2016 AUDI A8 jack points

Emerg ency assis ta nce
Position the vehicle jack only under the designat­
ed lifting po ints on the sill
¢fig. 219. There is ex­
actly
one locat ion for each wheel. The jack must
not be positioned at any other location
c> &<=>0.
An uns table su rf a ce under the jack can cause the
vehicle to slip off the jack. Always provide a firm
base for the jack on the ground . If necessary
place a sturdy board or similar support under the
jack. On
hard, slippery su rfaces (such as tiles)
use a rubber mat or similar to prevent the jack
from slipping
c> ,&..
A WARNING
-
-Yo u or your passengers could be injured
wh ile chang ing a wheel if you do not follow
these safety precaut ions:
- Position the vehicle jack only at the desig­
nated lifting points and align the jack.
Otherw ise, the vehicle jack cou ld slip and
cause an injury if it does not have suffi­
cient hold on the vehicle.
- A soft or unstable s urface under the jack
may cause the vehicle to slip off the jack.
Always p rovide a firm base for the jack on
the ground. If necessary, use a sturdy
board under the jack.
- On hard, s lippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slippi ng.
- T o help prevent injury to yo urself and yo ur
passenge rs:
- Do not raise the vehicle unti l you are sure
the jack is securely engaged .
- Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
- Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack.
- Changes in temperature or load can affect
the height of the vehicle.
(D Note
Do not lift the vehicle by the sill . Position the
vehicle jack only at the designated lifting
262
points on the sill. Otherwise, your vehicle wi ll
be damaged .
(1) Tips
The vehicle jac k mode sw itches off automa ti­
cally at speeds above 10 km/h.
58: Raising the vehicle
The vehicle must be li~ed with the jack first be ­
fore the wheel can be removed .
Fig. 221 Sill panels : ma rkings
F ig. 222 Sill : pos ition ing the veh icle jack
.. Activate the vehicle jack mode in the MMI :
!CARI function button > Car s yst ems control
button
> Ser vicin g & che cks > A ir su sp .: jack
mode > On .
.. Engage the parking brake to prevent your vehi­
cle from rolling uni ntentiona lly .
.. Move the
select or lever t o positi on P.
.. Find the marking (imprint) on the sill that is
nearest the wheel that will be changed
<=>fig. 221 . Behind the marking, there is a lift­
ing point
on the sill for the vehicle jack.
.. Turn the
vehicl e jack located under the lifting
point on the sill to raise the jack until its arm
@ Ill>

c::> fig. 222 is located under the designated plas­
tic mount
c::> A in AB: Raising the vehicle on
page
262 <=:>(D.
.. Align the jack so that its arm®
c::> fig. 222 en­
gages in the designated lifting point in the door
sill and the movable base ® lies flat on the
ground . The base ® must be
vertical under the
li ft ing po int @ .
.,. Wind the jack up further unt il the fla t tire
c omes off the ground
c::> A in AB: Raising the
vehicle on page
262.
Position the veh icle jack
onl y under the designat­
ed lifting points on the sill
<=:>page 261, fig. 219 .
There is exactly one locatio n for each wheel. The
jack must not be positioned at any other location
c::> .&. in AB: Raising the vehicle on page 262<=:> 0.
An
un stabl e surface under the jac k can ca use the
vehi cle to slip off the jack . Always provide a firm
base for the jack on the ground. If necessary
p lace a sturdy board or similar support under the
jack. On
hard , slippery surfaces (such as tiles)
use a rubber mat or similar to prevent the jack
from slipping
c::> .&. .
A WARNING
-
-You or your passengers could be injured
wh ile chang ing a wheel if you do not follow
these safety precautions :
- Position the vehicle jack only at the desig ­
nated lifting points and align the jack.
Otherw ise, the vehicle jack cou ld slip and
cause an injury if it does not have suffi­
cient hold on the vehicle.
- A soft or unstable surface under the jack
may cause the vehicle to slip off the jack.
Always provide a firm base for the jack on
the ground .
If necessary, use a sturdy
board under the jack.
- O n hard, s lippery surface (such as tiles)
use a rubber mat or s imilar to prevent the
jack from slipp ing.
- To help prevent inju ry to yourself and your
passenge rs:
- Do not raise the vehicle unt il you are sure
the jack is secure ly engaged .
Emergen cy a ssis tanc e
-Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
- Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack .
- Changes in temperature or load can affect
the height of the veh icle.
(D Note
Do not lift the vehicle by the si ll. Position the
vehicle jack on ly at the designated lift ing
points on the sill. Otherwise, your veh icle w ill
be damaged.
@ Tips
The vehicle jack mode switches off automati­
cally at speeds
above 10 km/h.
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang­
ing the wheel .
Fig . 223 Cha ngin g a w heel: us ing the screwdriver handle
(wit h the b lade removed) to turn th e bolts
Fig. 224 Changing a w hee l: a lig nment p in in side the top
hole
263

eye. For technica l reasons, the pres sure in the
suspension st ruts may change during the
t ra nspo rt a nd this will adverse ly affect vehicle
handling.
Raising the vehicle
Lifting with workshop hoist and with floor
jack
T he vehicle may only be lifted at the lifting
poin ts illus trated .
Fig . 237 Front lift ing point
F ig. 238 Rear lift ing po int
.,. Read and heed WARNING¢&_.
... Activate the vehicle jack mode in the MMI:
I CAR I funct io n button> Car system s control
button >
Servicing & checks > Air susp .: jack
mode > On .
... Loc ate lift ing po ints ¢fig. 237 and ¢ fig. 23 8 .
.,. Adjus t lifting arms of wo rkshop hoist or floo r
jack to matc h ve hicle lifting points .
... Inse rt a ru bber pad between t he f loor jack/
workshop hoist and the lifting points.
T h e vehicle jack mode m ust be act ivate d so that
the automatic adjustment of the Adaptive Air
Suspension does not ma ke it more diffic ult to
raise the ve hicle w it h the floor jack .
Emergency situations
If you must lift your vehicle with a floor jack to
work unde rneath , be sure the vehicle is safely
supported on stands intended for this purpose.
Front lifting point
T he li fting poi nt is locate d on the floor p an rein­
f o rcement about at the sa me level as the ja ck
mounting point¢
fig. 237 . Do not lift the vehi­
cle at the vertical sill re inforcement .
Rear lifting point
T he lif ting point is locate d on the vertical rei n­
f o rcement of the lowe r sill for the on-bo ard j ack
¢fig. 238 .
Lifting with vehicle jack
Refer to¢ page 261 .
A WARNING
-- To reduce the r is k of se rious inju ry and veh i-
cle dama ge.
- Always lift the vehicle on ly at the special
w orkshop hoist and f loor jack lift points
il ­
lu strated¢ fig. 237 and¢ fig. 238.
- Failure to lift the ve hicle at these points
could cause the veh icle to tilt or fall fr om
a lift if t here is a change in vehicle weight
dist ribution and balance . Th is m ig ht hap­
pen , fo r e xampl e, wh en heavy compo­
n ents such as the eng in e block o r trans­
mi ssion are removed.
- W hen re mov ing heavy componen ts like
t hese, anchor veh icle to hoist or add co rre­
s p ondin g weig hts to maintai n the center of
g ra vity. O therw ise, the vehicle mig ht tilt or
slip
o ff th e hois t, c ausing se rious pe rsonal
i njur y.
(D Note
- Be aw are of the fo ll ow ing poi nts before lift­
ing the vehicle:
-The vehicle should never be lifted or
jacked up from underneath the engine oil
pan, the transmission housing, the front
or rear axle or the body side members .
This could lead to serious damage .
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
275

Emergency situations
inserted between the floor jack and the
lift points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity of
the hoist.
- Before driving over a workshop hoist, en­
sure that there is sufficient clearance be­
tween the hoist and low parts of the ve­ hicle.
276