Optional equipment
Cruise Control
Traction Control and StabiliTrak Systems
Setting Cruise Control
1. Press the
On/Off button. The Cruise Control symbol will illuminate in white on
the instrument cluster.
2. When traveling at the desired speed, press the SET– button to set the speed. The

symbol will illuminate in green on the instrument cluster.
Adjusting Cruise Control
RES+ Resume/Accelerate
Press up to resume a set speed. When the
system is active, press up to increase speed.
SET– Set/Coast
When the system is active, press down to
decrease speed.
Following Gap (Adaptive Cruise ControlF)
Press to select a following gap setting of Far, Medium, or Near.
Cancel
Press to cancel the cruise control without erasing the set speed from memory. Pressing
the brake pedal will also cancel the cruise control.
The cruise control set speed is erased when cruise control or the vehicle ignition is
turned off.
Adaptive Cruise Control
F
The system maintains the cruise control set speed and a following gap — the time
between your vehicle and a vehicle detected directly ahead — by accelerating or braking.
Following Gap
Press to select a following gap setting of Far, Medium, or Near. This is also the Forward
Collision Alert setting.
See Driving and Operating in your Owner Manual.
The traction control system limits wheelspin and the StabiliTrak® stability control system
assists with directional control of the vehicle in difficult driving conditions. Both systems
turn on automatically every time the vehicle is started. Turn off traction control if the
vehicle is stuck and rocking the vehicle is required.
Press the Traction Control/StabiliTrak Off button at the front of the center console
to turn traction control on or off.
See Driving and Operating in your Owner Manual.

17
Automatic Transmission
Electric Parking Brake
Driver Shift Control
Driver Shift Control is a manual mode that
allows the driver to shift gears manually.
This feature can be used to limit the top
gear and vehicle speed or to downshift
when driving on a downhill grade to provide
engine braking.
1. Move the shift lever left to the L (Low)
position.
2. Press the + (plus) or – (minus) button on
the shift lever to upshift or downshift.
The current gear will be displayed on the Driver Information Center.
If vehicle speed is too high or too low for the requested gear, the shift will not occur.
See Driving and Operating in your Owner Manual.
To apply the parking brake, pull the
Parking Brake switch.
To release the parking brake, turn on the
ignition, press the brake pedal, and then
press the
switch.
Note: The parking brake will release automatically
if the vehicle is running, placed into gear and an
attempt is made to drive.
See Driving and Operating in your Owner Manual.
Tire Pressure Monitor
The Low Tire Pressure warning light on the instrument cluster illuminates when one
or more of the vehicle’s tires is significantly underinflated. Fill the tires to the proper tire
pressures listed on the Tire and Loading Information label located below the driver’s door
latch. Current tire pressures can be viewed in the Driver Information Center.
See Vehicle Care in your Owner Manual.