2016 AUDI TT COUPE height

Downloaded from www.Manualslib.com manuals search engine Wheels
be happy to provide more infor­
mation.
® Mud and snow capability
"M/S" or "M+S" indicates the tire
has characteristics that make it
suitable for driving on mud and
snow. & indicates a winter t ire.
@ Compos ition of the tire cord
and materials
The number of plies indicates the
number of rubberized fabric lay­
ers in the tire. In general: the
more layers, the more weight a
tire can carry. Tire manufacturers
must also specify the materials
used in the tire. These include
steel, nylon, polyester and other
materials.
@Maximum permitted load
This number indicates the maxi­
mum load in kilograms and
pounds that the tire can carry.
@Uniform tire quality grade
standards for treadwear,
traction and temperature
resistance
Tread wear, t raction and temper­
ature ranges c:> page 266.
252
@ Running direction
~ Maximum permitted
inflation pressure
This number indicates the maxi­
mum pressure to which a tire can
be inflated under normal operat­
ing conditions.
Glossary of tire and loading
terminology
Accessory weight
means the combined weight (in
excess of those standard items
wh ich may be replaced) of auto­
matic transmission, power steer­
ing , power brakes, power win­
dows, power seats, radio , and
heater, to the extent that these
items are available as factory-in­
stalled equipment (whether in­
stalled or no t).
Aspect ratio
means the ratio of the height to
the width of the tire in percent.
Numbers of SS o r lower indicate a
low
sidewall for improved steer­
ing response and better overa ll
handling on dry pavement.
Bead
means the part of the tire that is
made of steel wires, wrapped or ...

Downloaded from www.Manualslib.com manuals search engine ~Only use winter tires that are approved for your
vehicle.
~Please note that the maximum permitted
speed may be lower with winter tires q ,&.. An
authorized Audi dealer or authorized Audi Serv­
ice Facility
can inform you about the maximum
permitted speed for your tires.
~Check the tire pressure after installing wheels
qpage260.
The effectiveness of winter tires is reduced great­
ly when
the tread is worn down to a depth of
0.157 in (4 mm). The characteristics of winter
tires also decrease greatly as the tire ages, re­
gardless
of the remaining tread.
A WARNING
1-=---Never drive faster than the maximum per-
mitted speed for your tires. This could cause
the tires to heat up too much. This increases
the risk
of an accident because it can cause
the
tire to burst.
- Always
adapt your driving to the road and
traffic conditions. Drive carefully and reduce
your speed on icy or slippery roads.
Even
winter tires can lose traction on black ice.
@ For the sake of the environment
Reinstall summer tires at the appropriate
time, because they provide better handling
when roads are free
of snow and ice. Summer
tires cause
Less road noise, tire wear and fuel
consumption.
(j) Tips
You can also use all season tires instead of
winter tires. Please note that in some coun­
tries where
winter tires are required, only
winter tires with the & symbol may be per­
mitted.
Snow chains
Snow chains not only improve the driving in win­
ter road conditions, but also the braking.
~Only install snow chains on the front wheels.
This applies also
to vehicles with all wheel
drive*.
Wheels
~Check and correct the seating of the snow
chains
after driving a few feet, if necessary. Fol­
low
the instructions from the manufacturer.
~Note the maximum speed of 30 mph (50 km/
h). Note the Local regulations.
Use of snow chains is only permitted with certain
rim/tire combinations due to technical reasons.
Check with an authori zed Audi dealer or author­
ized Audi Service Facility
to see if you may use
snow chains .
You must remove the snow chains on roads with­
out snow . Otherwise, you could impair driving
ability and damage the tires.
A WARNING
Using incorrect snow chains or installing snow
chains incorrectly
can result in loss of vehicle
control, which increases
the risk of an acci­
dent.
CD Note
- Snow chains can damage the rims/wheel
covers* if the chains come into direct con·
tact with them. Remove the wheel covers*
first. Use coated snow chains.
-
Using snow chains that add more than 0.53
in (0.53 in) of height can severely damage
the wheel housings and
other vehicle com­
ponents.
(D Tips
When using snow chains, it may be useful to
switch on sport mode ~page 88.
Low aspect ratio tires
Your Audi is factory-equipped with low aspect ra­
tio tires. These tires have been thoroughly tested
and been selected specifically
for your model for
their superb performance, road feel and handling
under a variety
of driving conditions. Ask your au­
thorized Audi dealer
for more details .
The
Low aspect ratio of these tires is indicated by
a numeral
of SS or less in the tire's size designa­
tion. The numeral represents the ratio of the
tire's sidewall height in relation to its tread width..,.
265

Downloaded from www.Manualslib.com manuals search engine Emergency assistance
car to keep your balance and take care not
to slip.
Raising the vehicle
The vehicle must be li~ed w ith the jock first be­
fore the wheel can be removed.
-fi·--
Fig. 203 Sill panels: markings
Fig.
204 Sill : po sitioning th e ve hicl e jack
... Engage the parking brake to prevent your vehi­
cle from rolling unintentionally.
... Move the selector lever to position P.
... Find the marking (imprint) on the sill that is
nearest the wheel that will be changed. Behind
the marking, there is a lifting point on the sill
for
the vehicle jack.
... Vehicles with a sill: note the position of the sill
when positioning
the vehicle jack o fig. 204.
... Place the vehicle jack (vehicle tool kit) on a firm
surface.
Use a flat, stable support if necessary.
On a slippery surface such as tile, you should
use a non-slip pad (such as a rubber mat) o _&.
... Turn the vehicle jack located under the lifting
point on the sill to raise the jack until its arm@
c:> fig. 204 is located under the designated plas­
tic
mount c:> _&, c:>Q).
... Align the jack so that its arm@o fig. 204 en­
gages in the designated lifting point in the door
sill and the movable base@ lies flat on the
280
ground. The base@ must be vertical under the
lifting point@ .
... Wind the jack up further until the flat tire
comes off the ground c:> _&.
Position the vehicle jack only under the designat­
ed lifting points on the sill c:> fig. 203. There is ex­
actly
one location for each wheel. The jack must
not be positioned at any other location c:> .&,c:>Q).
An unstable surface under the jack can cause the
vehicle to slip off the jack. Always provide a firm
base for the jack on the ground. If necessary
place a
sturdy board or similar support under the
jack. On hard, slippery surfaces (such as tiles)
u
se a rubber mat or similar to prevent the jack
from slipping c:> .&..
A WARNING
- I
-You or your passengers could be injured
while changing a
wheel if you do not follow
these safety precautions:
- Position
the vehicle jack only at the desig­
nated lifting points and align the jack.
Otherwise,
the vehicle jack could slip and
cause an injury if it does not have suffi­
cient hold on the vehicle.
- A
soft or unstable surface under the jack
may cause the vehicle to slip off the jack .
Always provide a firm
base for the jack on
the ground. If necessary, use a sturdy
board under the jack .
-
On hard, slippery surface (such as tiles)
use a
rubber mat or similar to prevent the
jack
from s lipp ing.
-
Only rais e your vehicle with the vehicle
jack provided by
the factory. If you use a
vehicle jack for
another vehicle, your vehi­
cle can slide
and cause injury .
- Changes
in temperature or load can affect
the height of the vehicle.
- Never
start the engine when the vehicle is
raised, which could
cause an accident .
-
Support the vehicle securely with appro­
priate stands if work is to be performed
underneath the vehicle; otherwise, there
is a potential risk of injury.

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
.....
"' .....
-To help prevent injury to yourself and your
passengers:
-Do not raise the vehicle until you are sure
the jack is securely engaged.
-Passengers must not remain in the vehicle
when it is jacked up.
- Make
sure that passengers wait in a safe
place away from the vehicle and well away
from
the road and traffic.
- Make
sure jack position is correct, adjust
as necessary and then continue to raise
the jack.
- Changes
in temperature or load can affect
the height of the vehicle.
CD Note
Do not lift the vehicle by the sill. Position the
vehicle jack only at the designated lifting
points on the sill. Otherwise, your vehicle will
be damaged.
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang­
ing the wheel.
Fig. 205 Chang ing a wheel: using the screwdr ive r handle
(with
the b lade remo ved) to turn the bolts
Fig. 206 Changing a wheel: alignme nt pin inside the top
hole
Emergency assistance
After you have loosened all wheel bolts and
raised
the vehicle off the ground, remove and re­
place
the wheel as follows:
Removing the wheel
.... Use the hexagonal socket in the screwdriver
handle
to completely remove the topmost
wheel bolt and set it aside on a clean surface
¢fig. 205.
.... Screw the threaded end of the alignment pin
from the tool kit hand-tight into the empty bolt
hole ¢fig. 206.
.,. Then remove the other wheel bolts as described
above .
.,. Take off the wheel leaving the alignment pin in
the bolt hole ~CD.
Putting on the compact spare wheel
... Lift the spare wheel and carefully slide it over
the alignment pin to guide it in place ¢(0.
... Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel bolts
slightly .
.,. Remove the alignment pin and insert and tight­
en the remaining wheel bolt slightly like the
rest .
.... Turn the jack handle counter-clockwise to lower
the vehicle until the jack is fully released .
.... Use the wheel bolt wrench to tighten all wheel
bolts firmly ¢ page 2 79. Tighten them cross­
wise,
from one bolt to the (approximately) op­
posite one, to keep the wheel centered.
CD Note
When removing or installing the wheel, the
rim could hit the brake rotor and damage the
rotor. Work carefully and have a second per­
son help you.
@ Tips
Never use the hexagonal socket in the handle
of the screwdriver to loosen or tighten the
wheel bolts.
-Pull the reversible blade from the screwdriv­
er before you use the hexagonal socket in
the handle to turn the wheel bolts.
281

Downloaded from www.Manualslib.com manuals search engine Vehicle capacity weight
The vehicle capacity weight (max. load) is listed
either on the driver's side B-pillar or inside the
fuel filler flap.
& WARNING
- The
actual Gross Axle Weight Rating at the
front and rear axles should not exceed the
permissible weights, and their combination
must not exceed the Gross Vehicle Weight
Rating .
- Exceeding
permissible weight ratings can
result in vehicle damage, accidents and per­
sonal injury .
Dimensions
The dimensions can vary depending on the model
and equipment.
Length
Width
Width
across the mirrors
Height at curb weight
When driving on poor roads, by curbs and on
steep ramps, make sure that low-lying compo­
nents such as the spoiler and exhaust system do
Capacities
Fuel tank
Windshield and headlight washer system*
Technical data
@ Note
- The vehicle capacity
weight figures apply
when the load is distributed evenly in the
vehicle (passengers and luggage). When
transporting a heavy load in the luggage
compartment, carry the load as near to the
rear axle as possible so that the vehicle's
handling is not impaired.
-Do not exceed the maximum permissible
axle loads or the maximum gross vehicle
weight. Always remember that the vehicle's
handling will be affected by the extra load.
Therefore, adjust your speed accordingly.
- Always
observe local regulations.
in (mm) 164.7 (4,184)
in (mm) 72.l (1832)
in (mm) 77.4 (1966)
in (mm) 53.3 (1353)
not come into contact with these or they could be
damaged. This applies especially when the vehi­
cle is fully loaded.
gal (l) approx. 14.5 (55)
gal (l) approx. 2.4 (9.0)
299