2016 AUDI S7 change wheel

M N <( I.J "". rl I.O
"' N I.O rl
_& WARNING
Temperature grades apply to tires that are properly inflated and not over or underinflat­
ed .
Tire pressure monitoring
system
CD General notes
Each tire, includ ing the spare (if provided),
should be checked monthly when cold and inflat­
ed to the inflation pressure recommended by the
vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your veh icle has
tires of a different size than the size indicated on
the vehicle placard or tire inflation pressure la­
be l, you shou ld determine the proper tire infla­
tion pressure for those tires).
As an added safety feature, your vehicle has been
equipped with a tire pressure monitoring system
(TPMS) that illuminates a low tire pressure tell­
tale when one or more of your tires is significant­ ly under -inflated. Accordingly, when the low tire
pressure telltale illuminates, you should stop and
check your tires as soon as poss ible, and inflate
them to the proper pressure. Driving on a signifi­ cantly under-inflated tire causes the tire to over­
heat and can lead to t ire failure. Under-inflation
also reduces fuel efficiency and tire tread life,
and may affect the vehicle's handling and stop­
ping ability .
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsib ility to ma inta in correct tire pressure,
even if under-inflation has not reached the level
to trigger illuminat ion of the TPMS low t ire pres­
sure telltale.
Your vehicle has also been equ ipped with a TPMS
malfunction indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire
pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi­
mately one minute and then remain continuously
illuminated . This sequence will cont inue upon
Wheels
subsequent vehicle start -ups as long as the mal­
function exists.
When the malfunction indicator is illuminated ,
the system may not be able to detect or signal
low tire pressure as intended . TPMS malfunctions
may occur for a variety of reasons, including the
i nsta llation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly. Always check the
TPMS malfunction telltale after replacing one or
more t ires or wheels on your veh icle to ensure
that the replacement or alternate t ires and
whee ls allow the TPMS to continue to function
properly.
If the Tire Pressure Monitoring System
indicator appears
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system mo/function .
Fig. 199 Instrument cluster: indicator light with message
Using the ABS sensors, the tire pressure monitor­
ing system compares the tire tread circumference
and vibration characteristics of the individual
tires . If the pressure changes in one or more
t ir es, this is indicated in the instrument cluster
display with an indicator light
HE and a message.
If only one tire is affected, the location of that
tire will be indicated.
T he tire pressures must be stored in the Infotain­
ment system again each time the pressures
change (switching between partial and full load
pressure) or after changing or rep lacing a tire on
your vehicle
¢ page 252. The ti re pressure moni­
toring system only monitors the tire pressure you have stored. Refer to the tire pressure label for ..,.
251

Wheels
the recommended tire pressure for your vehicle
¢ page 243, fig. 198.
Tire tread ci rcumfe rence and v ibration character­
istics can change and cause a tire pressure warn­
ing if:
- the tire pressure in one or more t ires is too low .
- the tire has structural damage .
- the tire was replaced or the tire pressure was
changed and it was not stored
¢ page 252.
-the spare tire* is installed .
Indicator lights
IE Loss of pressure in at least one tire¢.&. .
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
¢page 252 .
mm (Tire Pressure Monitoring System) Tire pres­
sure: System malfunction!. Ifffim
appears after
switching the ignition on or while driving and the
IE indicator light in the instrument cluster
blinks for approximately one minute and then
stays on, there is system malfunction . Try to
store the correct tire pressures¢ page 252. If
the indicator light does turn off or turns on again
after a short period of time, drive to your author­
ized Audi dealer or authorized Audi Service Facili­
ty immediately to have the malfunction correct­
ed .
A WARNING
- If the tire pressure indicator appears in the
display, reduce your speed immediately and
avoid any hard steering or braking maneu­
vers . Stop as soon as possible and check the
t ir es and their pressure .
- The driver is responsible for maintaining the correct tire pressure. You must check the
tire pressure regularly.
- Under certain conditions (such as a sporty
dr iving style, winter cond itions or unpaved
roads), the tire pressure monitoring system
indicator may be delayed.
- Do not use run-flat tires on your veh icle. Us­
ing them when not permitted can lead to
vehicle damage or accidents.
252
(D Tips
-The tire pressure monitoring system can al­
so stop working when there is an ESC mal­
function.
- Using snow chains may result in a system
malfunction.
- The tires with the identification "AO" or
"RO" ¢
page 240 have been matched with
your Audi tire pressure monitoring system.
We recommend that you use these tires.
Storing tire pressures
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys­ tem.
... Make sure before storing that the tire pressures
of all four tires meet the specified values and
are adapted to the load¢
page 243 .
... Switch the ignition on .
... Select: the
I CARI function button > (Car)* Sys­
tems
control button > Servicing & checks > Tire
pressure monitoring
> Store tire pressures >
Yes, store now.
(D Tips
Do not store the tire pressures if snow chains
are instal led.

M N <( (.J
'SI: ,...., \!) 1.1'1
N \!) ,....,
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel .
.,. After you experience a tire failure, pull the car
well away from moving traffic and try to reach
level ground before you stop¢,& .
.. All passengers should
leave the car and move
to a safe location (for instance, beh ind the
guardrail) ¢ ,& .
.,. Engage the
parking brake to prevent your vehi­
cle from rolling unintentiona lly ¢,& .
.. Move
selector lever to position P ¢ ,& .
1> lfyou are towing a trai ler, unhitch the trailer
from your vehicle .
.,. Take the
jack and the spare tire out of the lug­
gage compartment
¢ page 253, ¢ page 254.
.,&. WARNING
You or your passengers could be injured while
changing a wheel if you do not follow these
safety precautions:
- If you have a flat tir e, move a safe distance
off the road. T urn off the engine, turn the
emergency flashers on and use other warn­
ing devices to alert other mo torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
- T o help prevent the vehicle from moving
sudden ly and possibly slipping off the jack,
always fully set the parking brake and block
the wheel diagonally opposite the wheel be­ ing changed. When one front wheel is lifted
off the ground, placing the Automatic Trans­
mission in P (Park) will
not prevent the vehi­
cle from moving.
- Before you change a wheel, be sure the
ground is level and firm . If necessary, use a
stu rdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced tir e in the luggage com­
partment ¢
page 132.
Emergency assistance
{!) Tips
Before changing the whee l, you must activate
the jacking mode, so that the automat ic con­
trols for the Adapt ive Air Suspension* do not
make it more difficult to lift the vehicle with
the jack ¢
page 257 .
Changing a wheel
When you change a wheel , follow the sequence
described below step-by-s tep and in exactly tha t
order .
l. Activate the vehicle jack mode* ¢ page 2 5 7.
2. Remove the
decorative wheel cover*. For
more details see also¢
page 256, Decora ­
tive wheel covers
or¢ page 256, Wheels
with wheel bolt caps .
3. Loosen the wheel bolts ¢page 256.
4. Locate the pro per mounting point for the
jack and align the jack be low that point
¢page 257.
5. Raise the car with the jack¢ page 257 .
6. Remove the wheel with the flat tire and then
install
the spare ¢ page 259.
7. Tighten all wheel bolts ligh tly.
8.
Lower the vehicle with the jack .
9. Use the wheel bolt w rench and
firmly tighten
all wheel bolts¢
page 256 .
10. Replace the decorative wheel cover*.
11. Deactivate the vehicle jack mode* in the
MMI :
ICAR I funct ion button > (C ar)* systems
control button > Servicing & checks > Air
susp.: jack mode > Off .
The vehicle jack mode* switches off automatically
at speeds above 6 mph (10 km/h) .
.,&. WARNING ~ -
Always read and follow all WARNINGS and in ­
formation ¢
.& in Raising the vehicle on
page 258
and ¢ page 260.
255

Emergency assistance
After changing a wheel
A wheel change is not complete without the do­
ing the following .
• Always store the vehicle tool kit, the jack* and
the replaced tire in the luggage compartment
¢page 132.
• Check the tire pressure on the spare wheel im­
med iately after mounting it.
• As soon as possible, have the
tightening tor­
ques
on all wheel bolts checked with a torq ue
wrench . The correct tightening torque is 90 ft
lb (120 Nm).
• Have the flat tire
replaced as soon as possible.
@ Tips
-If you notice that the wheel bolts are cor­
roded and difficult to turn while changing a
tire, they should be replaced before you
check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked .
- After changing a wheel, the tire pressure in
all four tires must be checked/corrected and
the tire pressure mon itor ing indicator must
be stored in the MMI
¢ page 252.
Decorative wheel covers
App lies to veh icles: w ith decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 203 Changing a wheel : Removing the wheel cover
Removing
• Insert the hook (provided with the vehicle tool
kit) in the hole in the wheel hub cover.
• Pull off the
decorative wheel cover¢ fig. 203.
256
Wheels with wheel bolt caps
Applies to vehicles: wi th whee l bo lts with caps
The caps must be removed first from the wheel
bolts before the bolts can be unscrewed .
Fig. 204 Changing a wheel: removing th e wheel bolt caps
Removing
• Push the plastic clip (provided with the vehicle
tool kit) over the whee l bolt cap until the inner
retainers on the clip align with the edge of the
cover .
• Remove the cap with the
plastic clip (vehicle
tool k it)
~ fig . 204 .
Refitting
• Place the caps over the wheel bolts and push
them back on.
The caps are to protect and keep the wheel bolts
clean.
Loosening and tightening the wheel bolts
The wheel bolts must be loosened before raising
the vehicle.
Fig. 205 Changing a wheel: loosen ing the whee l bo lts

M N <( I.J "". rl I.O
"' N I.O rl
Loosening
• Slide the wh eel wr ench onto the wheel bolt as
far as it will go.
• Take tight hold of the
end of the wrench handle
and turn th e wheel bolts
counte r-cl oc kwi se
a bout one single turn in the direction of arrow
¢ fig . 205.
T ightening
• Slide th e wheel wrench onto the whee l bolt as
far as it w ill go .
• Take tight hold of the
end of the wrench handle
and turn each whee l bolt
cloc kwise until it i s
s eated .
A WARNING
- Do not use force or hurry when chang ing a
wheel· you can cause the vehicle to slip off
the jack and cause serious personal injur ies.
- Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. - You risk an injury .
(D Tips
-Never use the hexagonal socket in the han ­
dle of the screwdriver to loosen or tighten
the wheel bo lts.
- If a wheel bolt is
very tight, you may find it
easier to loosen by carefully pushing down
on the end of the whe el bo lt wrench w ith
one foot only . As you do so, hold on to the
car to keep your ba lance and take care not
to slip .
Emerg en cy ass is tan ce
Raising the vehicle
The vehicle must be lifted with the jock first be­
fore the wheel con be removed.
Fig . 206 Sill pan els: ma rking s
O') ...
0
---~~ i~~:--~
F ig . 207 Sill: p osit ioning th e ve hicl e ja ck
• Activate the v eh icle jack mode* in the MMI:
!CARI function button > ( Car) * sys te m s control
button
> Ser vicin g & checks > Air su sp .: jack
mode > On .
• Engage the pa rki ng bra ke to prevent your vehi­
cle from rolling un intent ionally .
"' Move the
sel ect or l ever to position P .
"' Fin d the mark ing (imprint) on the sill that is
nea rest the wheel that will be changed
¢
fig. 206 . Behind the marking, there is a l ift­
in g po int
on the sill for the vehicle jack.
• Vehicles with a sill: remove the
cover from the
sill before lifting the vehicle with a veh icle jack
¢ page 258.
"'Turn the vehicle jack located under the lifting
point on the sill to ra ise the jack until its arm @
¢
fig . 207 is located under the designated plas ­
tic mount ¢ ,&. ¢0 .
"' Align the jack so that its arm@¢
fig. 207 en­
gages i n the designated lift ing po int in the door
sill and the movable base @ lies f lat o n the
ground . The base @ must be
vertical under the
lifting point @. ..,.
257

Emergency assistance
.,. Wind the jack up further until the flat tire
comes off the ground
c> ,&. .
Posit ion the veh icle jack only under the designat­
ed lifting points on the sill
r::!;> fig. 206. There is ex­
actly
one location for each wheel. The jack must
not be positioned at any other location
c> &, c>(!).
An unstable surface under the jack can cause the
vehicle to slip off the jack. Always provide a firm
base for the jack on the ground . If necessary
p lace a sturdy board or similar support under the
jack . On
hard, slippery surfaces (such as tiles)
use a rubber mat or similar to prevent the jack
from slipp ing
c> & .
A WARNING
- You or your passengers could be injured
wh ile chang ing a wheel if you do not follow
these safety precautions:
- Position the vehicle jack only at the desig­
nated lifting po ints and align the jack .
Otherwise, the vehicle jack could slip and
cause an injury if it does not have suff i­
cient hold on the vehicle.
- A soft or unstable surface under the jack
may cause the vehicle to slip off the jack.
Always provide a firm base for the jack on
the ground.
If necessary, use a sturdy
board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipping.
- To help prevent injury to yourself and your
passengers:
- Do not raise the vehicle until yo u are sure
the jack is securely engaged .
- Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
- Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack.
- Changes in temperature or load can affect
the height of the vehicle.
258
(D Note
Do not lift the vehicle by the sill. Position the
vehicle jack only at the des ignated lifting
points on the sill. Otherwise, your vehicle will
be damaged.
@ Tips
The vehicle jack mode * switches off automati­
cally at speeds above 6 mph (10 km/h).
Removing and installing the sill extension
cover
App lies to vehicles: with sill extension
Fig. 208 S ill: r emoving the cove r
.. Pull the cover down to remove it. c> fig. 208
.,. To install the cover, insert it in the mount and
press it upward until it clicks into place. The
cover must be flush with the surface of the sill
extens ion.
@ Tips
Some models may also have a cover for the
rear vehicle lift point.

Emergency assistance
-If the spare tire has to be installed in the incor­
rect direction, use the spare tire only tempora­
rily s ince the tire will not be able to achieve its
optimum performance characteristics with re­ gard to aquaplaning, noise and wear.
- We recommend that you pay particular atten­
tion to this fact during wet weather and that
you adjust your speed to match road condi­
tions.
- Replace the flat tire with a new one and have it
installed on your vehicle as soon as possible to
restore the handling advantages of a unid irec­
tiona l tire .
Notes on wheel changing
Please read the information r=:> page 240, New
tires or wheels
if you are going to use a spa re tire
which is diffe rent from the tires on your vehicle.
After you change a tire:
-Check the tire pressure on the spare immedi­
ately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or a
qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 90
ft lb (120 Nm).
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
tightening torque.
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover .
Until then, drive with extra care and at reduced
speeds .
.8, WARNING
-If you are going to equip your vehicle with
tires or rims which differ from those which
were factory installed, then be sure to read
the information
r=;, page 240, New tires or
wheels .
260
-
-Always make sure the damaged wheel or
even a flat tire and the jack and tool kit are
properly secured in the luggage compart­
ment and are not loose in the passenger
compartment.
- In an accident or sudden maneuver they
could fly forward, injuring anyone in the ve­
hicle.
- Always store damaged wheel, jack and tools
securely in the luggage compartment. Oth­
erwise, in an accident or sudden maneuver
they could fly forward, causing injury to pas­
sengers in the vehicle.

Emergency situations
pulled out when towing the vehicle and that
could cause an accident.
Rear towing loop
Only install the rear towing loop when it is need­
ed.
0 0
Fig. 219 Rear bumper: c over
0 0
Fig. 220 Rear bump er: sc rew ing in towing loop
There are threads located behind the right side of
the rear bumper where a towing loop can be in­
stalled. The threads are located behind a cover.
" Remove the towing loop from the vehicle tool
kit .
.. Press inward strongly to the button side of the
cap to remove it from the bumper
r=;,fig. 219 .
"Screw the towing loop tightly in the threaded
hole as far as it will go and tighten it with the
wheel wrench
r=;, fig. 220.
Remove the towing loop when you are done using
it and place it back in the vehicle tool kit . Always
keep the towing loop in the vehicle.
&_ WARNING
If you do not screw the towing loop complete­
ly, it could come out of the threaded hole
while the vehicle is being towed causing dam·
268
age to the vehicle and possible serious per­
sonal injury .
Loading the vehicle onto a flat bed truck
Fig. 221 Vehicle on flat bed tru ck
Front hook up
:g N 0 t!, .., m
"Align the vehicle with the centerline of the car
carrier ramp .
.. Attach the w inch hook to the front towline eye
previously installed.
Rear hook up
"Align the vehicle with the centerline of the car
carrier ramp .
.. Attach the winch hook to the rear towline eye
previously installed.
@ Tips
Check carefully to make sure the hook-up is
secure before moving the car up the flatbed
truck ramp.
Vehicle transport
Whenever you hove your vehicle transported, be
sure to note the following:
(D Note
Mount the tie-down chains/cables over the
running surface (circumference) of the tires.
Never secure the vehicle by the axle, the sus­
pension struts or the front or rear towline
eye. For technical reasons, the pressure in the
suspension struts may change during the
transport and this will adversely affect vehicle handling.